Preface SIMATIC Industrial PC SIMATIC HMI IPC677C Operating Instructions Safety 1 Description 2 Planning the use 3 Mounting 4 Connecting Integration into an automation system 7 Operation and configuration 8 Operation 9 Functions 10 11 12 Troubleshooting/FAQs 13 Technical data 14 Dimensional drawings 15 Detailed descriptions 16 Appendix List of Abbreviations/Acronyms A5E02722710-01 6 Commissioning Service and maintenance Alarm, error, and system messages 05/2010 5 A B
Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
Preface Overview Purpose of this manual These operating instructions contain all the information you need for commissioning and operating the SIMATIC IPC677C. It is intended both for programming and testing personnel who commission the device and connect it with other units (automation systems, programming devices), as well as for service and maintenance personnel who install add-ons or carry out fault/error analyses.
Preface Conventions Representation Validity "File" Terminology that appears in the user interface, for example menu commands, tabs, buttons Required input, for example limit values, tag values Path information "File > Edit" Operational sequences, for example, menu commands, shortcut menu commands , + Keys and key combinations The "IPC677C", "control unit" and "computer unit" are uniformly referred to as "device" in these operating instructions.
Table of contents Preface ...................................................................................................................................................... 3 1 2 3 4 5 Safety ...................................................................................................................................................... 11 1.1 Safety guidelines..........................................................................................................................11 1.
Table of contents 6 7 8 6 Integration into an automation system ..................................................................................................... 45 6.1 Overview ..................................................................................................................................... 45 6.2 6.2.1 6.2.2 Device in SIMATIC S7 network................................................................................................... 46 MPI/PROFIBUS-DP network...............
Table of contents 9 10 11 Operation................................................................................................................................................. 75 9.1 Status displays .............................................................................................................................75 9.2 9.2.1 9.2.2 9.2.3 9.2.3.1 9.2.3.2 9.2.3.3 9.2.4 9.2.5 9.2.6 Device with key panel .......................................................................................
Table of contents 12 13 14 15 8 11.8.2 11.8.3 11.8.4 11.8.5 11.8.6 11.8.7 11.8.8 11.8.9 Preventive maintenance............................................................................................................ 111 Replacing the Backup Battery................................................................................................... 111 Removing/Installing the Power Supply .....................................................................................
Table of contents 16 Detailed descriptions ............................................................................................................................. 167 16.1 Motherboard...............................................................................................................................167 16.1.1 Structure and functions of the motherboard ..............................................................................167 16.1.2 Technical features of the motherboard .............
Table of contents 10 SIMATIC IPC677C Operating Instructions, 05/2010, A5E02722710-01
1 Safety 1.1 Safety guidelines WARNING Emergencies In the event of a device fault, interrupt the power supply immediately. Inform the customer service personnel responsible. Malfunctions can occur when the operator controls or power cable are damaged or when liquids or foreign objects penetrate the device. WARNING Following the results of a risk analysis, additional protection equipment on the machine or the system is necessary to avoid endangering persons.
Safety 1.2 General Information High frequency radiation CAUTION Unintentional operating situations High frequency radiation, from cell phones for example, can cause unintentional operating situations under some circumstances. Further information is available in the section "EMC requirements" of the "Technical data" chapter.
Safety 1.2 General Information Transport Unpack the device at its installation location. Transport the device only in the original packaging. Do not transport the device when it is mounted. NOTICE Adhere to these stipulations each time the device is transported, otherwise the guarantee is void. CAUTION Condensation When transporting the device at low temperatures, ensure that no moisture gets on or into the device. This also applies if the device is subjected to extreme changes in temperature.
Safety 1.2 General Information Resistance to chemicals CAUTION Adhere to the information regarding chemical resistance of the panel front. For additional information, refer to the Internet at "Technical Support (http://support.automation.siemens.com)". Enter the article ID 22591016 in the "Search for product information". The available article is displayed. Sources of light NOTICE Position the screen so that it is not subject to direct sunlight or other strong sources of light.
Safety 1.3 ESD directives 1.3 ESD directives What does ESD mean? Almost all electronic modules are equipped with highly integrated components and elements in MOS technology. For technological reasons, these electronic components are very sensitive to overvoltages and, consequently, to electrostatic discharge.
Safety 1.3 ESD directives Do not allow chargeable, highly insulated materials, e.g. plastic films, insulating tabletops, synthetic clothing fibers, to come into contact with ESD components. Place ESD components only on conductive surfaces (work surfaces with ESD surface, conductive ESD foam, ESD packing bag, ESD transport container). Do not expose ESD components to visual display units, monitors or televisions. Maintain a distance of at least 10 cm to screens. Handle flat components only by their edges.
2 Description 2.1 Design of IPC677C Design (1) Computer unit (2) Control unit Figure 2-1 IPC677C Product Brief The device is available with different control units which are distinguished by the size of the display and by the key or touch panel.
Description 2.2 Characteristics of IPC677C Key panel variants ● Color display with backlighting – 12" TFT technology; 800 x 600 resolution – 15" TFT technology; 1024 x 768 resolution – 15" TFT technology; resolution 1024 x 768 pixels, with stainless steel front INOX – 19" TFT technology; 1280 x 1024 resolution ● LEDs for power supply and temperature ● Front-mounted USB 2.0 port for connecting external I/O devices (except INOX). All fronts are also available without USB port accessible from the front.
Description 2.2 Characteristics of IPC677C Basic data Drives and storage media 1 x 3.5" hard disk or 2 x 2.5" hard disk or RAID1 system Capacity see order forms Mass storage DVD drive DVD burner Flash memory Slot for Compact Flash card 1 x Solid State Disk Ports Ethernet 2x 10/100/1000 Mbps (RJ45) PROFIBUS/MPI 12 Mbps (isolated potential, compatible to CP 5611), optional PROFINET 10/100 Mbps (CP 1616 onboard), three RJ45; optional USB External: 4x USB 2.0 high current (max.
Description 2.3 Accessories of IPC677C Optional expansions SIMATIC PC DiagMonitor software ≥ V 4.
Planning the use 3.1 3 Overview Introduction This section describes the first steps after unpackaging, the permitted mounting positions and the fixation. This section describes the necessary considerations for EMC. Field of application The Panel PC is an industry-standard PC platform for demanding tasks in the field of PCbased automation.
Planning the use 3.3 Device identification data NOTICE The packaging protects the device during transport and storage. Therefore, never dispose of the original packaging material! 5. Please keep the enclosed documentation in a safe place. You will need the documentation when you start up the device for the first time. 6. Check the package contents for completeness and any visible transport damage. Check for completeness using the enclosed scope of delivery list. 7.
