Instruction manual

ManualsBrandsSigma ManualsCamera AccessoriesEM-140 DG Macro Flash Canon

TTL MODE

TTL mode can provide correct exposure for subject, and will control the amount of flash.

ۋ Please refer to <<CHART A>>, which shows the combinations of camera and lens types, exposure

mode, and flash modes.

ۋ TTL function does not work, in the case of Cameras F3 series, FM10, New FM2, FE10.

1. Set the exposure mode of the camera. (However, depending on the

camera, exposure setting may vary). Please refer to Camera’s

Instruction manual.

2. Slide the Flash’s power switch to the ON position.

3. Select TTL/BL or TTL by pressing the MODE button.

When you use Digital SLR Camera, please do not fail to select TTL/BL.

CLS compatible models are controlled by i-TTL exposure system. CLS

incompatible models are controlled by D-TTL exposure system. In both

cases, the character "

" (digital) will be displayed on the LCD panel.

ۋ In the case of cameras; F6, F5, F4 series, F100, F90X/F90/F80

(N90S/N90/N80) series, F70D/N70, F810S/N8008S, F801/ N8008S

and Pronea 600i. TTL/BL or TTL can be selected. However, Nikon

cameras, other than those on the above list can select only TTL.

4. Focus on the subject.

5. Confirm the Ready Light and press the shutter release button.

ۋ When the camera does not receive the appropriate exposure for the subject, the TTL/BL or TTL mark on

the LCD panel will appear for 5 seconds after shooting, which shows that the flash power is not enough

for this situation. Please re-take a closer distance or use a wider aperture.

ۋ When the flash is fully charged, the ready light in the camera’s viewfinder will appear. If it does not

appear, shutter of the camera may operate at a slow shutter speed without triggering the flash.

<<CHART

Camera

Lens Type

Exp. Mode

Metering

TTL System

Note

D Type

All Modes

3-D Multi-Sensor

AF lens other than

D type

All Modes

Multi-Sensor BL

F6, F5

F100

F90X/N90ser.

F80/N80ser.

F70D/N70

Without Built in CPU

A/M

Modes

Center-weighted,

Spot Metering

Center Weighted /

Spot Fill-Flash

Can switch to TTL Mode. With F5, F100,

F80, series Cameras spot metering

system is always TTL.

Matrix Pattern

TTL BL

With Built-in CPU

All Modes

Center-weighted,

Spot Metering

Center Weighted /

Spot Fill-Flash

F4 Series

F-801S/N8008S

F-801/N8008

F65/N65

Pronea 600i

Without

Built-in CPU

A/M

Modes

Center-weighted,

Spot Metering

Center

Weighted/Spot

Fill-Flash

Can switch to TTL Mode. TTL BL can

work with only F4 series, AF F3, Ai-S,

Ai, Series E lens. Spot metering system of

F4 is always TTL. Pronea 600i will be

TTL, when exposure mode is “M”.

Center Weighted BL cannot work.

Matrix Pattern

TTL BL

With Built-in CPU

All Modes

Center-weighted,

Spot Metering

Center Weighted /

Spot Fill-Flash

F601/N6006

F-601M

Without

Built-in CPU

A/M

Modes

Center-weighted,

Spot Metering

Center Weighted /

Spot Fill-Flash

Spot Metering cannot use with

F-601M

With Built-in CPU

P/S

A/M

TTL BL

If exposure mode is “M”, it will be Center

Weighted/Spot Fill-Flash

F60D/N60

F50D/N50

F-401X/4004S

Without

Built-in CPU

Center Weighted /

Spot Fill-Flash

TTL Programmed

Built-in CPU lens

,Ai-S, Ai, Series E,

AF F3 Lens

A/M

TTL

F501/N2020

F301/N2000

Except above

lenses

A/M

TTL

P/S

TTL Programmed

With Built-in CPU

A/M

TTL

F401S/N4004S

F401/N4004

Without Built-in CPU

TTL

FA, FE2

FG, F3

With Built-in CPU;

Without Built-in CPU

A/M

TTL

When you use Digital SLR cameras, functions will vary depending on the lens type and combinations of exposure

modes, same as F5 and F100 group. (However, all TTL exposure functions will be the D-TTL (i-TTL) system).