Kramer Electronics, Ltd.
Contents Contents 1 2 2.1 3 4 5 6 6.1 6.2 6.3 Introduction Getting Started Quick Start Overview Defining the SL-14RC Master Controller Defining the RC-3TB Remote Control Panel (Optional) Connecting the SL-14RC Master Controller Connecting the RS-232 Interface Connecting the Ethernet Port Connecting RC-3TB Remote Control Panels (Optional) 1 1 2 3 4 6 8 9 9 9 6.3.1 6.3.
Introduction 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 1,000-plus different models now appear in 11 groups 1 that are clearly defined by function.
Getting Started 2.1 Quick Start The following quick start chart summarizes the basic setup and operation steps.
Overview 3 Overview The SL-14RC is a highly versatile master room controller that acts as an all-in-one extended remote control panel for control of A/V equipment— especially projectors and associated equipment—in any room (such as classrooms, boardrooms, or auditoriums). It streamlines operations and simplifies control by integrating audio, video, and computer-video sources into a centralized system.
Defining the SL-14RC Master Controller 4 Defining the SL-14RC Master Controller Figure 1 and Table 1 define the front panel of the SL-14RC.
Defining the SL-14RC Master Controller Figure 2 and Table 2 define the rear panel of the SL-14RC.
Defining the RC-3TB Remote Control Panel (Optional) 5 Defining the RC-3TB Remote Control Panel (Optional) Figure 3 and Table 3 define the RC-3TB.
Defining the RC-3TB Remote Control Panel (Optional) (see Table 4) determines which of the 12 pushbuttons on the SL-14RC are emulated by pushbuttons 2 and 3 on the RC-3TB.
Connecting the SL-14RC Master Controller 6 Connecting the SL-14RC Master Controller To connect 1 the SL-14RC as shown in the example in Figure 4: Figure 4: Connecting the SL-14RC Master Controller 1. Connect the RELAY terminal block connectors as follows: Connect RELAY 1 to the lighting system Connect RELAY 2 to the screen 2. Connect the I/O port to a motion detector. 3.
Connecting the SL-14RC Master Controller Connect RS-232 port 1 to the projector Connect RS-232 port 3 to the plasma display 5. Connect the Ethernet port to a network. 6. Connect the K-Net port to the input of the first RC-3TB Remote Control Panel (see Section 6.3). 7. Connect the output of the first RC-3TB Remote Control Panel to the input of the second RC-3TB Remote Control Panel (see Section 6.3.1). 6.
Connecting the SL-14RC Master Controller The wiring from a K-Net port to a single RC-3TB is shown in Figure 6. Figure 6: K-Net to RC-3TB Connection 6.3.1 Terminating RC-3TB Remote Control Panels If only one RC-3TB is connected, it must be terminated and the termination on the SL-14RC is turned off (see Section 6.3.1). When viewed from above and the rotary switch is to the left of the termination switch, slide the termination switch to the left as shown in Figure 6.
Operating the SL-14RC Master Controller Connections to an SL-14RC or to another RC-3TB can be made to either connector block as the connector blocks have identical functionality. 7 Operating the SL-14RC Master Controller You can operate your SL-14RC using: • Front panel pushbuttons. These are configured using the RC-SV configuration software.
LIMITED WARRANTY Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product.
For the latest information on our products and a list of Kramer distributors, visit our Web site www.kramerelectronics.com where updates to this user manual may be found. We welcome your questions, comments, and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing. Caution Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.