Planning the use 3.4 Mounting positions and fastening COA label Serial number: S VP ... Order No. 6AV78..... Microsoft Windows Product Key Ethernet address 1 Ethernet address 2 3.4 Mounting positions and fastening 3.4.1 Installation guidelines Before installing the device, read the following general notes relating to installation. WARNING Danger, high voltage Isolate the power supply to the switchgear cabinet before opening it.
Planning the use 3.4 Mounting positions and fastening ● The computer unit together with its AC power supply satisfies the requirements for fire protected enclosures according to EN 60950-1. Therefore it can be installed without any additional fire protective covering. ● The computer unit with DC power supply does not fulfill the requirements according to EN 60950-1 in the power supply unit area.
Planning the use 3.4 Mounting positions and fastening 3.4.2 Installation information stainless steel front Before you install the device, read the additional installation guidelines below: ● Make sure that you can access the device from the rear. ● The mounting cut-out should be deburred. ● When operating the device in a switch cabinet, ensure compliance with permitted ambient conditions and, in particular, that permitted ambient temperatures are not exceeded.
Planning the use 3.4 Mounting positions and fastening 3.4.4 Type of fixation The computer unit is secured in the mounting cut-out either with clamps or screws. NOTICE Securing with screws is not possible with the 12" touch screen variant. Select the type of fixation suitable to your requirements for the degree of protection (see section "Protection against dust and water") . 3.4.5 Stainless steel front type of fixation Type of fixation The device is fastened with the included clamps.
Planning the use 3.5 Mounting cutout IP54 degree of protection The IP54 degree of protection is applicable for the following conditions: Key panel Touch panel 12" 15" 15" 19" X X X - Screw mounting See also Industry Mall (http://mall.automation.siemens.com) 3.5 Mounting cutout 3.5.1 Preparing the mounting cut-out The following illustration shows the dimensions for the mounting cut-out.
Planning the use 3.5 Mounting cutout Table 3- 2 Dimensions for the mounting cut-out in mm Control unit L1 L2 L3 1) L4 1) L5 L6 2) L7 2) L8 2) L9 2) A1 A2 S1 S2 S3 S4 S5 3) S6 3) S7 3) Tolerance ±1 +1 ±0.2 ±0.2 ±0.5 ±0.5 ±0.5 ±0.
Planning the use 3.6 EMC Guideline Panel PC with operator control units Depth D Key panel with 12" TFT 105 mm Key panel with 15" TFT 124 mm Touch panel with 12" TFT 123 mm Touch panel with 15" TFT 121 mm Touch panel with 15" TFT INOX 126 mm Touch panel with 19" TFT 130 mm Note Additional mounting depth with optical drive The installation depth increases by 21 mm when an optical drive is installed in the device. 3.
Planning the use 3.
4 Mounting 4.1 Securing the device with clamps Requirement Accessories Display 12" 15" 19" Clamp 6x 6x 8x The clamps are provided with the control unit. Tool 2.5 mm hexagonal spanner Procedure Figure 4-1 Clamp assembly 1. Disconnect the device from the power supply. 2. Working from the front, insert the device into the 19" rack on the swivel arm or in the mounting cut-out. 3. Fasten the control unit from the rear using the clamps. 4. Tighten the setscrews to a torque of 0.4 - 0.5 Nm.
Mounting 4.2 Securing with screws 4.2 Securing with screws Note Securing with screws is not possible with the 12" touch panel variant. Drill holes in the control unit Steps for drilling holes 1 Drill holes (Ø approx. 2.5 mm) from the rear in the four recesses of the control unit. 2 Drill these holes with a diameter of Ø 5.5 mm for M5 and a Ø 6.5 mm for M6.
Mounting 4.3 Fix the device with stainless steel front using clamps IP54 degree of protection The IP54 degree of protection is guaranteed for mounting together with the ring seal. CAUTION Observe the panel seal when mounting Ensure you do not damage the panel seal when mounting the device. NOTICE Control cabinet installation: Material strength at the mounting cut-out Ensure that the material strength at the mounting cut-out is a minimum of 2 mm and a maximum of 6 mm.
Mounting 4.3 Fix the device with stainless steel front using clamps 4. Insert the fastening hooks (1) of the clamps into the recesses (2) of the device. Make sure that the centering points (4) of the clamps are inserted into the corresponding centering bore holes (3) of the clamping frame. Figure 4-3 Inserting the clamps 5. Tighten the screws of the clamps.
5 Connecting 5.1 Connection elements Ports Arrangement of the ports on the front of the device Item Description Description ① DVI/VGA DVI/VGA connection for CRT or LCD monitor with DVI port, VGA via DVI/VGA adapter ② Compact Flash card Slot for Compact Flash card ③ COM Serial V.24 port ④ USB 2.
Connecting 5.1 Connection elements Ports for connecting operator panels / displays Arrangement of the ports ① LVDS display ports for TFT displays up to 1024 x 768 pixels ② Access to 2nd LVDS display port for TFT displays up to 1280 x 1024 ③ USB 2.0 for front ④ Retaining screw for the steel cover plate that covers the ports described below.
Connecting 5.2 Connecting the 100 - 240 V AC Power Supply DC power supply Position of the DC power connector Description Plug connector for DC power supply of the device ① ② ③ + (24 V DC) - (ground) PE (ground terminal) 5.2 Connecting the 100 - 240 V AC Power Supply Note before connecting the device Note The varying voltage power supply module is designed for operation on 120/230/240 V AC networks. The setting of the voltage range takes place automatically.
Connecting 5.2 Connecting the 100 - 240 V AC Power Supply WARNING The permitted nominal voltage of the device must conform with local mains voltage. CAUTION The mains connector must be disconnected to fully isolate the device from mains. Ensure easy access to this area. A master mains disconnect switch must be installed if the device is mounted in a switch cabinet.
Connecting 5.2 Connecting the 100 - 240 V AC Power Supply Connecting How to connect the device to the 120 V AC / 230 V AC power supply 1 Ensure that the ON/OFF switch is in "0" position (Off) when you plug in the power cord in order to avoid unintentional startup of the device. 2 Connect the IEC connector 3 Connecting the power cord to the power socket 4 Fasten the cable with the supplied power plug latch ①, if necessary.
