FCC Compliance Statement Model Name: Cobra NVR This device complies with Part 15 of the FCC Rules. Operation is Subject to the following two conductions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. WARNING Unauthorized reproduction of all or part of this manual is strictly prohibited.
【Warning and Caution are indicated as follows.】 Possible injury or product damage. Risk of minor injury or product damage. Cautions for the usage of the product. Information for the usage of the product.
Chapter １. Introduction ................................................................ ................................ ................................... ................................ ... 3 １- １ NVR Model Major Features ..................................................................... 3 １- ２ Components ........................................................................................ 4 Chapter ２. Installation and connection ........................................... ......................
Chapter １. Introduction １-１NVR Model Major Features Line Up OS System Camera Access Live monitoring, Recording, Playback, Backup, Network, Setup USB2.0 Memory stick, Network IP Camera Up to 16 Channel Max. 120 / 100 fps 16 IP Camera / HDMI Compression H.264 Resolution Go to first rec. time, Go to last rec.
EOL Register(10K) ★ 4Ch Digital Zoom PoE port x1 ~ x16 4 port or 8 port PoE support Watermarking Yes Detection / Search Motion, Sensor Fan Fail Features E-mail Yes 5 User with still image Capture 1080p iSCS Recording Yes DDNS, DHCP, UPNP Yes VMS, RMS Smart Phone (3G) Windows Android, iPhone, iPad Mac Viewer Power Supply ★ Apple Mac OS NVR:12V/5A - Level 5 PoE : 48VDC / 1A (4PoE), 48VDC / 2A (8PoE) NVR:12V/5A-Level/40Watts Consumption General Operation Temp / Humidity PoE : 48VDC / 1A (
Chapter ２. Installation and connection ２-１NVR Front Panel No.
No. Name Feature Type 1 e-SATA External SATA USB Type A, e-SATA 2 TV CCTV monitor displays the output images.
1 PoE Power PoE power DIN jack 2 PoE Ethernet PoE IP camera (4port or 8port) RJ-45 3 AUDIO IN Audio Input (Line Only) RCA 4 VGA-OUT VGA or LCD D-SUB 15P 5 e-SATA external SATA USB Type A, e-SATA 6 TV CRT Monitor BNC 7 HDMI HDMI output HDMI type-C 8 VGA-OUT VGA or LCD D-SUB 15P 9 Ethernet Ethernet 10/100 Base-T RJ-45 10 Terminal Block RS-485 / Sensor / Relay / POS Terminal Block 11 CONFIG NTSC / PAL DIP S/W, 2-pin 12 Power 90 ~ 250V, 50 / 60Hz, 80 Watts AC Inlet
２-５ Terminal Block The terminal blocks in the rear of the product are for the connection of PTZ / Sensor / Relay / POS Connection. The number of the terminal block may be different depending on the model. ① PTZ Camera/Keyboard Controller Connect PTZ control cable; TRX+, TRX- and GND to Terminal Block(TB1);No.4 TRXD+, No.5 TRXD- and No.10 GND in the rear of NVR. You may refer to APPENDIX for supported PTZ cameras in this manual. Keyboard controller has the same connection as PTZ camera.
ESC Exit the current menu or Move to the upper menu. PREV Move back (Reverse) PAUSE Pause FORWARD Move forward BACKWARD Playback PLAY Play ３-２ Mouse The mouse pointer as shown below appears if a mouse is connected to the USB terminal at the front panel. Mouse Control functions are shown below. Click on the right button Monitoring Mode / Move from Play Mode to Monitoring Menu / Pop up or remove Play Menu. Show sub-folder of the certain Menu window. Click on the left button Select Menu.
Chapter ４. NVR Operation Setup ４-１Power ON. ① Check the adapter, and connect the power. ② Once Power cable is connected (found in Rear Side), booting will be enabled. ③ After booting is finished, the live screen and channel indication / clock are shown. ④ Menu window pops up by clicking the right button of the mouse as shown below. ID and Password are required for initial installation.
