Owner`s manual

9 8
Temperature - Manually Set
When the Remington 2020 is first powered on, it is set to automatically sense the air temperature. Tem-
perature can also be manually set using the HUD Console in cases where the temperature of the air along the
bullet’s flight path is different from that at the shooter’s position.
Sun Shield
• Daylight
The front sun shield is designed to reduce glare and is required for
optimal daytime use.
• Dawn/Dusk
The front sun shield contains a cut filter that, when removed, will enhance
visibility in very low light conditions, generally around dawn and dusk.
If the HUD image becomes RED after removing sun shield, the available
light is too bright and the sun shield should be re-attached.
The HUD Console enables the user to adjust advanced settings within the Remington 2020 HUD. This
includes Temperature, Kill Zone, Ammunition, and Zero.
To Enter the HUD Console:
1. Press and HOLD the Mode button for 2 seconds to bring
up the HUD Console.
2. Press the Zoom button [Up/Down] to select the function
you want to edit.
3. Press the Wind button [Right/Left] to modify current setting.
4. Press the Mode button again to save changes and exit the
HUD console.
HUD Console
Kill Zone
The kill zone is the point of impact tolerance the shooter sets for when the firing solution turns red, indicating
when to fire. A larger kill zone will allow quicker alignment of firing solution with the tag, however accuracy
may be reduced depending on the skill of the shooter.
Example 1 - Aligning the firing
solution and tag with a small kill
zone requires precise alignment
to cause the reticle to turn red.
Example 2 - Aligning the firing
solution and tag with a large kill
zone (larger area for alignment)
will be easier to cause the reticle
to turn red.
small kill zone
When to change kill zone setting
The size of the kill zone affects the preci-
sion and time it takes to react to a tagged
shot as described in previous examples.
The default kill zone is set to 2.0 MOA,
however the skill of the shooter will also
affect the ability to quickly make tagged
shots at various kill zone sizes.
The system’s kill zone can be set between
0.1 MOA up to 4.0 MOA
MOA to Inches
The chart to the right shows the conver-
sion of MOA to Inches at various ranges.
Rule of thumb: 1 MOA is about 1” for every
100 yards of range.
1 MOA equals approx. 1 Inch at 100 Yards
1 MOA equals approx. 5 Inches at 500 Yards
YARDS
100 200 300 400 500
MOA INCHES
0.1 0.10 0.21 0.31 0.42 0.52
0.2 0.21 0.42 0.63 0.84 1.05
0.3 0.31 0.63 0.94 1.26 1.57
0.4 0.42 0.84 1.26 1.68 2.09
0.5 0.52 1.05 1.57 2.09 2.62
0.6 0.63 1.26 1.88 2.51 3.14
0.7 0.73 1.47 2.20 2.93 3.67
0.8 0.84 1.68 2.51 3.35 4.19
0.9 0.94 1.88 2.83 3.77 4.71
1.0 1.05 2.09 3.14 4.19 5.24
2.0 2.09 4.19 6.28 8.38 10.47
3.0 3.14 6.28 9.42 12.57 15.71
4.0 4.19 8.38 12.57 16.75 20.94
The kill zone setting is displayed at
the top center of the HUD.
Note: The Remington 2020 will generally provide adequate imaging starting at dawn and ending at dusk. In
some states it is allowable to hunt for brief periods before dawn and after dusk. Depending on topography
and direction, you may or may not have adequate light before dawn and after dusk for hunting.
Installing and removing sun shield
To install, align the tabs on the sun shield with the notches in the lens barrel, press to seat and rotate clockwise
until it securely locks into position.
To remove, rotate the sun shield counterclockwise to disengage the locking tabs and pull the shield straight
out of the lens barrel.
Video/Audio Recording
The Remington 2020 records 2 hours of video with audio and takes
snapshots of all of your amazing shots.
Record time remaining is displayed in the upper right corner of the HUD.
When selected in the settings, every time the Tag button is pressed, a video begins recording and stops
recording when the Tag button is pressed again.
If a tagged shot is fired, a recording plus a shot photo will be stored.
Video automatically stops recording 10 seconds after each shot is fired. The post-shot recording time can be
adjusted using the Remington 2020 app.
A “Video Full” message is displayed in the HUD when on-board memory is full. You will need to download or
delete videos before additional recording can continue.
Operating your Remington 2020
Examples of when the temperature may need to be manually set.
• If you are shooting from a hunting blind where the temperature in
the blind is significantly different than the target’s location.
• Solar radiation from direct sunlight onto the digital optic system can
cause the temperature sensor to provide an inaccurate reading.
The temperature is displayed in HUD at bottom right and indicates if Auto
or Manually set.
Once the temperature has been manually set, you must power off and
power on the digital optic system to return to automatic temperature
sensing.
large kill zone