Connecting 5.3 Connecting the (24 V) DC power supply 5.3 Connecting the (24 V) DC power supply Note before connecting the device WARNING Only connect the device to 24 V DC power supply systems which meet the requirements of a safe extra-low voltage (SELV); in addition, a protective conductor must be connected. The conductors must withstand the short-circuit current of the 24 V DC power source, so that a short-circuit will not damage the cable. Only connect cables with a minimum crosssection of 1.
Connecting 5.4 Connecting the Equipotential Bonding Circuit Steps for connecting the device to the 24 V DC power supply 4 Fasten the cable with the supplied power plug latch, if necessary. Note Reverse-polarity protection The DC power supply (24V) has a mechanism to protect against reverse polarity. In the event the 24 V DC lines are reversed (24 V DC nominal (-15% / +20%) and connected to ground, the device will not sustain any damage. The device will simply fail to turn on.
Connecting 5.5 Equipotential bonding with stainless steel front Steps for connecting the equipotential bonding (1) 5.5 Connect the equipotential bonding connection (M4 thread) (1) on the device (large surface, large-area contact) with the central grounding point of the control cabinet. The minimum permissible cross-section is 5 mm2.
Connecting 5.7 Connecting the PROFINET strain relief 5.7 Connecting the PROFINET strain relief The PROFINET strain relief supplied in the product package is used to prevent accidental removal of the Ethernet cable and Industrial Ethernet FastConnect connector from the device. You need two cable ties to use the strain relief. To fix the PROFINET strain relief, you will need a TORX T10 screwdriver.
Connecting 5.
Integration into an automation system 6.1 6 Overview Introduction The following options are available for integrating the device in existing or planned system environments and networks. Ethernet Remote booting is supported. The integrated Ethernet interface can be used for communication and for data exchange with automation devices such as SIMATIC S7. You require suitable software for this: STEP 7, WinCC, WinCC flexible, WinAC, SIMATIC NET.
Integration into an automation system 6.2 Device in SIMATIC S7 network SIMATIC NET You can create, run and configure the SIMATIC installation with this software package. Information on this can be found on the SIMATIC NET Manual Collection CD. The software package and the documentation are not included in the package. Additional information You can find additional information in the catalog and in the Internet of Siemens A&D. http://www.siemens.com/automation/mall 6.2 Device in SIMATIC S7 network 6.2.
Integration into an automation system 6.3 Transferring authorizations Procedure 1. Disconnect the device from the mains. CAUTION Risk of damage to the device! Neutralize the static charge of your body, the device, and the connecting cables. You can do this by briefly touching the metal housing with the cable in your hand. 2. Insert the PROFIBUS cable in the MPI/DP socket. 3. Reconnect the device to the electrical power system. 6.3 Transferring authorizations Note The device has no floppy disk drive.
Integration into an automation system 6.5 PROFINET 6.5 PROFINET CP 1616 onboard The basic characteristics of the CP 1616 onboard are: ● Optimized for PROFINET IO ● With Ethernet-Real-Time-ASIC ERTEC 400 ● Three RJ45 sockets for connecting terminal devices or addition network components ● Integrated 3-port real-time switch ● Automatic hardware detection CAUTION Only one CP 1616 can be installed in a PC.
Integration into an automation system 6.5 PROFINET Document designation What is contained in this document? Manual SIMATIC NET - Twisted Pair and FiberOptic Networks Configure and build your Industrial Ethernet networks based on this document. This documentation is part of the supplied Documentation and Drivers CD: Operating Instructions CP 1616/CP 1604/CP 1616 onboard This provides you with all information required for operation. Installation guide Device Driver CP16xx.
Integration into an automation system 6.
Commissioning 7.
Commissioning 7.3 Windows XP, Windows 7 Security Center See also Additional applications (Page 53) 7.3 Windows XP, Windows 7 Security Center Warning from the Windows Security Center A warning from the Windows Security Center appears the first time you switch on your device. The Security Center checks the status of the device in regard to the three important security aspects listed below.
Commissioning 7.5 Additional applications Procedure 1. Accept the Microsoft licensing agreement. 2. Leave the regional settings of the operating system unchanged. If required, adjust the regional settings of the operating system only after commissioning. 3. Enter the company names and user names. 4. If this PC name is already in use as you attempt to connect the device to a network: Enter a new PC name for identification. The operating system will restart automatically. The system settings are updated.
Commissioning 7.5 Additional applications 7.5.1 Touch Panel set-up Note The configuration of the HMI device will be detected and set automatically. During the hardware recognition, the Touch Controller is detected again and entered. 1. Calibrate the touch screen by touching the selected points as shown in the illustration.
Commissioning 7.5 Additional applications 2. If "OSK on Windows Logon" is enabled, the Windows on-screen keyboard will be displayed every time you log on. You can use this keyboard to enter the password, for example. If you disable the "OSK on Windows Logon" option, then the Windows onscreen keyboard will not be displayed. An external keyboard will then be required to log on. In Windows 7 the Windows on-screen keyboard will not appear until you have assigned a password for the user account. 3.
Commissioning 7.6 BIOS settings 7.6 BIOS settings The BIOS setting "USB legacy Support" is enabled by default. Thus, the complete functionality of a USB keyboard is available prior to starting up Windows. You can also adjust the BIOS settings with the USB keyboard. Note To edit the BIOS on an operator device equipped with a touch screen, connect a USB keyboard. 7.7 USB Introduction Commercially available USB peripherals can be easily and flexibly connected via the USB interface.
Commissioning 7.8 Notes on operation 7.8 Notes on operation 7.8.1 DVD burner The DVD burner drive is an optional feature. Recording methods supported by the disk drive: Disc-at-once, Track-at-once, Session-at-once, Packet writing. You can write to CD-R, CDRW, DVD+R, DVD-R, DVD-RW, DVD+RW, DVD-RAM and dual-layer media. Burner software In order to utilize full functionality of the DVD burner under Windows XP, you need to install additional software (burning software).
Commissioning 7.8 Notes on operation Booting from the slave hard disk The system boots by default from the hard disk on SATA port 0. You can also configure the system to boot from the disk on SATA port 2. In order to allow booting from the second hard disk, you need to configure it as the primary boot device. Make the following settings in your BIOS Setup: Select Boot > Legacy > Hard Disk Drive > e.g. P0- ST3500418AS, then press the "+" key to move it up in the boot order.
Commissioning 7.8 Notes on operation RAID system management functions The pre-installed RAID system software offers enhanced functionality for RAID system operation and management. Start the software by selecting the "Start > Programs > Intel Rapid Storage Technology command. Figure 7-2 Example The "Manage > Advanced" command returns details of the RAID volumes. The command "Help > System Report > Save" can be used to create a report with details of the RAID volumes.
