DIGITAL SWITCHERS 2100 SERIES HIGH PERFORMANCE DIGITAL ROUTING OPERATORS MANUAL Includes Module and Frame Information for: AUDIO DAS-2144 DAS-2188 DAS-21616 VIDEO DVS-2144 DVS-2184 DVS-21164 DVM-1616 DVS-1616 SIGMA ELECTRONICS, INC. P.O.
100 DIGITAL TABLE OF CONTENTS SECTION 1 OPERATORS MANUAL Specifications ............................................................................................. Page Unpacking .................................................................................................. Page Installation .................................................................................................. Page Interconnect Wiring ....................................................................................
2100 DIGITAL Specifications DIGITAL VIDEO SWITCH FRAME (DVS -1616, DVM-1616, DVS-2144, DVS-2184, DVS-21164) DIGITAL VIDEO INPUT: Input Signal ................... ........................................................ 16, Single-ended, terminated 75Ω Input Level ..................... ........................................................ SMPTE 259M, 800 mVp-p Data Rate ...................... ........................................................ 400 Mb/s maximum Input Cable Length (DVS-1616)...........
2100 DIGITAL Specifications (cont.) SYSTEM CONTROL INTERFACE MODULE (SCI-2144) Data Transmission System .................................................... Serial Port Baud Rate ... ........................................................ Control Levels ............... ........................................................ Communication Line ..... ........................................................ Control Panels ............... ........................................................ Protocol .....
UNPACKING Inspect your packages and equipment for any damage that may have occurred during shipping. Report any damages to both Sigma Electronics, Inc. and your shipping company. It is the buyer’s responsibility to file a claim against the shipping company for cost of repair due to shipping damage. 2100 Series frames are shipped fully loaded within the shipping carton. The frame includes the power supply and required system modules. Remove the fully loaded frame from the carton.
SYNC REFERENCE Sync reference may be applied to the SCI-2144 (or SCI-1616 in the DVS-1616). The routing switcher will switch during the vertical interval of the reference signal when applied. This signal is applied to the REF IN input on the rear of the Master frame. In the SCI-2144, the signal is not internally terminated and must be terminated if not looping through the system. More detailed information is provided in the operator’s manual concerning the differences in the DVS-1616.
FRAME: The DVM-1616/DVS-1616 system is provided in a frame designed for rack mounting. The 1 RU frame provides mounting tabs for a standard 19 inch EIA rack cabinet. All components are mounted into the frame from the rear of the unit. This frame does not provide additional card slots for insertion of other 2100 Series modules. The DAS-21xx and DVS-21xx modules can reside in some of four different frames provided by Sigma Electronics, Inc.
DVS-1616 and DVM-1616 SERIES 2100 DVS-1616 SIGMA ELECTRONICS, INC. DVS-1616 FRONT PANEL SCI 1616 CONTROL BUS CLEAR 2 4 6 SERIAL I/O 1 REF IN S1 3 8 10 INPUTS 7 9 5 12 11 14 13 16 1 3 5 2 15 7 4 9 11 OUTPUT 8S 10 6 13 12 15 14 16 FUSE 3.0 AMP SLO-BLO 120 VAC COMM System Control Interface Serial Digital Serial Digital Video Input Video Output DVS-1616 REAR PANEL CONNECTIONS Figure 1 SERIES 2100 Power Supply DVS-1616 SIGMA ELECTRONICS, INC.
DVS-2144, DVS-2184 AND DVS-21164 The DVS-2144 is a four-input to four-output video switch, the DVS-2184 is an eight input to four output video switch and the DVS-21164 is a sixteen input to four output video switch. The inputs; arranged in ascending numerical order, top to bottom; are on the left side of the rear panel. The outputs 1 to 4 are located to the right of the inputs.
DAS-2144 Module Block Diagram DAS-2144 W1 - Level Jumper J6 Logic IC Control Bus CROSS-POINTS Differential Receivers Differential Drivers INPUTS 1 TO 4 The 4x4 digital audio switcher is provided as a one-slot width module. The rear panel has inputs on the top half and outputs on the bottom half of the module. The main PCB, also identified as DAS2144, is directly attached to the rear panel. This card plugs into the frame that supplies power and control data.
DAS-2188 Module Block Diagram DAO-108 DAI-108 P1 J5 / J6 S1 Level / Matrix / Group Logic IC Control Bus CROSS-POINTS Differential Receivers Differential Drivers INPUTS 1 TO 8 OUTPUTS 1 TO 8 S1 Settings Output Group / Matrix / Control Level S1-1 Matrix S1-2 Control Level # ON 8x8 ON 1 OFF 16x8 OFF 2 3 4 Output Group 1 to 8 9 to 16 S1-3 S1-4 ON ON OFF OFF ON OFF ON OFF DAS 2188 Inputs + C - + C - Outputs + C - + C - 1 1 2 + C - + C - 2 + C - + C - 3 3 4 + C - +
DAS-21616 DAO-916 Module Block Diagram S1 Level/Group S1 Level/Group Logic Logic Control Bus DAO-108 Control Bus J7 U4 Crosspoints U4 Crosspoints DAI-916 Output Drivers Output Drivers DAI-108 P1 INPUTS 9-16 OUTPUTS 9-16 OUTPUTS 1-8 INPUTS 1-8 S1 Settings Output Group, Matrix Size and Control Level S1-1 Matrix S1-2 Control S1-3 Size Level ON 8x8 ON 1 ON OFF 16x16 OFF 2 ON 3 OFF 4 OFF Output Group 1-8 9-16 Inputs Inputs + C - + C - + C - + C - + C - + C - + C - + C -
Control Panels The 2100 Digital Series routers will function with any of the 2100 Series Control Panels. The control panels have address switches that allow addressing from one (1) through sixteen (16). There may be as many as sixteen panels on each router system. The panels may be a mixture of Full X-Y master control panels or Single Bus panels that control only one selected output. Most panels offer the selection to operate in either a Preset or Auto-Take mode.
