High Precision, 2-color Display Digital Pressure Switch Series ZSE30/ISE30 ZSE ISE PSE Z I SE3 PS Z I SE 12 ZSP ISA2 IS ZSM PF2 IF Data With One-touch fittings are newly introduced.
-color digital display allows you to choose the setting according to your application requirements. 4 different display settings are available. ∗ This photo shows 2 display colors simultaneously for product presentation purposes. In actual application, only one color is displayed at a time.
Space-saving improvement Economical use of space Old Model ZSE4E ISE4E Each displa y required its own pa Display calibration nel openin g. Old Model 40 ZSE ISE PSE Z I 126 PS New Model New Model ZSE30 ISE30 SE3 Z I Just one p anel openin g is required fo r st displays, w ackable hich can b e mounted e ithe or vertically r horizontally . SE 12 ZSP ISA2 This function allows uniformity in the numbers displayed. IS 34.
® High Precision, 2-color Display Digital Pressure Switch Series ZSE30/ISE30 How to Order Option 1 Without lead wire Nil Lead wire with connector (Lead wire length: 2 m) L For positive pressure ISE30 01 25 M For vacuum/low pressure ZSE30 01 25 M Option 2 Piping specifications 01 R 1/8 (With M5 female thread) T1 NPT 1/8 (With M5 female thread) C4H ø4 One-touch fitting ø5/32" One-touch fiting C6H ø6 One-touch fitting N7H ø1/4" One-touch fitting C4L ø4 One-touch fitting ø5/32" One-touc
High Precision, 2-color Display Digital Pressure Switch Series ZSE30/ISE30 Specifications ZSE30 (Vacuum/Low pressure) ISE30 (Positive pressure) Rated pressure range –100.0 to 100.0 kPa 0.000 to 1.000 MPa Regulating pressure range –101.0 to 101.0 kPa –0.100 to 1.000 MPa Proof pressure 500 kPa 1.5 MPa Min. regulating unit 0.2 kPa 0.
Series ZSE30/ISE30 Setting Pressure setting Press the SET button. Enter the set value of the pressure to perform switch output. Measuring mode Press the SET button. Initial setting Set the output type, response time, and display color switching. Press the SET button and hold for 2 sec. or longer. Measuring mode Detects and displays the pressure and performs switch operations. Other functions such as the value clear function can be set according to the application purpose. Press the SET button.
High Precision, 2-color Display Digital Pressure Switch Series ZSE30/ISE30 Pressure setting Auto preset setting Manual setting Press the SET button in the measuring mode to display the set value. and the current set value blink alternately. PRESSURE OUT Normally Open Alternately displayed PRESSURE 1. Auto preset preparation mode While in the measuring mode, press the SET button to activate the auto preset preparation mode, and will be displayed.
Series ZSE30/ISE30 Setting Function setting Display calibration Key lock function During measuring mode, press the SET and DOWN buttons simultaneously and hold for 2 seconds or longer. and current measured value will be displayed. Press the UP or DOWN button to change the set value. If there is no button operation for more than 2 seconds after changing the set value, the display mode returns to displaying and the current measured value.
High Precision, 2-color Display Digital Pressure Switch Series ZSE30/ISE30 Description Indication light (Green) LCD display Displays the switch operation status. PRESSURE MPa UP button OUT SET Use this button to change the mode or increase the ON/OFF set value. It also allows you to switch to the peak value display mode. SET button Use this button to switch the mode and set the set value.
Series ZSE30/ISE30 Dimensions 30 25 8 9.5 Lead wire with connector 3.6 M5 x 0.8 Wi dth SET 01: R 1/8 T1: NPT 1/8 C øB øB Straight Elbow With One-touch fitting 15 10 42.5 With bracket 4.2 sf lat s1 2 A A 3 22 30 20 20 25 1.8 30 45 SMC 16-2-10 ac ros 1.5 35 20 ±0.1 SMC OUT 2-M3 x 0.5 Thread depth 4 MPa 10 PRESSURE 20 ±0.1 35 One-touch fitting size ø4, ø5/32" ø6 ø1/4" Straight A B 14.4 11.2 (mm) Elbow C B A 10.4 18 20 22.4 12.8 20 22.8 13.2 20.