Commissioning 7.8 Notes on operation Comments about faults NOTICE Input delay System load may briefly increase due to synchronization when a hard disk has failed, depending on processor load and current hard disk activity. In extreme cases, input from the keyboard and touch screen may be delayed for a brief period. Before you replace the defective hard disk, create a backup copy of the system.
Commissioning 7.8 Notes on operation Flash drive functions A Flash drive or a Compact Flash card consists of Flash memory chips. An intelligent controller integrated in the Flash drive manages the Flash memory. This optimizes the use of the Flash memory to achieve a maximum service life. The service life of a Flash drive depends in part on the following factors: ● Type of file Executable files (*.EXE) are usually only written once and stays at the same storage location.
Commissioning 7.
8 Operation and configuration 8.1 Operator Controls On/Off switch On/Off switch Description Switch the device on using the on/off switch. This requires that the BIOS Setup entry "After Power Failure" is set to "Power On". WARNING The on/off switch does not isolate the device from the mains! When the switch is in 0 position (Off), the device is still supplied with mains voltage in order to generated the internal auxiliary voltage for the power supply.
Operation and configuration 8.2 Normal operation On/off button On/off button Description The on/off button has three functions: - Switch on the PC (press briefly 1x) - Shut down the operating system and PC (press briefly 1x) - Switch off the PC without shutting down the operating system (press and hold more than 4 seconds) = hardware reset. CAUTION Data may be lost when the PC performs a hardware reset.
Operation and configuration 8.2 Normal operation Procedure WARNING Danger of incorrect operations! The following applies to external input devices or combinations of external input devices and control units with key panels: Ambiguous key codes can cause serious malfunctions of the application program. Always activate the "Security features" of "KeyTools." Please note the applicable safety information in the "Operation and configuration" chapter in the section, "Additional drivers and applications.
Operation and configuration 8.3 Additional drivers and applications 8.2.3 Switching off the device Procedure 1. Shut down the operating system. CAUTION When using the operating systems Windows 2000 Professional, Windows XP Professional or Windows XP Embedded, wait until the display has turned dark. 2. Switch the device off using the On/Off switch. 3. In order to isolate the power supply completely, turn off the power at the power supply switch and pull out the plug from the device.
Operation and configuration 8.3 Additional drivers and applications 8.3.1 Standard calibration procedure Procedure 1. Select "Start > Programs > UPDD > Settings". The dialog box "UPDD Console" opens. Figure 8-1 Standard calibration 2. Select the Controller ① you wish to calibrate. 3. Click on the "Calibration" tab ②. 4. Activate the option box "Number of points" with the 25 points calibration ③. 5. Click the button "Calibrate" ④. The calibration screen is displayed in the selected display.
Operation and configuration 8.3 Additional drivers and applications 8.3.2 Procedure Activate touch functionality 1. Select "Start > Programs > UPDD > Settings". The "UPDD Console" dialog box opens. Figure 8-2 Activate touch functionality 2. Select the corresponding Controller ①. 3. Set a tick in the "Enabled" ③ option box in the "Properties" ② tab. The Controller is activated. 8.3.3 Procedure Extended Touch touch functionality 1. Select "Start > Programs > UPDD > Settings".
Operation and configuration 8.3 Additional drivers and applications The "Extended touch" option is preset. Note Extended touch applies only to the Windows 7 Ultimate operating system. If "Extended touch" is selected, the extended touch functions of Windows 7 will be available, such as operating touch permanently, which corresponds to the right mouse button function. 8.3.4 Deactivate touch functionality Procedure 1. Select "Start > Programs > UPDD > Settings". The dialog box "UPDD Console" opens.
Operation and configuration 8.3 Additional drivers and applications 8.3.5 KeyTools (for key panel devices) SIMATIC KeyTools is one selection of the applications for your Panel PC. These applications allow you to adapt key codes that are sent by the key panel of the control unit.
Operation and configuration 8.3 Additional drivers and applications 8.3.7 Panel PC Tools The program installs two software applications: Controlling backlighting Set the brightness ""Brightness" of the screen via the backlighting. The factory setting and the "default" value is 65. Call via an icon on the desktop. You can use the "<" and ">" buttons to change the value in each case in increments of one, the "<<" and ">>" buttons to change the value in increments of ten.
Operation and configuration 8.3 Additional drivers and applications 8.3.8 CheckLanguageID Scope The following description applies for 32-bit Windows operating systems. Call "c:\drivers\checklang\checklangid.exe" or reinstallation from the "Documentation and Drivers" CD. Function "CheckLanguageID" displays the currently installed languages.
Operation and configuration 8.3 Additional drivers and applications Setting up the language selection for Windows XP Professional The Multilanguage User Interface (MUI) allows you to set up the Windows XP Professional menus and dialogs for additional languages. The default setting on your device is Windows XP Professional MUI with English menus and dialog boxes and a US keyboard layout. You can change the language in the Control Panel.
Operation and configuration 8.
9 Operation 9.
Operation 9.2 Device with key panel 9.2 Device with key panel 9.2.1 Safety NOTICE Maloperation If you activate several keys simultaneously, a malfunction on the device cannot be excluded. Activate function keys and softkeys only in sequence! Malfunctions of the user software For security reasons, always use "Security features" of the KeyTools.
Operation 9.2 Device with key panel 9.2.3 Keys 9.2.3.
Operation 9.2 Device with key panel (1) Underline (2) Space character Figure 9-3 Alphanumeric keys 2 Toggling between lower-case and upper-case letters Enter the lower-case letters using the pre-defined assignment of the alphanumeric keys. To enter an upper-case letter, proceed as follows: 1. Hold down the key. 2. Activate the desired alphanumeric key at the same time. The displayed upper case letter will be entered. 3. To enter lower case letters, release the key. 4.
Operation 9.2 Device with key panel 9.2.3.3 Cursor keys Navigate, scroll or move the writing mark using the cursor keys. The cursor keys correspond to the usual keys of the PC keyboard. (1) key (2) key (3) key (4) key (5) Position 1 key (Home) (6) key (7) key Figure 9-4 9.2.4 Cursor keys External keyboards The keyboard layout has been set to "English/USA international.
Operation 9.2 Device with key panel CAUTION Labeling Label the function keys and softkeys to conform with the project. Labeling without reference to a project leads to incorrect operations on the system to be observed. Procedure 1. Label the DIN A4 film with a laser printer, for example, using the print format templates for MS Word on the "Documentation and Drivers" CD. 2. Cut the labeling strips along the pre-printed lines. Note Do not insert handwritten labeling strips until the ink has dried. 3.
