Installation Instructions

ManualsBrandsSiemens ManualsRoom controlsÉmetteur-récepteur sans fil (TTX) pour contrôleur d’équipement terminal (TEC) Installation Instructions

Table Of Contents

TALON® Logo

Document No. 563-066

November 2, 2015

Wireless Room Sensor (WRS)

Item Number 563-066, Rev. DA Page 1 of 4

Figure 1. Wireless Room Sensor (Full-Featured).

Product Description

Wireless Room Sensors eliminate the need to run

wire between Terminal Equipment Controllers

(TECs) and their respective room temperature

sensor. The sensor communicates wirelessly with

the TEC using a Room Sensor Transceiver (RSX)

mounted at the TEC.

Product Numbers

TALON

Logo

QAA2391.EWTC Wireless Room Sensor (WRS) –

Sensing only

QAA2391.DWTC Wireless Room Sensor (WRS) –

Sensing with temperature

display

QAA2391.FWTC Wireless Room Sensor (WRS) –

Sensing with override, setpoint,

and temperature display

No Logo

QAA2391.EWNC Wireless Room Sensor (WRS) –

Sensing only

QAA2391.DWNC Wireless Room Sensor (WRS) –

Sensing with temperature

display

QAA2391.FWNC Wireless Room Sensor (WRS) –

Sensing with override, setpoint,

and temperature display

Accessories

563-207 Auto-binding cable (to bind

WRS/RSX pair)

544-643A RTS passkey (to change display to

DIAG mode)

N/A Replacement 3.6 Volts lithium AA

battery –SAFT Part Number

LS14500BA (See Field Purchasing

Guide.)

540-143 Laptop computer cable

(RJ-11 to DB-9)

141-570 Lockable Thermostat Guard,

vented clear plastic.

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 563-066 November 2, 2015 Wireless Room Sensor (WRS) Accessories 563-207 544-643A N/A 540-143 Figure 1. Wireless Room Sensor (Full-Featured). Product Description Wireless Room Sensors eliminate the need to run wire between Terminal Equipment Controllers (TECs) and their respective room temperature sensor. The sensor communicates wirelessly with the TEC using a Room Sensor Transceiver (RSX) mounted at the TEC.
PAGE 2
Document No. 563-066 Installation Instructions November 2, 2015 Required Tools • Phillips screwdrivers, sizes 1 and 2 • Medium and small flat-blade screwdrivers Binding Using HMI Commands To bind your WRS to its associated RSX using HMI commands, follow these steps: • 1/16” hex key 1. • Medium-duty electric drill and 3/16-inch (4.8 mm) drill bit Connect a PC cable (540-143) from a computer to the RJ-11 port on the bottom of the WRS. 2.
PAGE 3
Document No. 563-066 Installation Instructions November 2, 2015 • Away from drafts caused by doors, windows, outside walls, air registers, return air plenums, and so on. • Away from heat sources such as strong lights, fireplaces, direct sunlight, and son on. • On an inside wall, about 5 feet (1.5 m) above the finished floor. 2. Mount the WRS base plate to the wall. • If used, leave sufficient room to install the Lockable Thermostat Guard. See the Lockable Thermostat Guard Technical Instructions (155-723).
PAGE 4
Document No. 563-066 Installation Instructions November 2, 2015 • Consult the dealer or an experienced radio/TV technician for help. Section 7.1.5 of RSS-GEN Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: This device complies with Part 15 of the FCC rules.