AirPrime WP7603 Hardware Integration Guide 41111211 Rev 1
Hardware Integration Guide Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Preface Patents This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM®. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing. Copyright ©2017 Sierra Wireless. All rights reserved.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 1: Introduction The AirPrime WP7603 is an industrial-grade LGA 239-pad module that provides voice and data connectivity on LTE and UMTS networks. The module also provides GNSS functionality as a SKU-configuration. Accessories A hardware development kit is available for AirPrime WP-series modules. The kit contains hardware components for evaluating and developing with the module, including: • Development board • Cables • Antennas (Additional antennas may be required to support all bands.
2 2: Power Power Supply The host provides power to the AirPrime WP7603 through multiple power and ground pins. The host must provide safe and continuous power at all times; the module does not have an independent power supply, or protection circuits to guard against electrical issues. For detailed pinout and voltage/current requirements of this module, see the AirPrime WP76XX Product Technical Specification. Module Power States The module has three main power states, as described in Table 2-1.
3 3: RF Specifications The AirPrime WP7603 operates on the frequency bands listed below. Table 3-1: LTE Frequency Band Support Band Frequency (Tx) (MHz) Frequency (Rx) (MHz) B2 1850–1910 1930–1990 B4 1710–1755 2110–2155 B5 824–849 869–894 B12 699–716 729–746 Table 3-2: WCDMA Frequency Band Support a Band Frequency (Tx) (MHz) Frequency (Rx) (MHz) B2 1850–1910 1930–1990 B4 1710–1755 2110–2155 B5 824–849 869–894 a.
Hardware Integration Guide Table 3-5: Conducted Tx Max Output Power Tolerances — WCDMA Rev 1 Jul 17 RF band Min (dBm) Typ (dBm) Max (dBm) B2 22 23 24 Connectorized (Class 3) B4 22 23 24 Connectorized (Class 3) B5 22 23 24 Connectorized (Class 3) 8 Notes 41111211
4: Routing Constraints and Recommendations This section describes general routing constraints and recommendations for the AirPrime WP7603 module. Note: This is a non-exhaustive list of suggested design guidelines. The developer is responsible for deciding whether to implement these guidelines. General Rules and Recommendations Clock and other high-frequency digital signals (e.g. serial buses) should be routed as far as possible from the module’s analog signals.
Hardware Integration Guide Antenna Sierra Wireless strongly recommends working with an antenna manufacturer either to develop an antenna adapted to the application, or to adapt an existing solution to the application. For information on routing constraints for the RF circuit, see RF Circuit on page 11. PCB Specifications for the Application Board Sensitive signals (such as audio, UIM, and clocks) should be protected by ground planes/fills.
Routing Constraints and Recommendations Note: Figure 4-1 shows separate traces for VBAT_BB and VBAT_RF. If VBAT_BB and VBAT_RF share a single power supply, these traces should be connected. Note: For optimal decoupling, place the capacitors on the underside of the board, directly under the pins. • • • • Filtering capacitors (100 nF to 1500 F) are recommended near the module’s power supply.
Hardware Integration Guide USB Interface When the USB interface is externally accessible, ESD protection is required on the USB_VBUS, USB_D+, and USB_D- signals. Thermal Considerations When transmitting, the AirPrime WP7603 can generate significant amounts of heat (due to the internal Power Amplifier) that must be dissipated in the host device for safety and performance reasons.
Routing Constraints and Recommendations Note: The level of protection required depends on your application.
Hardware Integration Guide Signal Reference Schematics DNI UIM1 C5 C6 C7 UIM_DATA GND VPP I/O VCC RST CLK 10nF 100nF 0 UIM_VCC + DNI C1 C2 C3 0 0 UIM_RESET_N UIM_CLK 0 9 SW_A SW_B 10 0 DNI SIM2070-6-0-30-00-A UIM1_DET DNI ESD suppressor DNI VGPIO_1V8 DNI 2 1 3 4 6 Note: Example ESD and SIM connector part numbers listed. Comparable parts may be used instead. Note: Capacitor on UIM_CLK is intended to slow down the clock signal in case of crosstalk.
Routing Constraints and Recommendations 10µF VCC_5V0 Replace with FPF2163 if Autorestart is required USB_VBUS 2 VIN VOUT 5 51K 5% USB_ID 2 5 NC1 A NC2 VCC Y GND 51K 5% 6 GND2 FPF2164 4 DNI 3 51K 5% 1 ISET 7 FLAGB 6 ON GND1 VCC_1V8 3 1 4 470 1% VCC_1V8 Figure 4-4: USB OTG Interface Rev 1 Jul 17 15 41111211
5: Regulatory Compliance and Industry Certifications Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Regulatory Compliance and Industry Certifications 1. The end product must use the RF trace design approved with the AirPrime WP7603 module. The Gerber file of the trace design can be obtained from Sierra Wireless upon request. 2. At least 20 cm separation distance between the antenna and the user’s body must be maintained at all times. 3.
Hardware Integration Guide 5. A label must be affixed to the outside of the end product into which the AirPrime WP7603 module is incorporated, with a statement similar to the following: · This device contains FCC ID: N7NWP76C / IC:2417C-WP76C. 6. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC/IC RF exposure guidelines.