High Precision, 2-color Display Digital Pressure Switch Series ZSE30/ISE30 Dimensions Panel mount ZSE ISE PSE 7.2 17.8 8 Z I 9.5 34.5 Z I R4 MPa R4 ZSP ISA2 SET SE 12 .5 .5 OUT SE3 PS 21 PRESSURE 47.8 MADE IN JAPAN IS 8.75 Panel thickness 0.5 to 6 ZSM PF2 IF Panel mount adapter + Front protective cover Data 42.4 11 17.8 8 9.5 34.5 Panel thickness 0.
Series ZSE30/ISE30 Dimensions Panel fitting dimension Multiple (2 pcs. or more) horizontal mounting PRESSURE PRESSURE MPa OUT SET SET 31 x n pcs. + 3.5 x (n pcs. – 1) 24 and up 0 31 –0.4 0 31 –0.4 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN Multiple (2 pcs. or more) vertical mounting 0 31–0.4 PRESSURE 24 and up MPa PRESSURE SET MPa OUT SET PRESSURE MPa 31 x n pcs. + 3.5 x (n pcs.
Series ZSE30/ISE30 Specific Product Precautions 1 Be sure to read before handling. Handling Operating Environment 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling. Although the body of the sensor may not be damaged, the internal parts of the sensor could be damaged and lead to a malfunction. 2. The tensile strength of the cord is 35 N. Applying a greater pulling force on it can cause a malfunction. When handling, hold the body of the sensor––do not dangle it from the cord. 3.
Series ZSE30/ISE30 Specific Product Precautions 2 Be sure to read before handling. Connection/Removal of Connector Piping • To connect the connector, insert it straight while pinching the lever, and then push the lever into the jack of the housing and lock it. • To remove the connector, pull it straight out while applying pressure with your thumb to the lever and unhooking it from the jack. • Cut the tube perpendicularly.
Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices. Caution : Operator error could result in injury or equipment damage. Warning : Operator error could result in serious injury or loss of life.
Common Precautions Be sure to read before handling. For detailed precautions on every series, refer to main text. Selection Warning 1. Confirm the specifications. Products represented in this catalog are designed for use in compressed air appllications only (including vacuum), unless otherwise indicated. Do not use the product outside their design parameters. Please contact SMC when using the products in applications other than compressed air (including vacuum). Mounting Warning 1.
Quality Assurance Information (ISO 9001, ISO 14001) Reliable quality of products in the global market To enable our customers throughout the world to use our products with even greater confidence, SMC has obtained certification for international standards “ISO 9001” and “ISO 14001”, and created a complete structure for quality assurance and environmental controls. SMC products pursue to meet its customers’ expectations while also considering company’s contribution in society.
SMC Product Conforming to Inter SMC products complying with EN/ISO, CSA/UL standards are supporting CE Mark The CE mark indicates that machines and components meet essential requirements of all the EC Directives applied. It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and components are exported to the member Nations of the EU.
SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards. Mark of compliance for CSA/UL Mark of compliance for CSA CSA Standards & UL Standards UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric products, and are defined to mainly prevent danger from electric shock or fire, resulting from trouble with electric products.
SMC’s Global Service Network America Europe U.S.A. SMC Corporation of America 3011 North Franklin Road Indianapolis, IN 46226, U.S.A. TEL: 317-899-4440 FAX: 317-899-3102 U.K. SMC Pneumatics (U.K.) Ltd. Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN, Backinghamshire, U.K. TEL: 01908-563888 FAX: 01908-561185 CANADA SMC Pneumatics (Canada) Ltd.
SMC’s Global Service Network Europe Oceania/Asia FINLAND SMC Pneumatics Finland OY PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland TEL: 09-8595-80 FAX: 09-8595-8595 AUSTRALIA SMC Pneumatics (Australia) Pty.Ltd. 14-18 Hudson Avenue Castle Hill NSW 2154, Australia TEL: 02-9354-8222 FAX: 02-9894-5719 NORWAY SMC Pneumatics Norway A/S Vollsveien 13C, Granfoss Næringspark N-1366 LYSAKER, Norway TEL: 67-12-90-20 FAX: 67-12-90-21 NEW ZEALAND SMC Pneumatics (New Zealand) Ltd. 8C Sylvia Park Road Mt.