After an IP Camera is found, the IP Cameras “Port, ID, password, protocol” can be inputted. Please take careful note that if there is any mistake or ‘typo’ in any of the 4 Settings (Port, ID, PW, Protocol), then connection will not be possible ４-４POE Connection ① Connect the PoE Power adaptor on NVR to turn on PoE. ② Input PoE IP camera to the PoE Port on NVR. 4PoE NVR support PoE from channel 1 to channel4 and the other 12 channels can be connected to the IP cameras connected into the same network.
４-- ５-- １ Real Time Monitoring Mode and Icon After booting is finished, Audio/Recording Status/Channel Title/Connection Status/Time/HDD Status are displayed as shown below. [ ※ Recording Event / Recording Mode Icon ※ Motion Detection Recording Recording Event Sensor Recording Text Recording Video Recording Recording Mode Audio Recording Text Recording ※ Recording Event Icons are still displayed despite of the recording stop. Recording Mode Icon distinguish recording status.
① Full Screen ② 4 Channel Screen ③ 8 Channel Screen ④ 16 Channel Screen ⑤ ZOOM function ⑥ Auto Sequence Mode ⑦ Date / Time ⑧ HDD Status ⑨ Playback ４-- ５-- ２ Screen Division and Auto Sequence After the system is booted, images will be displayed on a screen divided into 16 division. Except for the basic setting, the system follows user’s setting on the screen division from next booting.
※ Auto Sequence Auto Sequence is to rotate images at an interval of the certain time in 1 / 4 / 9 Basic Division. Auto Sequence is not available in the Basic 16 Division mode. ① Move to {Menu} {Miscellaneous} {Display Setup }. ② Pressing Remote Controller {SELECT} Button / Mouse Arrow Button initiate the Auto Sequence mode.
４-- ５-- ４ Zoom Zoom is to zoom in or out the 1 channel division image in the real time monitoring mode. ① Move to {Menu} {Zoom} or press the zoom icon from the control bar in the real time monitoring mode. ② After selecting a channel, it becomes the 1 channel mode and the zoom control screen sho ws at bottom-right. [Figure 5-1. Zoom Control Screen] ③ In case of the mouse, move the pointer to an area to be zoomed in the zoom control scree n and double-click on it.
In the PTZ mode, there are two function; Full and Mini. Tour has [Tour1] and [Tour2]. Home Position Time is 1 / 5 / 10 / User setting(1-60)minutes. Preset? Using horizontal / vertical / Zoom / Focus / Iris movement of PTZ Camera, zoom or focus or Iris a certain spot of the image by designating the coordinates and move to the designated coordinates quickly. Home Position Time? If there are no controlling signals to PTZ camera after a certain time, it goes automatically to the Preset No.
４-- ６-- １ Playback and Playback Speed Control ① In the Playback mode, the user can play back video contents by using buttons as shown be low. ② After the data is played to the end, the data of the next time zone will be automatically sear ched and played (this function is possible only in the Multi-channel Playback mode; both bac kward playback and forward playback are possible). ③ Pressing buttons, the user can adjust the playback speed by(ⅹ1) / (ⅹ2) / (ⅹ4) / (ⅹ8) / (ⅹ16) / (ⅹ32) / (ⅹ300).
Type Content Sensitivity 5 levels; Lowest / Low / Middle / High / Highest Minimum Mosaic pixel control available between 1- 10 Quick Search Detail Search In the NTSC mode, search 30 frames once. In the PAL mode, search 25 frames once. Search all frames. ① Move to the Smart Search and select the desired channel. ② After shifting to the 1 channel mode, select areas to be smart searched. ③ The 14 * 15 pixel mosaic mode appears. In the beginning, all pixels are selected.
⑤ It may take time during the searching. Start the playback after searching. After searching, status bar shows information of detected images from the object movement ４-- ６-- ３Panorama Search Panorama Play is to play recorded images of the certain channel frame by frame.
４-- ６-- ６ MULTI TIME The user can playback the video recorded image of the certain channel recorded in different time zones simultaneously. The arrangement of the searching result is the past to recent format. ４-- ６-- ７ MULTI DAY The user can playback the video recorded image of the certain channel recorded in different dates simultaneously. The arrangement of the searching result is the past to recent format.
