Owner`s manual

ManualsBrandsSIERRA VIDEO SYSTEMS ManualsComputer equipment2020A

11 10

You MUST conﬁgure the Remington 2020 to the correct Remington ammunition you are using at any

given time. Ammunition can be set using the HUD Console or the Settings feature in the Remington 2020 App.

Use only Remington ammunition types specifically paired with your Remington 2020 as shown in

the table below. All Remington 2020 systems have been designed and characterized using these

types and are programmed with the ballistic solutions for those loads. Use of other ammunition

types will result in decreased accuracy in Advanced Modes.

Any ammunition that is correct for your rifle, as described in the rifle’s owner’s manual, can be used

with your Remington 2020 in Traditional Mode.

The ammunition conﬁgured to the Remington 2020 is

displayed in the HUD as shown.

Type Remington 2020 Digital Optic System

BFI Varminter

223 Remington

M700 SPS Tactical

308 Win

M700 LR

30-06 Sprg

SMK (Match) 69-gr Sierra

MatchKing

RAMAC 27680

168-gr Sierra

MatchKing

RAMAC 21485

168-gr Sierra

MatchKing

RAMAC 21419

CLK (Hunting) 55-gr Premier

AccuTip

RAMAC 29192

150-gr Premier

Core-

Lokt

Ultra Bonded

RAMAC 29118

180-gr Premier

Core-

Lokt

Ultra Bonded

RAMAC 29004

TSX (Alternative) 55-gr Barnes

™

VOR-TX

TSX

RAMAC 21520

168-gr Barnes

™

VOR-TX

Tipped TSX

RAMAC 21541

168-gr Barnes

™

VOR-TX

Tipped TSX

RAMAC 21565

Barnes, Core-Lokt, Premier, TSX, Ultra Bonded, and VOR-TX are trademarks of RA Brands, L.L.C.. Sierra and Matchking are trademarks ofSierra Bullets, L.P.

Zeroing

Your Remington 2020 Digital Optic System has been zeroed at the factory. If additional adjustments are

needed they can be made using the HUD Console.

How to adjust zero

Example: Your bullet consistently hits 1 inch to the right of your aim point at a 100 yard target. You need to

move the point of impact 1 inch left to correct.

1. Press and hold the Mode button for 2 seconds to enter the HUD Console (or launch the Remington 2020

app and connect to your Remington 2020).

2. Scroll down to highlight Zeroing L-R (Left-Right) using the Zoom rocker button.

3. Press Left on the Wind rocker button to adjust zeroing setting to read “L 1.0 MOA”. This will adjust the point

of impact to the left 1 inch at 100 yards.

4. Press the Mode button to save and exit the HUD Console.

5. Shoot another group to conﬁrm the new zero setting.

Ammunition

Operating Modes

Your Remington 2020 has three modes of operation - Traditional, Advanced TARGETS, and Advanced

MOVERS. Each mode is designed for optimal performance for various shooting requirements.

1. Traditional Mode

Traditional mode is useful for shooting at short ranges where a precision Tag, Track, React (TTR) shot is not

required or you just want to use the laser range ﬁnder to read various ranges while scouting. In Traditional

mode, the Tag button is only used to read and display range and will not tag your target as it will in advanced

modes.

The Traditional mode uses a Mil-dot reticle and has a ﬁxed zero at 100 yards. All advanced features and

related HUD elements are disabled, including the wind button.

This mode is the default and is active within 2 seconds of powering the system on, allowing for rapid use of

the ﬁrearm, if needed. Traditional mode is always available even if the Remington 2020’s Advanced Mode

Lock feature is set to “locked”.

2. Advanced TARGETS Mode

Advanced TARGETS mode is optimized for TTR shots on stationary targets or game that are typically har-

vested while grazing. Ballistic lead for moving targets is not calculated in this mode.

The Advanced modes use an aiming reticle to assist ranging and tag placement. The Tag button reads range

and sets tracking tag with each press and release.

All advanced HUD elements are displayed to provide sensor readings, and most importantly, conﬁrmation of

correct system conﬁgurations including the following:

• Wind Setting must be correctly input.

• Ammunition selected must be correctly conﬁgured in the digital optic system.

• Desired kill zone should be set.

The Remington 2020 Digital Optic System’s Inertial Measurement Unit and ballistics engine handle

everything else so you can focus on tag placement. The cant and inclination of the Remington 2020 are

displayed in the HUD, however the system automatically compensates for both elements by updating the

ﬁring solution in real time.

3. Advanced MOVERS Mode

Advanced MOVERS mode is optimized for TTR shots on moving targets or game that are active or typically

moving when harvested up to speeds of 10 mph.

Tracking and shooting moving targets can be challenging. Depending on range and target velocity, the

amount of target lead can be 20 feet or more. The Remington 2020 knows the target velocity (displayed

in the HUD) and takes care of the target lead when it sets the ballistics for the moving target. With the Rem-

ington 2020, you engage a mover just as you would engage a static target. Even though the HUD gives the

appearance of aiming directly at the target, the gun barrel is actually pointing in front of the target to provide

the proper lead.

Tagging a Mover – A moving target can be tagged either while the target is stationary or while it is moving.

Tracking Movers – As moving targets move behind brush or other obstacles, track will be lost. If a moving

target turns or changes orientation, the tag may drift off of the original tag point requiring the shooter to reset

the tag. If your target is in a herd of animals, it is possible for the tag to jump to another animal requiring the

shooter to reset the tag point.

Operating your Remington 2020