Operation 9.3 Device with touch panel 9.2.6 Using the integrated mouse The position on which you press the middle round button of the integrated mouse determines the direction in which the cursor moves. The amount of pressure determines the speed of the cursor. Alternatively to using the integrated mouse you can also connect an external mouse to the front USB port. Figure 9-6 9.3 Integrated mouse Device with touch panel The individual variants differ in their dimensions and size of the display.
Operation 9.3 Device with touch panel 9.3.1 Operating a touch panel On the display that is touch-sensitive due to the touch sensor, application-specific user interface elements, for example buttons, are displayed. When you tap the command button with your finger, the function assigned to the button is activated. The following types of pressure are permissible: ● Using a plastic pen with a 1 mm radius at the point: 25 g. ● Using a silicone finger with a diameter of 1.6 cm: 50 g.
Operation 9.3 Device with touch panel Dimensions Length 155 mm Maximum diameter 20 mm CAUTION Damage to the keys The touch pen is not appropriate for operating the keys.
Operation 9.
10 Functions 10.1 Introduction Even in its basic version, the device supports the use of monitoring functions. When used in combination with the appropriate software, the following functions for displaying, monitoring and controlling are available: ● Temperature monitoring (over / under temperature) ● Monitoring of the battery level ● Monitoring of hard disks, CompactFlash cards and SSD drives with S.M.A.R.T.
Functions 10.3 Watchdog (WD) Temperature errors do not occur under normal operation.
Functions 10.4 Fan monitoring 10.4 Fan monitoring The function monitors operation of the enclosure and power supply fans. When a fan fails, the following reactions are triggered: Response Option The DiagBase or DiagMonitor software is enabled None The fan fault is retained in memory until the cause of the fan failure has been rectified and the error is reset by taking one of the following measures: ● Acknowledgment of the error message by the monitoring software ● Restart of the device 10.
Functions 10.
11 Service and maintenance 11.1 Maintenance Scope of maintenance The device is largely maintenance-free. If the functioning of components, such as the backup battery, has been impaired after a limited period of operation, they must be replaced. Please see the relevant chapters of these operating instructions for detailed information.
Service and maintenance 11.2 Maintenance and care of devices with stainless steel front Procedure for cleaning the device (front) 1. Switch off the device. This prevents the accidental triggering of functions when the front is touched. 2. Dampen the cleaning cloth. 3. Spray the cleaning agent on the cloth and not directly on the device. 4. Clean the device with the cleaning cloth. Resistance to chemicals CAUTION Adhere to the information regarding chemical resistance of the panel front.
Service and maintenance 11.2 Maintenance and care of devices with stainless steel front Cleaning the front membrane Clean the front membrane using the equipment described below: ● Soft, non-abrasive window wipers or a soft, clean rag ● Rubber window wipers ● Liquid glass cleaners ● Kitchen or household paper Additional information is available in the section "Chemical resistance of stainless steel fronts (Page 92)".
Service and maintenance 11.3 Chemical resistance of stainless steel fronts 11.3 Chemical resistance of stainless steel fronts Front membrane The resistance of the front membrane to various chemicals was tested to DIN 42 115, section 2. The front membrane is resistant to the chemicals listed below: ● Alcohol ● Diluted acids ● Diluted caustic solutions ● Ester ● Hydrocarbons ● Household cleaners 11.
Service and maintenance 11.5 Spare parts ● Make sure surface is not damaged: Do not damage the device during operation, or by cleaning or repairing it using hard objects, in particular objects made of non-stainless steel material. ● Avoid contact of the surface with corrosive parts: Extraneous rust from water lines, file chips, residue of wire brushes or steel wool and rust films have a corrosive effect on parts made of stainless steel. – Remove any stains or extraneous rust immediately.
Service and maintenance 11.6 Separating the control unit from the computer unit 11.6 Separating the control unit from the computer unit The control unit is separated from the computer unit to carry out repairs or to replace the control unit, for example. Procedure 1. Disconnect the device from the mains. 2. Open the switchgear cabinet. The device is now accessible from the back. 3.
Service and maintenance 11.6 Separating the control unit from the computer unit Figure 11-2 Other ports on the computer unit Similar to illustration, can deviate from device (1) Display cable (for touch panels > 15", 2 pieces) (2) USB cable (3) IO USB cable Separating the device in an uninstalled state As an alternative, dismount the device completely and separate the control unit and computer unit from one another in an uninstalled state.
Service and maintenance 11.7 Expansion and parameter assignment 11.7 Expansion and parameter assignment 11.7.1 Opening the Device CAUTION Work on the open device may only be carried out by authorized and qualified personnel. Within the warranty time, you are only allowed to install expansions for memory and expansion card modules. CAUTION The device contains electronic components which may be destroyed by electrostatic charge. You therefore need to take precautionary measures before you open the device.
Service and maintenance 11.7 Expansion and parameter assignment Open the device up Steps for opening the device 1 Remove the screws ①. 2 Swing the cover up and remove it. 11.7.2 Memory expansion 11.7.2.1 Removing/Installing Memory Module Memory expansion options The motherboard is equipped with 2 slots for memory modules. For 184-pin DDR3 RAM chips, unbuffered, without/with ECC. This allows you to expand device memory up to 4 GB, of which you can use approx. 3.
Service and maintenance 11.7 Expansion and parameter assignment Preparation Disconnect the device from mains and unplug all cables. CAUTION The electronic components on the PCBs are highly sensitive to electrostatic discharge. Always take appropriate precautionary measures when handling these components. Refer to the ESD directives on handling electrostatic sensitive components. NOTICE We highly recommend using memory modules approved by Siemens.
Service and maintenance 11.7 Expansion and parameter assignment Display of the current memory configuration A new memory module is automatically detected. When switching on the device and starting the BIOS Setup using , the current memory size is displayed under "Total Memory". 11.7.3 Installing PCI/PCIe cards 11.7.3.1 Notes on the modules The device is designed for use with modules conforming to PCI specifications V 2.2. 5 V 32bit PCI modules, universal (5 V & 3.
Service and maintenance 11.7 Expansion and parameter assignment Inserting the slider Proceed as follows when using the slider: How to install a slider 1 Push the slider through the guide slot until it is seated firmly on the module. Insert the module into the slot. CAUTION Do not put pressure on the module! Do not apply excessive force on the slider when you push it onto the module.