４-７Setup ４-- ７-- １ Time ※ Function Description 1. Time Synchronization 1) Synchronization with the NTP server The time is synchronized once every hour with the NTP Server. A. Automatic Setup The nearest server from the user’s zone will be selected for connection. If the connection fails, the next nearest server will be chosen. B. User Setting The user sets the URL or IP for the NTP server. If connection is not established, a message will be sent to the user, and the related log, saved.
(1)Time Sync ① Select Time Sever / Sever Type / Sever URL. Off The time server is not used. NTP NTP is used to set the time for the time NVR. {NTP} setup is available when {Time Sync} is set as NTP. The user can enter the IP only when the server type is NVR. For the NTP server, Automatic, IP, or URL should be selected. (2) Date and Time ① Date and Time Only available when Time Server is off. The system date and time format is Year/Month/Day Hour/Minute/Second.
When an IP Camera is ‘Added’, the user can input the IP camera’s IP, Port, ID, password, protocol in order to connect. Please take careful note that if there is any mistake or ‘typo’ in any of the 4 Settings (Port, ID, PW, Protocol), then connection will not be possible.
③ IP Camera Reboot 등록되어 있는 IP 카메라를 NVR에서 에서 재부팅하도록 할 수 있다. 있다 ④ IP Camera Find By using the ‘Search’ Button, the NVR can search for IP Cameras within the same ‘network’. After an IP Camera is found, the IP Cameras “Port, ID, password, protocol” can be inputted. Please take careful note that if there is any mistake or ‘typo’ in any of the 4 Settings (Port, ID, PW, Protocol), then connection will not be possible (2) PTZ This enables the user the real-time monitoring by using PTZ camera.
① Configure Protocol / Duration / Tour. ※ The Protocol depends on the IP Camera Manufacturer’s protocol. ※ Duration can be selected at 5 / 10 / 15 / 20 / 5-60 (User setting) seconds. ※ Tour consists of Tour 1 / Tour 2 and each tour can be set with 8 Preset. (3) POS Setup the protocol and baud rate of the POS device. (4) Event Source Select {Menu} {Setup} {Camera} {Event Source}. ① Motion Area The user can setup the motion detection area. Area setup related to motion can be decided.
② Motion Sensitivity : Lowest/Low/Middle/High/Highest. ③ Sound Sensitive : Lowest/Low/Middle/High/Highest. ④ Sensor Type : Select the sensor type. ⑤ EOL : EOL Function Select (On / Off). ⑥ Relay : Select the relay type. ４-- ７-- ３ Recording The Main setup is to configure the environment of record and system and major functions. In the real-time monitoring, move to {Menu} {Setup} {Recording} (1) Schedule Selection (Schedule1 ~ Schedule4) Each channel can be scheduled in 4 different schedules.
(3) Recording ① Recording Resolution Used to set the resolution of the recorded channel. Resolution by Video Type Type esolution D1 NTSC PAL 704 x 480 704ⅹ576 720p 1280ⅹ720 1080p 1920 x 1080 ② Frame Rate The Recording ‘Frame Rate’ setup can be set between “0~30”, with the total frame rate at 120fps. ③ Bitrate The Recording Resolution ‘Bitrate’ can be changed in this setting. ④ Audio Used to set the recording of the external audio input linked to the system.
This function is used to generate alarms through the Buzzer / PTZ Preset / e-mail / Relay / Popup if user sets ‘Motion, Sensor, Text input’ in {Setup} {Recording} {Event} and events occurs. ① PTZ Preset : Set up PTZ Preset in PTZ Control Menu.(Please refer to the image below) PTZ preset can be configured between 1-16. ② E-mail : Set up E-mail in ‘2.Relay SMTP’. When events occurs, user will receive email based on settings in ‘3. Interval’ ③ Relay : Send a signal in Relay based on settings by user.
(6) Log Setup On / Off for Motion / Sensor / Text Input. ４-- ７-- ４ Schedule NVR model provide 4 different recording mode configurations. Each schedule mode can be set one week/24 hours and the recording follows the setting automatically. (7)Schedule Setup Select one schedule among Schedule1, Schedule2, Schedule3 and Schedule4. Selection Tip ① Select the day and time to be set by using the arrow keys. ② Select after moving the cursor onto Time(0-23) or Day(Sun.
