SIMATIC PC Adapter TS Adapter Quick Reference Guide Edition 01/2003 A5E00078070-02
Exclusion of Liability We have checked the contents of this manual for agreement with the hardware and software described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement. However, the data in this manual are reviewed regularly and any necessary corrections included in subsequent editions. Suggestions for improvement are welcomed. Technical data subject to change.
Contents 1 Product Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 MPI/DP Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 Prerequisites for Operation . . . . . . . . . . . . . . . . . . . . . . . 5 5.1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC/MPI Cable ii Kurzanleitung PC/TS Adapter A5E00078070-02
Quick Reference Guide 1 PC/TS Adapter Product Definition The adapter is available as: S PC adapter 6ES7 972-0CA2x-0XA0 or S TS adapter 6ES7 972-0CA3x-0XA0 Note Where ’adapter’ is referred to below, the text applies to both variants. The PC adapter connects a PC to the MPI/DP interface (Multipoint Interface) via the serial COM port of an S7/M7/C7 system. This does not require a PC slot, that is, the adapter is also suitable for use in non-expandable PCs such as notebooks. 1) 19.2/38.
PC/TS Adapter Quick Reference Guide With ’direct connection’, the TS adapter allows you to link programming devices/PCs with S7/M7/C7 systems. With this setup, the TS adapter corresponds in functionality to the PC adapter. With ’modem connection’, the TS adapter enables you to link programming devices/PCs with S7/M7/C7 systems over the telephone network. Direct Connection 19.2/38.4 kb 1) RS232 TS adapter S7/M7/C7 system PC RS232 COM1... Switch MPI/DP 19.2/38.
Quick Reference Guide PC/TS Adapter Adapter MPI/DP connector LED “POWER” LED “ACTIVE” RS232 connector Figure 1-3 Switch “19.2/38.4 kbps” Adapter The two adapter types differ with respect to the location of the MPI/DP parameters: S The MPI/DP parameters for the PC adapter are set in “Set PG/PC interface”. When opening an online display for the first time, ther parameters are transferred to the PC adapter.
PC/TS Adapter 2 Quick Reference Guide Package Components S Adapter S Quick Reference Guide S Mounting assembly (TS adapter only) 3 Accessories (not part of the adapter package) S RS232 cable, 6 meters in length 6ES7 901-1BF00-0XA0 (required to operate the PC adapter and to operate the TS adapter in direct connection only). 4 MPI/DP Network A maximum of 32 nodes can be interfaced to an MPI/DP network segment. The total cable length may not exceed 50 meters.
Quick Reference Guide PC/TS Adapter 5 Prerequisites for Operation 5.1 Hardware PC/programming device with a free COM port (COM1 or COM2, 9-pin COM connection). Appropriate adapters for other connector combinations are available in specialist shops, for example 9-pin to 25-pin subminiature D connector.
PC/TS Adapter Quick Reference Guide 6 Connecting the Adapter 6.1 Safety-related Guidelines Qualified Personnel A device/system may only be commissioned or operated by qualified personnel. Qualified personnel as referred to in safety guidelines in this document are persons authorized to energize, de-energize, clear, ground, and tag circuits, equipment and systems in accordance with established safety practice. For a detailed description of the safety-related guidelines, please refer to the Appendix.
Quick Reference Guide 6.2 PC/TS Adapter General Remarks MPI/DP side: Adapter and S7/M7/C7 system each represent one network node. In networks comprising two nodes (adapter and S7/M7/C7 system), the adapter is plugged directly into the S7/M7/C7 system’s MPI/DP port; in networks consisting of more than two nodes, the adapter is plugged into a Profibus connector’s “PG port” (SINEC L2 bus connector); for details, please refer to catalog IK10.
PC/TS Adapter Quick Reference Guide As the adapter receives its power supply via the MPI/DP interface, only those interfaces can be used which provide 24 V DC and 5 V DC with the voltages and currents specified in the table in the ”Technical Specifications” (Chapter 7). Therefore a connection at the free end of a PROFIBUS cable is not possible.
Quick Reference Guide PC/TS Adapter 9-pin subminiature D: Signal: DCD RXD TXD DTR GND DSR RTS CTS RI 1 2 3 4 5 6 7 8 9 Shield NC NC Shield NC Shield Connector casing Figure 1-8 ! 9-pin subminiature D: Shield NC Signal: 1 2 3 4 5 6 7 8 9 DCD RXD TXD DTR GND DSR RTS CTS RI Connector casing RS232 Cable 6ES7 901-1BF00-0XA0 Warning The RS232 cable listed under Point 3 (Accessories) ensures that EMC requirements are met.
PC/TS Adapter 6.3 Quick Reference Guide Pin Configuration The MPI/DP connector has the following pin configuration: 5 1 6 Figure 1-9 9 MPI/DP Connector Signals Pin No. 1 2 Abbreviation NC M24V 3 LTG_B 4 RTSAS RTSAS Control signal for receive data current; the signal is active ‘1’ when the directly connected interface module is transmitting.
Quick Reference Guide Pin No. 7 Abbreviation P24V 8 LTG_A 9 RTS_P G Shield PC/TS Adapter Description 24V supply’s +24V line, supplies adapter electronics via DC/DC converter (PC potential area) Data line A Adapter’s RTS output signal. The signal is ‘1’ when the adapter is transmitting. On connector casing* Input/ Output Input Input/output Output * The shield is interconnected with the RS232 connector via the adapte casing’s shield.