Service and maintenance 11.7 Expansion and parameter assignment 11.7.4 Installing drives 11.7.4.1 Options of installing disk drives Drive bay module for hard disk drives and optical drives DVD burner drive bay mount Item Description ② DVD burner drive bay mount Item Description ① Slot for one 3.5" drive ② Hard disk drive bay for one 3.5" drive Two 2.5" hard disks Item Description Operating Instructions, 05/2010, A5E02722710-01 Slot for DVD burner drive A 3.
Service and maintenance 11.7 Expansion and parameter assignment 11.7.4.2 Installing/removing a drive bay module Preparations Isolate the device from mains and disconnect all connection cables. Removing a drive bay module for hard disks and optical drives Steps for removing the drive bay 1 Remove the four screws ①. 2 102 Lift out the drive bay module for hard disks and the optical drive.
Service and maintenance 11.7 Expansion and parameter assignment 11.7.4.3 Removing / installing an optical drive Preparations Isolate the device from mains and disconnect all connection cables. Required tools You need the following screwdrivers to remove the the DVD burner: ● Torx T10 to mount/remove the drive bay ● Torx T6 to install/remove the drive Removing the DVD burner drive How to remove a DVD burner drive 1 Remove the drive bay module. 2 Loosen the screws ① on the DVD burner drive bay.
Service and maintenance 11.7 Expansion and parameter assignment 11.7.4.4 Installing / removing hard disks Removing 2.5" drives How to remove a 2.5" drive 1 Remove the drive bay module. 2 Unscrew ① the drive. 3 Remove the hard disk drive and the steel mounting bracket from the bay. 4 Disconnect the power supply and the data cable from the drive. Removing a 3.5" drive How to remove a 3.5" drive 1 Remove the drive bay module. 2 Disconnect the power supply and the data cable from the drive.
Service and maintenance 11.7 Expansion and parameter assignment 11.7.4.5 Removing/installing an SSD drive Preparation Disconnect the device from the mains. Note The use of the SSD drive excludes the simultaneous use of a hard disk. Installing an SSD drive How to install the SSD drive 1 Remove the hard disk cover and place it on the device. 2 Connect the power supply cable and the data cable to the SSD drive. Fasten the SSD drive with four (4) screws ①. 4 Mount the hard disk cover.
Service and maintenance 11.7 Expansion and parameter assignment 11.7.5 Installing/removing an on-board Compact Flash card NOTICE We highly recommend that use use approved SIMATIC Compact Flash cards. Siemens disclaims any liability for impairment of functions caused by the use of third-party cards. Memory expansion options The device features a slot for Compact Flash cards types I / II. NOTICE This slot is not hot-plug capable.
Service and maintenance 11.7 Expansion and parameter assignment How to install a Compact Flash card 2 Slide the cover plate of the module slot towards the DVI connection and lift it out. Installing the Compact Flash card How to install a Compact Flash card 1 Open the board slot. 2 Insert the Compact Flash card in the slot with the connector facing in until it locks into place. 3 Open the module slot. Note The Compact Flash slot is coded against reversed insertion.
Service and maintenance 11.7 Expansion and parameter assignment Removing the Compact Flash card How to remove a Compact Flash card 11.7.6 1 Open the board slot. 2 Press the eject button, for example with the cover of the module slot, and remove the Compact Flash card. 3 Open the module slot. Installing/removing an additional Compact Flash card NOTICE We highly recommend that use use approved SIMATIC Compact Flash cards.
Service and maintenance 11.7 Expansion and parameter assignment Installing the additional Compact Flash card How to install the Compact Flash card in the Compact Flash adapter 1 Remove the hard disk cover. 2 Lift out the Compact Flash adapter module and lay it on the device. 3 Remove the screws ① and remove the CompactFlash latch.
Service and maintenance 11.8 Removing and installing hardware components How to install the Compact Flash card in the Compact Flash adapter 4 Insert the Compact Flash card in the adapter with the connector facing in until it locks into place. 5 Close the Compact Flash latch. 6 Mount the hard disk cover. 11.8 Removing and installing hardware components 11.8.1 Repairs Repairing components Only authorized personnel are permitted to repair the device.
Service and maintenance 11.8 Removing and installing hardware components Disclaimer of liability All technical data and approvals apply only to expansion units which are released by SIEMENS. Siemens disclaims any liability for impairment of functions caused by the use of third-party devices or components. Tools You can perform all installation tasks on the device using Torx T6, T10, T15 and T20 screwdrivers. 11.8.
Service and maintenance 11.8 Removing and installing hardware components Disposal CAUTION Batteries must be disposed of in accordance with local regulations. Preparation Note For the BIOS setting "Profile: Standard" the configuration data of the device is deleted when the battery replacement takes more than 30 seconds. For the BIOS setting "Profile: User" the configuration data of the device is retained; only the date and time has to be reconfigured.
Service and maintenance 11.8 Removing and installing hardware components Steps for replacing the battery 2 Remove the battery holder. 3 Detach the cable. 4 Remove the old battery. 5 Fasten the new battery and reinsert the battery holder. 6 Close the battery compartment. Reconfiguring the BIOS setup If the battery replacement took longer than 30 seconds, the configuration data of the device have been deleted and you need to reconfigure these in the BIOS Setup.
Service and maintenance 11.8 Removing and installing hardware components 11.8.4 Removing/Installing the Power Supply WARNING Only authorized trained personnel are allowed to replace the power supply unit. Preparations 1. Isolate the device from mains and disconnect all connection cables. 2. Open the device (Page 96). Removing the power supply unit How to remove the power supply module 1 Remove the drive bay module for the hard disk and DVD burner.
Service and maintenance 11.8 Removing and installing hardware components 11.8.5 Preparation Installing / removing the bus board 1. Isolate the device from mains and disconnect all connection cables. 2. Open the device (Page 96). Removing the bus board How to remove the bus board 1 Remove all modules from the slots. 2 Lift out the drive bay module for hard disks and the DVD burner. 3 Loosen the screws ① and remove the power supply cover. 4 Remove the power supply.
Service and maintenance 11.8 Removing and installing hardware components 11.8.6 Installing / removing the motherboard Preparation 1. Isolate the device from mains and disconnect all connection cables. 2. Open the device (Page 96). Removing the motherboard How to remove the motherboard 1 Remove the drive bay module for the hard disk and DVD burner. 2 Remove the screw ②. Remove the module bracket ①. 116 3 Remove the power supply cover. 5 Remove the power supply. 4 Remove the bus board.
Service and maintenance 11.8 Removing and installing hardware components How to remove the motherboard 8 Remove the hexagon bolts (6 pieces) from the ports. 9 Remove the motherboard.
