Owner`s manual

7 6
Operating your Remington 2020
Power Button
Press the Power button to turn on the digital optic system.
Power button LED and HUD will turn on.
Note: The Remington 2020 will boot up in Traditional mode within 2
seconds. It may take up to 15 seconds before all buttons are active and
Advanced modes can be selected.
Power O
Press and hold the Power button for 3 seconds to turn off the digital
optic system.
Power On/ Wi-Fi On
When the Remington 2020 is powered on, press the Power button to
turn on the Wi-Fi function. The Wi-Fi icon will appear in the HUD.
To turn off the Wi-Fi function, press the Power button. The Wi-Fi icon
will turn off in the HUD.
The number of connected smart devices is displayed next to the Wi-Fi
icon. A maximum of 3 devices can be connected simultaneously.
Mode Button
Press the Mode button to toggle between Traditional, Advanced TAR-
GETS, and Advanced MOVERS modes. The Remington 2020 will always
power up in Traditional mode. (See Operating Modes section for details.)
Press and hold the Mode button for 2 seconds to enter the HUD Console
settings. (See HUD Console section for details.)
Zoom Rocker
Press the Zoom button forward to zoom in from 3x to 21x.
Press the Zoom button backward to zoom out.
The current zoom level is displayed at the bottom center of the HUD.
HUD Focus
The Heads Up Display must be focused prior to adjusting scene focus to
obtain maximum clarity. Rotate the focus ring at the back of the digital
optic system clockwise or counterclockwise while looking at the smallest
text elements within the Heads Up Display. Once they are in focus to
your vision, no further HUD focus adjustments should be required.
Scene Focus
Once the HUD Focus has been set, the Scene Focus knob should be the
only focus adjustment needed while using your Remington 2020.
Rotate the Scene Focus knob clockwise or counterclockwise after zoom-
ing in or out to adjust image clarity.
Wind Input Rocker (Advanced Modes only)
Shooter MUST assess wind conditions, and input if necessary prior
to making a TTR shot.
Press the Wind rocker to set wind to current conditions in half mile per
hour (MPH) increments right or left relative to the orientation of the
barrel. For example, if wind is blowing right to left, setting should show
arrow pointing left.
The current setting will be displayed in the HUD.
Tag Button
• Traditional Mode
Place the blue ellipse where you desire to range and press the Tag button
for
1
/
2
second to read the range to target.
• Advanced Modes
Press the Tag button for
1
/
2
second to place a tag on your target at the
desired point of impact. The range is automatically read and updated in
the HUD.
Press the Tag button again to cancel tag. Tag as many times as you want
to get the most precise shot placement.
If you hold the tag button longer than a half second, the image will
stabilize to assist you in placing your tag in the desired position.
USB Port
The USB port has been designed to interact only with approved Reming-
ton accessories. Do not insert anything in the USB port that is not an ap-
proved Remington accessory. To maintain water resistance of the DOS,
always keep the USB port cover inserted when the port is not being used.
Accessory Jack
The accessory jack has been designed to interact only with approved
Remington accessories. Do not insert anything in the accessory jack that
is not an approved Remington accessory.
Eye Guard
The eye guard is designed primarily to shield the HUD from the sun, al-
lowing clear visibility of the display.
The eye guard is also designed as a stand-off from the digital optic
system and should remain attached to the Remington 2020 to
reduce the probability of injury.
The eye guard is a safety device and is not a guarantee against
injury.
Installing and removing eye guard
To install, slide the eye guard over the rear HUD optic until it seats securely.
To align the eye guard to fit your eye, rotate as needed.
To remove, pull the eye guard until it slides off from the optic.