AirPrime WP7504 Hardware Integration Guide 4119157 Rev 1
Preface Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Hardware Integration Guide Patents This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM®. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing. Copyright ©2016 Sierra Wireless. All rights reserved.
Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Module Power States . . . . . . . . . .
Hardware Integration Guide Important Compliance Information for North American Users . . . . . . . . . .
1 1: Introduction The AirPrime WP7504 is an industrial-grade LGA 239-pad module that provides voice and data connectivity on LTE, HSPA, WCDMA, and CDMA networks. The module also provides GNSS functionality as a SKU-configuration. Accessories A hardware development kit is available for AirPrime WP-series modules. The kit contains hardware components for evaluating and developing with the module, including: Rev 1 Apr.
Hardware Integration Guide Specifications subject to change 8 4119157
2 2: Power Power Supply The host provides power to the AirPrime WP7504 through multiple power and ground pins. The host must provide safe and continuous power at all times; the module does not have an independent power supply, or protection circuits to guard against electrical issues. For detailed pinout and voltage / current requirements of this module, see the AirPrime WP75XX Product Technical Specification. Module Power States The module has three main power states, as described in Table 2-1.
Hardware Integration Guide Specifications subject to change 10 4119157
3 3: RF Specifications The AirPrime WP7504 operates on the frequency bands listed below.
Hardware Integration Guide Conducted Tx power Table 3-5: Conducted Tx Max Output Power Tolerances — LTE RF band Min (dBm) Typ (dBm) Max (dBm) Notes B2 22 23 24 Connectorized (Class 3) B4 22 23 24 Connectorized (Class 3) B5 22 23 24 Connectorized (Class 3) B12 22 23 24 Connectorized (Class 3) B17 22 23 24 Connectorized (Class 3) B25 22 23 24 Connectorized (Class 3) B26 22 23 24 Connectorized (Class 3) Table 3-6: Conducted Tx Max Output Power Tolerances — WCDMA RF band
4: Routing Constraints and Recommendations This section describes general routing constraints and recommendations for the AirPrime WP7504 module. Note: This is a non-exhaustive list of suggested design guidelines. The developer is responsible for deciding whether to implement these guidelines. General Rules and Recommendations Clock and other high-frequency digital signals (e.g. serial buses) should be routed as far as possible from the module’s analog signals.
Hardware Integration Guide Antenna Sierra Wireless strongly recommends working with an antenna manufacturer either to develop an antenna adapted to the application, or to adapt an existing solution to the application. For information on routing constraints for the RF circuit, see RF Circuit on page 15. PCB Specifications for the Application Board Sensitive signals (such as audio, UIM, and clocks) should be protected by ground planes / fills.
Routing Constraints and Recommendations Note: Figure 4-1 shows separate traces for VBAT_BB and VBAT_RF. If VBAT_BB and VBAT_RF share a single power supply, these traces should be connected. Note: For optimal decoupling, place the capacitors on the underside of the board, directly under the pins. • Filtering capacitors (100 nF to 1500 F) are recommended near the module’s power supply.
Hardware Integration Guide USB Interface When the USB interface is externally accessible, ESD protection is required on the USB_VBUS, USB_D+, and USB_D- signals. Thermal Considerations When transmitting, the AirPrime WP7504 can generate significant amounts of heat (due to the internal Power Amplifier) that must be dissipated in the host device for safety and performance reasons.
Routing Constraints and Recommendations The host device must provide adequate ESD protection on digital circuits and antenna ports as detailed in the following table. Note: The level of protection required depends on your application.
Hardware Integration Guide Signal Reference Schematics DNI UIM1 C5 C6 C7 UIM_DATA GND VPP I/O 10nF 100nF 0 UIM_VCC + DNI C1 C2 C3 VCC RST CLK 0 0 UIM_RESET_N UIM_CLK 0 9 SW_A 10 SW_B UIM1_DET 0 DNI SIM2070-6-0-30-00-A DNI ESD suppressor DNI VGPIO_1V8 DNI 2 1 3 4 6 uClamp 3301P 5 Example ESD suppressor: STMicroelectronics DALC208SC6 Note: Example ESD and SIM connector part numbers listed. Comparable parts may be used instead.
Routing Constraints and Recommendations 10µF VCC_5V0 Replace with FPF2163 if Autorestart is required USB_VBUS VCC_1V8 2 VIN VOUT 2 5 A NC2 VCC Y GND FPF2164 4 DNI 3 51K 5% USB_ID NC1 51K 5% 6 GND2 470 1% 5 51K 5% 1 ISET 7 FLAGB 6 ON GND1 VCC_1V8 3 1 4 Figure 4-4: USB OTG Interface Rev 1 Apr.
Hardware Integration Guide Specifications subject to change 20 4119157
5: Regulatory Compliance and Industry Certifications Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Hardware Integration Guide Important Compliance Information for North American Users The AirPrime WP7504 module has been granted modular approval for mobile applications. Integrators may use the AirPrime WP7504 module in their end products without additional FCC / IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC / IC approvals must be obtained. 1. The end product must use the RF trace design approved with the AirPrime WP7504 module.
Regulatory Compliance and Industry Certifications · The radiated power of a collocated transmitter must not exceed the EIRP limit stipulated in Table 5-2. Table 5-2: Collocated Radio Transmitter Specifications Device Collocated transmitters1 Technology WLAN WiMAX BT Frequency (MHz) EIRP Limit (dBm) 2400–2500 25 5150–5850 27 2300–2400 25 2500–2700 25 3300–3800 25 2400–2500 15 1. Valid collocated transmitter combinations: WLAN+BT; WiMAX+BT. (WLAN+WiMAX+BT is not permitted.) 5.
