Environmental Declaration

EPD - Type II
Based on ISO 14021
Building Parts
CuZnPb Armature variant
Steel stainless Transducer cup + Cover 6g
Steel stainless reflector 6g
Steel >5% alloyed magnetic shield 4g
Steel stainless screws, plates 7g
Steel >5% alloyed screws, plates 3g
Steel <=5% alloyed Seal + Wire 2g
Cu / Al / Polyester fleece / Silicone Cable / Wire 38g
Cu / TPE-U temperature sensor DS 27.5 mm 1.5 m variant
Piezoceramic (PZT) transducer 1g
Lithium-Thionylchloride Batteries variant
Cu / TPE-U temperature sensor PS 45 mm 1.5 m variant
FR4; halogenated; solder SnAgCu main PCB 44g
FR4; halogenated; solder SnAgCu M-Bus 12g
Passive components variant
Active components variant
ICs variant
Wei
g
hts in brackets are alread
y
included in com
p
onents declared under materials.
(p
art of the assembled PCB
)
*Variant parts list
[g]
Total weight of device
Adapter Sensor PS
Armature
temperature sensor DS 27.5 mm
Batteries
temperature sensor PS 45 mm 1.
5
Fire load [MJ]
Special components
(
part of th
e
Passive components [pcs]
Active components
ICs
Comments
A5W00080753A-AA-001 14.01.2020
S55561-F277
893
S55561-F276
803
S55561-F274
864
S55561-F270
786
S55561-F272
818
355
S55561-F269
830
355
17
90
311
157
8
6
10
6
401
90
8
17 17
157
10
S55561-F271
876
157
90
8
10 9
4
17
74
157
8
66
4
S55561-F273
774
17
74
311
8
157
9
6
4
401
74
9
157
8
6
3417
S55561-F275
847
90
355 311
34
10
90
10
34
401
90
10
EU-directive 2011/65/EU (RoHS)
The device does not contain substances in concentrations and applications banned under the EU RoHS Directive, including the 4 phthalates added to
Annex II in 2015.
The device contains the following substances of the candidate list according to Article 59 (1, 10) of the regulation (EC) No. 1907/2006 concerning the
Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) in concentrations above 0.1 % w/w. Contained REACH candidate
substances, including those which will become known at a later date, are listed on the delivery note.
Lead titanium zirconium oxide, CAS-Nr.12626-81-2; Lead, CAS-Nr.7439-92-1
(Status according to the creation date of this document.)
Please contact your local Siemens branch office to get further information on environmental aspects and disposal.
Legal Disclaimer: This declaration is for information purpose only.
Landis+Gyr GmbH therefore does not assume liability for any error or for any consequences which may arise from the use of this information to the maximum extent under
the law.
This Environmental Product Declaration does not constitute a guarantee of the composition of a product, neither does it guarantee that the product will retain a particular
composition for a particular period.
Special components
(part of the assembled PCB)
Regulation (EC) No. 1907/2006 (REACH)
The device is low-halogen with exception of:
Cableparts (ETFE isolation); damping body of transducers (FKM); PCB (TBBA)
Others
The device is classified as waste electronic equipment in terms of the European Directive 2012/19/EU (WEEE) and must
not be disposed of as unsorted municipal waste. Regarding disposal, use the systems setup for collecting electronic
waste.
Observe all local and applicable laws.
Disposal
PCBAs (Printed Circuit Board
assembled)
Metals
Restricted Page 2/2