４-- ７-- ５ Storage In the Storage menu, To apply the new setting, save the new setting after changing the setting. Reset: Initialize the menu to the basic setting. (1) Max. Recording Days This is to limit the recording days. You can set None/1day/7days/30days/User setting(1-31). (2) HDD Overwrite ① Select On/Off for HDD Overwrite. On If there is no more hard disk space left, the existing files will be overwritten by starting with the oldest.
③ Backup The backup storage is managed in Backup. Backup storages are not used to store data; rather, they are only used to back up the data. The user can execute only the {New} command. Depending on the storage type, the storage is used only for (Recording) or (Backup) purposes. ④ New All storages, initially detected are managed in {New}. All initially detected storages are displayed as New and can be changed into Recording storage or Backup Storage.
(5) Instruction when adding the local storage device ① Open the system body and install a new disk (connect the data cable and the power cable) ② Connect power to the system and boot the system. ③ Select {Menu} {Setup} {Storage} by using the arrow keys and the Select button. ④ A newly displayed disk will then be displayed as {New}. ⑤ Select a newly installed disk by using the arrow keys and the Select button and initialize the disk as a {Recording} or a {Backup} disk.
４-- ７-- ６ Network (1) Ethernet This is to use a fixed IP in the Local Area Network environment. ① IP Address, Subnet Mask, Default Gateway, Primary DNS, and Secondary DNS will be set a utomatically when the {Ethernet Type} was selected to ‘DHCP’. ② Users can input the IP Address, Subnet Mask, Default Gateway, Primary DNS, and Seconda ry DNS manually when the {Ethernet Type} was selected to ‘static’.
① Select On/Off of DDNS or a domain name to use by using arrow keys and the selection but ton. ② In case of DDNS On, enter the host name and save it then, the registration procedure of th e host name proceeds automatically. You can enter the host name with 4-20 letters. ③ The host name to enter must not be pre-registered in DDNS sever. Otherwise it won’t work. ④ The basic host name is the MAC address of appertaining NVR.
This is to set automatic E-mail transmission service when an event occurs. To use the e-mail function, {E-mail} in {Menu} {Setup} {System} {7. Alarm} or {E-mail} in {Menu} {Setup} {Action} { Alarm} need to be configured. ② Relay SMTP is set on ‘Gmail’ as default, but when ‘Default’ (in menu tab) is selected, this will changed to dvr@cctvuser.com. ③ Receiver Email can be set up to 5 users (emails). ④ Email Interval settings are as follows [5 sec / 1 min / 3 min / 5 min /10 min].
(5) Bandwidth Move to {Menu} {Setup} {Network} {Bandwidth}. This sets up adjust resolution / quality and transmitting the data by using the network. Image Resolution D1 Image Quality Adjust quality of the image, as the value increases, the compression rate gets higher and image quality gets low. However the transmission rate gets higher. Transmission Codec JPEC / H.264 ４-- ７-- ７System System 1. NVR Name Used to name the NVR device. 2.
(1) NVR Name . The initial value is the Mac address. (It supports up to 20 letters for the system name.) (2) ID For Keyboard Controller ① Move to {Menu} {Setup} {System} {2. ID for Key Controller}. ② In the selection window, enter ID by using the arrow keys and the Select button (number 1~ 255 is available for ID.) (3) User Registration ※ Add, edit, or delete the users who will operate the system and give authorities to users as shown below.
① Firmware Upgrade ① Select {Firmware} and the upgrade file list stored in the selected device and simple version i nfo of the selected file are then displayed. Select a file and Firmware Upgrade window appe ars. ※ Downgrading to a previous version is not supported. ※ The upgrade information window will then appear within 15 seconds. ② Read the information and select {Yes} to start the upgrade gradually. Select {No} to return to the {System} mode. ③ After the upgrade is completed, the system reboots.
※ Popup Window Setup at {Menu} {Setup} {System} {7. Alarm}. Popup Window is to pop up the system check window in the monitoring screen as shown. it indicates [Video Signal loss/ HDD full/ HDD Not Detect / FAN fail/ Storage Fail/ Storage Warning / Sensor Connection Tamper]. (9) Alarm Duration ① It sets the duration of the alarm triggered by the recording and system event. ② Move to {Menu} {Setup} {System} {8. Alarm Duration}.
