® SUPER TARGET ® TM AIRGUN PRECISION ENTRY LEVEL TARGET PISTOL OPERATOR’S MANUAL: HANDLING & SAFETY INSTRUCTIONS READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS AIRGUN. DO NOT DISCARD THIS MANUAL. THIS MANUAL SHOULD ALWAYS ACCOMPANY THIS AIRGUN AND BE TRANSFERRED WITH IT UPON CHANGE IN OWNERSHIP, OR WHEN THE AIRGUN IS PRESENTED TO ANOTHER PERSON.
WARNING 1.0 SAFETY WARNINGS READ THIS OWNER’S MANUAL COMPLETELY. DO NOT BRANDISH OR DISPLAY THIS AIRGUN IN PUBLIC. IT MAY BE CONFUSING TO PEOPLE AND MAY BE A CRIME. POLICE AND OTHERS MAY THINK THIS AIRGUN IS A FIREARM. DO NOT USE OR CARRY THE AIRGUN IN SITUATIONS WHERE IT COULD BE MISTAKEN FOR A FIREARM. THIS AIRGUN IS NOT A TOY. TREAT IT WITH THE SAME RESPECT YOU WOULD A FIREARM. ALWAYS CAREFULLY FOLLOW THE SAFETY DIRECTIONS FOUND IN THIS OWNER’S MANUAL AND KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE USE.
WARNING 1.1 EYE PROTECTION Always wear safety glasses that meet the requirements of American National Standards Institute (ANSI) z87.1 and ear plugs whenever you are shooting. Always make certain that persons close to you are similarly protected. If you wear prescription or reading glasses that do not meet this ANSI rating, be sure to wear safety glasses over your corrective glasses. 1.
WARNING 2.0 Description of Airgun 3 1 2 4 6 1. Front Sight 2. Slide 3. Rear Adjustable Sight 4. Hammer 5. Grips 6.
WARNING 3.0 Adjusting the Trigger Understand before firing! Small adjustments will make a noticeable change to the operation of the trigger. Only make 1/4 turn adjustments at a time and test fire the airgun before making further adjustments. The trigger is two stage with adjustments on both stages. Be aware that adjustment to one screw will effect the adjustment of the others and the trigger will only work properly if there is the correct balance between all screws.
4.0 Cocking and Loading CAUTION ALWAYS BE CERTAIN YOU ARE USING THE CORRECT SIZE (CALIBER) PELLET FOR YOUR AIR PISTOL. REFER TO THE MARKINGS ON YOUR AIR PISTOL TO CONFIRM THE CORRECT PELLET SIZE. NEVER REUSE AMMUNITION. BE AWARE OF PINCH POINTS AND KEEP FINGERS OUT OF CLOSING LOCATION BETWEEN SLIDE AND FRAME NOTE: For best results use .177 cal (4.5mm) Flat Head Match pellets under 8 grains in weight. 1. 2. 3. 4. Pull back on hammer and hold to rear. Fig1.
4 6 5 7 5.0 Sighting and Aiming To be a consistent marksman, use the correct sight picture each time you fire the pistol. FOR BEST RESULTS – USE SIG SAUER .
6.0 Firing the Pistol WARNING LOADED PISTOL DO NOT TOUCH THE TRIGGER UNTIL YOU ARE ACTUALLY READY TO FIRE THE AIRGUN. ALWAYS ASSUME AIRGUN IS LOADED. DO NOT POINT IN ANY DIRECTION THAT IS UNSAFE OR HARMFUL TO PERSON OR PROPERTY. Be sure you and anyone near are wearing safety glasses to protect eyes. Make certain that there is a clear, unobstructed path towards target. 1. Aim the pistol at a safe target. Be certain the backstop and beyond are safe targets. 2.
reference section "11.0 Cleaning and Maintenance" before firing a new round. 9.0 Sights 9.1 Windage (Left/Right) Adjustment Using appropriate sized flat head screwdriver rotate screw as indicated on the slide: clockwise or counterclockwise for Rear Sight adjustment 9.
.0 Storage Any airgun should be stored so that it is protected from unauthorized use, including use by children. Always store in a clean, dry place. Before storing the airgun, make sure it is unloaded, and not cocked or pressurized. It is recommended to store the airgun in such a manner to protect against theft and misuse. Always store this Super Target pistol unhinged from hammer and broke open slightly.
12.0 Return and Shipping If you have any questions concerning the performance or return of your airgun please write or call: SIG SAUER, Inc. Attention: Customer Service 18 Industrial Drive Exeter, NH 03833 Phone: (603) 610-3000, option 1 Fax: (603) 610-3004 In the event you need to return your airgun to the SIG SAUER Service Department, here’s what to do: 1.
SIG SAUER 18 Industrial Drive, Exeter, NH 03833 Proof of purchase or warranty registration will be required with any request for warranty repair.
SIG SAUER, Inc. • 72 Pease Boulevard • Newington, NH 03801 USA • +1 (603) 610-3000 An ISO 9001:2015 Certified Company. Manufacturing in the U.S.A. sigsauer.