Service and maintenance 11.8 Removing and installing hardware components 11.8.7 Installing / removing the equipment fan Preparations 1. Disconnect the device from the mains. 2. Open the device (Page 96). Removing the fan How to remove the fan 1 Pull the fan plug ① from the motherboard. 2 Loosen the four plastic rivets ① on the enclosure. 3 118 Take the fan out of the enclosure.
Service and maintenance 11.8 Removing and installing hardware components Installing the fan NOTICE Always install a fan of the same type! Fan mounting position The figure shows the correct fan mounting position. Pay attention to the direction of the arrow on the fan enclosure! 11.8.8 Installing / removing the power supply fan Preparations 1. Disconnect the device from the mains. 2. Open the device (Page 96). 3. Remove the power supply.
Service and maintenance 11.8 Removing and installing hardware components How to remove the fan 2 Loosen the four screws ① on the enclosure. 3 Take the fan out of the enclosure. Installing the fan NOTICE Always install a fan of the same type! Fan mounting position The diagram shows the correct mounting position of the fan. Pay attention to the direction of the arrow on the fan enclosure! 11.8.9 Processor replacement Operation of the CPU is not possible.
Service and maintenance 11.9 Installing the software 11.9 Installing the software 11.9.1 Reinstalling the operating system 11.9.1.1 Windows Embedded Standard 2009 General installation procedure If your software becomes corrupt for any reason, you can reinstall it from the Restore CD. The Restore CD contains a image file for the hard disk or Compact Flash card with the original software (operating system with installed hardware drivers) and is included in the Windows Embedded package variant.
Service and maintenance 11.9 Installing the software CAUTION All existing data, programs, user settings and authorizations or license keys on the drives will be deleted and are therefore lost. For information on the functions, refer to the README.TXT file on the Restore CD. Note The "USB Boot" option has to be set to "Enabled" in the Boot menu of the BIOS so that the device can address a USB CD-ROM drive. 11.9.1.
Service and maintenance 11.9 Installing the software Restoring factory state To restore the factory state, proceed as follows: 1. If the device does not have an optical drive, connect a USB DVD-ROM drive to the device. 2. Insert the Restore DVD in the drive and reboot the device. When the BIOS message Press go to Setup Utility Press go to Bootmanager appears, press the F2 key. 3. Select the Boot menu and move the entry "CD/DVD-ROM Drive" or ODD to the first position. 4.
Service and maintenance 11.9 Installing the software Setting up and formatting partitions Set up the hard disk partitions after having installed a new hard disk, or to repair faulty partitions, or to change the partitioning. In the next dialog box, you can set up the hard disk according to your requirements and add controllers that are not yet known to the system. 124 Options Meaning Drive options (advanced) Further functions are displayed with which you can set up the hard disk.
Service and maintenance 11.9 Installing the software Options Meaning Refresh Updating Delete Deleting a partition Format Formatting a partition New Creating new partitions Load Driver To add new drivers, for example the driver for RAID Extend Changing the partition size Any error messages that occur are displayed behind this icon, for example if the hard disk was not formatted in the required "NTFS" format. The first partition should be at least 25 GB.
Service and maintenance 11.9 Installing the software Now follow the instructions on the screen. Note If you want to reinstall drivers from a USB floppy disk drive, select Floppy Drive (A:) . Note If you want to use Microsoft Windows as a professional user, you will need the following manual (not supplied): Windows 7 Technical Reference (MS Press No.
Service and maintenance 11.9 Installing the software 11.9.2.2 Setting up partitions under Windows XP Professional / Windows 7 Ultimate Set up the hard disk partitions after having installed a new hard disk, or to repair faulty partitions, or to change the partitioning. Partitioning the hard disk The factory state of the hard disk with Windows XP/Windows 7 Ultimate includes the following partitions: Partition Name Size File system 1. Partition SYSTEM 25 GB NTFS (not compressed) 2.
Service and maintenance 11.9 Installing the software 11.9.3.2 Driver installation under Windows Embedded Standard 2009 The driver installation under Windows XP Embedded is conducted in the same way as under XP Professional. Pay attention to the installation instructions of the driver manufacturer. When drivers are being installed under Windows XP Embedded, you may see a message that the Windows XP Installation CD or SP2 CD is required. In this case, insert the Restore DVD.
Service and maintenance 11.9 Installing the software 11.9.4.2 Replacing a defective drive in the RAID system A missing drive is reported via the RAID software. Figure 11-3 Degraded message of RAID software Replace defective RAID drives with a new drive in order to recover secure RAID1 state. The RAID software reports the defective drive and returns details of the operable hard drive.
Service and maintenance 11.9 Installing the software Always replace the defective drive with a new one of the same type and capacity. To be able to boot from the RAID system, you must place this first in the list of bootable sources in the BIOS "Boot" setup menu. Otherwise the system will boot from the hard disk you have just installed and the message "Operating system not found" will be displayed.
Service and maintenance 11.9 Installing the software 11.9.4.3 Installing the RAID Controller software You find the procedure for installing the RAID controller software in the RAID user manual on the supplied "Documentation and Drivers" CD. Note concerning Windows XP Professional You need to select the Intel BD82QM57 Controller from the provided list when installing Windows XP Professional for the first time. 11.9.5 Installing burner software 11.9.5.
Service and maintenance 11.9 Installing the software 11.9.6.2 Installing or updating application programs and drivers In order to install software from a CD and/or floppy disc under Windows XP Embedded / Windows XP Professional, the corresponding drive must be installed or connected. Drivers for USB floppy disk and CD-ROM drives are included in Windows XP Embedded/Windows XP Professional and do not have to be installed from other sources.
Alarm, error, and system messages 12.1 12 Boot error messages BIOS first performs a Power On Self Test (POST) within the boot routine to verify proper operation of certain functional units of the PC. The boot sequence is interrupted immediately if fatal errors occur. If the POST does not return an error, the BIOS initializes and tests further functional units. In this startup phase, the graphics controller is initialized and any error messages are output to the screen.
Alarm, error, and system messages 12.2 Introduction to the BIOS beep codes 12.2 Introduction to the BIOS beep codes The device performs a self-test when it is switched on. If an error is detected during the POST (Power On Self-Test), a series of beep signals are issued. The beep tones are a code for errors and are composed of 2 x 2 sequences.
Alarm, error, and system messages 12.3 BIOS beep codes 12.3 BIOS beep codes The following section lists the POST codes relevant to users in the sequence in which they occur: Contact Customer Support (http://www.siemens.com/automation/service&support) for information on all other POST codes.