４-８Search ４-- ８-- １ Search Mode Move to {Menu} {Search} in the real-time monitoring mode. (1) Calendar Search Calendar Search allows the user search and playback by [Year / Month / Day / Hour / Minute], [MultiChannel / Multi-Time / Multi-Day] and [Motion / Sensor]. ① Search Mode On the real-time monitoring screen, select {Menu} {Search} {Calendar Search} and then a searching window pops up as shown below. ② Year / Month / Day Selection Select the desired [Year / Month / Day].
⑤ Multi-Channel Search The Multi-Channel Search is to play recorded images of the different channel over a certain designated time. ⑥ Multi-Time Search The user can playback the video contents of the certain channel recorded in the different time zone simultaneously. Entering into the search mode during the Multi-Time playback leads to the Multi-Time Search. ⑦ Multi-Day Search The user can playback the video contents of the certain channel recorded in different dates simultaneously.
⑨ POS Search Mode On the real-time monitoring screen, select {Menu} {Search} {POS Search} and then a searching window pops up as shown below. ⑩ Year / Month / Day / Text / Time Selection Please select date/time, Time index, Text 1, 2, 3, and select the start time within the channel. ⑪ Search / Playback After selecting the ‘Start’ Button, ‘1 searched item’ needs to be selected in order for ‘playback’ to start.
(2) Backup in Search Mode ① Select {Menu} {Search} {Calendar Search}. ② Click the right-mouse button. ③ The automatic backup start time is set to the year/month/date/hour/minute set in the search mod e, and the end time, to the last minute/second of the data existing at the selected time. ④ All channels with existing data at the time of backup are backed up automatically. ⑤ For the remaining backup procedures, see [5-12-5 Common Backup Procedure].
① shows the initial backup window menus. ② A list of the devices that can be selected is outputted with simple information of the currentl y selected devices ③ Selecting a device by pressing the Select button causes the free space and total capacity fo r the selected device to be displayed. ④ Selecting a device causes the directory name based on the initial values for the time and ch annel to be displayed and the size of the file to be backed up to be calculated.
.Log files are created at a folder shown below. 565645348945_20100303.log .log file is the text file. ４-- ９-- ４ Setup Backup The Setup Backup is to back all setup values of the current menu up. This function enables the user to copy the setups and apply them into other devices. ① For the Setup Backup, a device for backup must be connected. ② Move to {Menu} {Backup} {Setup Backup} and a window shown below appears. The s etup is copied by the name shown below. Saved as the name below.
③ Move to {Menu} {Setup} {System} {4. Upgrade} ->{Setup} after insert the backup de vice. ④ With this way, the user can upgrade a new device with the current setup values in easy wa y. ４-１０Miscellanea ４-- １０-- １ System Information Information ４-- １０-- ２ Log Viewer NVR records all Log information over the system operation including Power on/off, System Setup and Network Access. Move to {Menu} {Miscellaneous} {Log Viewer} to see the logs.
Log Type General Logs related to power ON / OFF, file copy/backup failure, setup start/end, playback, and other basic system operations. Recording Event Logs related to the recording including motion detection and sensor detection. Network Logs related to network operations including network login, network logout, and network live. Fail Logs related to system operation failures including signal loss and network connection failure. All Logs related to all system operations.
４-- １０-- ３ Control In the real-time monitoring, move to {Menu} {Miscellaneous} {Misc. Control}. ① Move to the Audio tab and select the channel to be activated or Mute. ② Move to the Relay tab and select. ③ Move to the Text tab and select. NVR model support only 1 channel text input. ４-- １０-- ４ Display Setting Camera Title On/Off, Control Bar On/Off, Button Sound On/Off, Border Line Draw/Width/Color, Screen Saver, Main Sequence.
① Screen Saver Monitor connected with NVR can be shut down to protect monitor.
A/P/P/E/N/D/I/X Recommended HDD Specification Recommended USB2.0 Device USB2.0 Device Media File System Memory Stick Flash Type FAT32 2.