PC/TS Adapter Quick Reference Guide The RS232 connector has the following pin assignments: 5 1 6 Figure 1-10 9 RS232 Connector (PC-compatible) Signals Pin No.
Quick Reference Guide 6.4 PC/TS Adapter Connection Procedures Start Switch PC/ modem off Establish cable connection on RS232 side of the adapter (see 6.2 “General”, RS232 side) (See 6.2 “General”, MPI/DP side) => Microprocessor in adapter starts to work and switches the Power LED to constant light after blinking three times (see also 6.
PC/TS Adapter 6.5 Quick Reference Guide Function and Operation of the Switch The switch is used for setting the transmission rate (19.2 kbps or 38.4 kbps) on the RS232 side of the adapter variant in direct connection. It has no function with modem connection. The transmission rate set with the switch must agree with the rate parameterized for the PC in “Set PG/PC interface”. Note A Transmission speed of 38,4 kbit/s is only possible using STEP 7 Version 3.1 or higher.
Quick Reference Guide PC/TS Adapter The switch is operated only infrequently and is recessed so that it cannot be operated inadvertently. See Figure 1-11 for the location of the switch. Both switch positions are labeled on the underside of the unit. To operate the switch, please use a ball-point pen (“retractable ball-point”) up to a diameter of 1.7 mm or a blunt instrument of the same size.
PC/TS Adapter 7 Quick Reference Guide Technical Specifications All required specifications are listed in the table below. Designation Technical Specifications PC adapter Order number PC Adapter TS Adapter Dimensions 108 mm x 50 mm x 24 mm (4.25 in. x 1.96 in. x 0.94 in.) (L x W x H) Weight Approx. 0.15 kilograms Interfaces to S7/M7/C7 to PC 6ES7 972-0CA2x-0XA0 6ES7 972-0CA3x-0XA0 RS485 (bis max. 1,5 Mbit/s) RS232 (19.2 kbps / 38.
Quick Reference Guide Designation PC/TS Adapter Technical Specifications Electromagnetic compatibility (EMC) Emitted interference Limit class B to EN 55022 = CISPR 22 Interference immunity on signal lines "2kV Interference immunity against discharging of static electricity "6kV Highfrequency radiation 10 V with 80% amplitude modulation at 1 kHz, 10 kHz - 80 MHz (to ENV 50141) 10 V/m with 80% amplitude modulation at 1 kHz, 80 Mhz - 1GHz (to ENV 50140) 10 V/m pulse-modulated 50% load factor at 900
PC/TS Adapter Designation Quick Reference Guide Technical Specifications Mechanical environmental conditions Vibration Operation shipping (adapter packed for transport) Shock operation shipping (adapter packed for transport) Tested to DIN IEC 68-2-6 10 to 58 Hz, amplitude 0.075 mm 58 to 150 Hz acceleration 9.8 m/s2 5 - 9 Hz, amplitude 3.5 mm 9 - 500 Hz, acceleration 9.
Quick Reference Guide 7.2 PC/TS Adapter Features of the PC/TS Adapter Versions PC Adapter Transmission speed V3.0 19.2 Kbps to PC Transmission speed 187.5 Kbps V3.1 V5.0 V5.1 19.2 Kbps 19.2 Kbps 19.2 Kbps and and and 38.4 Kbps 38.4 Kbps 38.4 Kbps 187.5 Kbps 9.6 Kbps 9.6 Kbps to to 1.5 Mbps 1.
PC/TS Adapter Quick Reference Guide TS Adapter V3.0 V5.0 V5.1 V5.2 Transmission speed to PC 19.2 Kbps 19.2 Kbps and 38.4 Kbps 19.2 Kbps and 38.4 Kbps 19.2 Kbps and 38.4 Kbps Transmission speed of Adapter-Modem interface 2.4 Kbps 4.8 Kbps 9.6 Kbps 19.2 Kbps 38.4 Kbps 2.4 Kbps 4.8 Kbps 9.6 Kbps 19.2 Kbps 38.4 Kbps 57.6 Kbps 115.2 Kbps 2.4 Kbps 4.8 Kbps 9.6 Kbps 19.2 Kbps 38.4 Kbps 57.6 Kbps 115.2 Kbps 2.4 Kbps 4.8 Kbps 9.6 Kbps 19.2 Kbps 38.4 Kbps 57.6 Kbps 115.
Quick Reference Guide 8 Approvals 8.1 Approval for USA and Canada PC/TS Adapter UL/CSA approval Important for the U.S.A. and Canada: The characters stamped on a device are indicative of the requirements which that device meets: Underwriters Laboratories (UL) to the UL 1950 standard, Report E11 5352 C Underwriters Laboratories (UL) to the Canadian standard C22.2 No. 950 UL recognition mark Canadian C di Standard S d d Association A i i (CSA) to standard C22.2 No. 950 or C22.2 No.
PC/TS Adapter Quick Reference Guide FM Approval FM approval to Factory Mutual Approval Standard 3611. ! Warning Personal injury or property damage can result. In hazardous areas, personal injury or property damage can result if you close or disconnect an electrical circuit during operation (e.g. plug-in connections, fuses, switches). Do not close or disconnect any live circuits unless explosion hazards can be definitely excluded.
Quick Reference Guide 8.
PC/TS Adapter 24 Quick Reference Guide PC/TS Adapter A5E00078070-02
