Specifications

ManualsBrandsSiemens ManualsMedia ConverterSINAMICS G150

SINAMICS G150

Drive converter cabinet units

75 kW to 1500 kW

3/5

Siemens D 11 · 2008

Function

AOP30 Advanced Operator Panel

An AOP30 Advanced Operator Panel is located in the cabinet

door of the converter for operation, monitoring and commission-

ing tasks.

The AOP30’s two-stage safety concept prevents unintentional or

unauthorized changes to settings. Operation of the drive from

the operator panel can be disabled by a password ensuring that

only parameter values and process variables can be displayed

on the panel. The OFF key is factory-set to active but can also

be deactivated by the customer. A password can be used to pre-

vent the unauthorized modification of converter parameters.

The user is guided through the screens for commissioning the

drive by the menu-driven display. Only 6 motor parameters

(which can be found on the motor rating plate) have to be en-

tered when the AOP30 is commissioned for the first time. The

control is then optimized automatically to fine-tune the converter

to the motor.

English, French, German, Italian, Spanish and Chinese are

stored on the CU320 Control Unit’s CompactFlash card as oper-

ator panel languages. The desired language must be down-

loaded to the AOP30 prior to commissioning. Russian, Polish

and Czech are available in addition to these standard panel lan-

guages. These can be downloaded free of charge from the In-

ternet under the following link:

http://support.automation.siemens.com/

The following pictures show examples of plain-text displays in

various operating phases.

First commissioning is carried out using the operator panel.

Only 6 motor parameters have to be entered:

power, speed, current, cos phi, voltage and frequency of the

motor.

This information can be found on the motor rating plate and is

entered into the screens on the display by following a short,

menu-driven procedure. The cooling method of the motor must

be entered in addition.

The next screen contains the parameter values that are used to

automatically optimize the control.

During operation, current data are output on the display as ab-

solute values such as setpoint and actual values , or it is possible

to parameterize up to 3 process variables as a quasi-analog bar

display.

Any alarms which occur are signaled by flashing of the yellow

"ALARM" LED, faults by lighting up of the red "FAULT" LED.

There is also an indication of the cause displayed in plain text on

the display’s status line.

Service /Commissioning

Drive commissioning

Device commissioning

AOP settings

AOP diagnosis

Help

G_D011_en_00047

Back Select.

Motor data

Back

p0304 MOT.U_rated 400.0 V

p0305 MOT. I_rated 405.0 A

p0307 MOT.P_rated 235.0 kW

p0308 MOT.CosPhi_ rated 0.870

Help Change OK

G_D011_en_00048

G_D011_en_00049

Basic commissioning

Back

p0700 Pre-assignment BI S/G150 TM 32

p1000 Default DI n_set TM 31 AIO

p1080 Minimum speed 0.000 rpm

-1

p1082 Maximum speed 1500.000 rpm

-1

Help Change Further

Operation 12:25:30

Nset

Fout

P act

Nact:

1450.0 rpm

1450.00

48.50

2700

410

rpm

1450.0 rpm

385.3 V

748

Nact

Imot

Vout

G_D011_EN_00011b

0% 50 100%

G_D011_EN_00012b

Operation 12:25:30

NSET 1465.50 rpm Pact 410 kW

Fout 48.50 Hz Vout 385.3 V

Imot

748 A

Nact

1465 rpm

(3 : Vector) Current fault in

F 07901 Motor overspeed

Help Alt Back Ack.

G_D011_en_00050

G_D011_en_00051

Motor overspeed

Fault val = 000000007 00000007 (hex)

Cause:

The maximum permisible positive or

negative speed has been exceeded.

The maximum permissile positive speed

is calculated as follows:

Back