Alarm, error, and system messages 12.
Alarm, error, and system messages 12.
Alarm, error, and system messages 12.3 BIOS beep codes Display (hex) Meaning Description 34H BDS_ENTER_LEGACY_16_BOOT Ready to Boot Legacy OS.
Alarm, error, and system messages 12.
Alarm, error, and system messages 12.
Alarm, error, and system messages 12.
Alarm, error, and system messages 12.
13 Troubleshooting/FAQs 13.1 General problems This chapter provides you with tips on how to localize and troubleshoot frequently occurring problems. Problem Possible causes Remedy The device is not operational There is no power supply to the device. Windows no longer boots Device is being operated outside the specified ambient. conditions Check the ambient conditions. After transport in cold weather, wait approximately 12 hours before switching on the device.
Troubleshooting/FAQs 13.1 General problems Problem Possible causes Remedy Although the BIOS setting is OK, the time and data are still wrong. The backup battery is dead. Replace the backup battery. USB device not responding. The USB ports are disabled in your Use a different USB port or enable the port. BIOS. Operating system does not support Enable USB Legacy Support for the mouse and the USB port. keyboard. For other devices you need the USB drivers for the respective operating system.
Troubleshooting/FAQs 13.2 Problems when Using Modules of Third-party Manufacturers 13.2 Problems when Using Modules of Third-party Manufacturers Problem Possible cause The PC crashes during startup Double allocation of I/O addresses Double allocation of hardware interrupts and/or DMA channels Signal frequencies or signal levels are incorrect.
Troubleshooting/FAQs 13.
14 Technical data 14.1 General specifications Electrical specifications Supply voltage AC Nominal 100 - 240 V AC (-15% / +10%), autorange Supply voltage DC Nominal 24 V DC (-20% / + +20%), SELV AC device: Frequency 50 to 60 Hz, 47 to 63 Hz Input current AC Continuous current to 2.3 A (to 50 A for 1 ms at startup) Input current DC Continuous current to 8 A (to 14 A for 30 ms at startup) Line voltage frequency 50 to 60 Hz (47 to 63 Hz) Transient voltage interruption Namur Max.
Technical data 14.1 General specifications Disk drives Hard disks 2.5'' or 3.5'' Serial ATA, hard disk capacity see order documentation 3 Gbps data transfer rate Supports NCQ (Native Command Queuing) SATA II property DVD burner Serial ATA, See order documentation for features Oscillations, max.: 10 to 58 Hz: 0.019 mm / 58 to 500 Hz: 2.
Technical data 14.
Technical data 14.1 General specifications Safety 12" TFT Key panel Degree of protection 15" TFT Key panel 12" TFT Touch panel 15" TFT 19" TFT 15" INOX Touch panel Touch panel Touch panel IP65/Enclosure Type 4 with clamp mount, encircling seal and pressedon plastic cap for USB port*) IP54 with screw fastening Protection class Protection class I according to IEC 61140 Safety regulations AC: EN 60950-1; UL60950-1; CAN/CSA C22.2 No 60950-1-03 DC: EN 61131-2; UL508; CSA C22.
Technical data 14.1 General specifications Climatic conditions Temperature During operation1) 2) Installed in cabinet: – With outside temperature of 40° C 1) – With outside temperature of 45° C Storage, transportation Gradient Tested to IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-14 +5° to +45° C (with maximum configuration) Inside temperature max. 50° C (with total load of the slots with max. 15 W) Inside temperature max.
Technical data 14.2 Ports and status displays 14.2 Ports and status displays Ports DVI-I Port for external CRT / LCD monitor USB External: 4x USB 2.0 on the port side (max. 2 can be simultaneously operated as high current) There are 3 USBs available internally: 1x USB 2.0 high current + 1x USB 2.0 low current on a 10-pole male connector, 1x USB 2.0 low current for internal USB stick/dongle Front ports: 1x USB 2.0 high current 1x USB 1.
Technical data 14.3 Current/power requirements of the device 14.3 Current/power requirements of the device Maximum current values Component Base device Voltage 1) 2) Hard disk drive 1 x 3.5" 2) +5 V +3.3 V 8.5 A 2.3 A 0.6 A Hard disk drives 2 x 2.5" 2) 1.2 A DVD burner drive 2) 0.8 A USB ports 3) PCI/PCIexpress slots +12 V -12 V 0.7 A 0A 0.5 A 1.2 A 4A 6A 2A Internal front interfaces (on panel devices) 2.5 A 0.1 A 3.5 A Individual currents (max. permissible) 4) 16.5 A 8.5 A 6.
Technical data 14.4 AC voltage supply 14.4 AC voltage supply Technical specifications Degree of protection IP20 (in installed state) Protection class VDE 0106 Note The power supply contains an active PFC (Power Factor Correction) circuit to conform to the EMC guidelines. Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the normal and buffered mode when used with SIMATIC PCs with an active PFC.
Technical data 14.5 DC power supply 14.5 DC power supply Specifications Degree of protection IP20 (in installed state) Protection class VDE 0106 1) 15 W per PCI slot included Power supply characteristics DC power supply Input data Voltage Nominal 24 V DC (-15% / +20%), SELV Continuous current Max. 8 A Starting current (load-independent) to 14 A for 30 ms Active power 190 W Output data Voltages +5 V / 16.5 A * (18.5 A peak) +3.3 V / 8.5 A * * total of 90 W permitted +12 V / 6.
Technical data 14.6 Keyboard table 14.6 Key codes Keyboard table The following table applies only to control units with key panels. It contains all characters that can be entered in SIMATIC KeyTools in the "Key code table" area and under "User specific". The character that is triggered by pressing a specific key is listed in the "Display/function" column. Further information is available in the documentation for SIMATIC KeyTools on the "Documentation and Drivers" CD.
Technical data 14.
Technical data 14.
Technical data 14.
Technical data 14.6 Keyboard table Name Code (Hex) 0x ’" 34 ‘~ 35 ,< 36 .> /? 38 Display/function — L Shift/R Shift " R Alt ´ R Alt+L Shift/R Shift ¨ — ‘ L Shift/R Shift ~ — , L Shift/R Shift < R Alt ç R Alt+L Shift/R Shift Ç — .
Technical data 14.
Technical data 14.6 Keyboard table 162 Name Code (Hex) 0x Check-box Display/function Keypad . Delete 63 — Keypad .
15 Dimensional drawings Dimension drawing IPC , - PP . 15.
Dimensional drawings 15.1 Dimension drawing IPC / 1 0 Figure 15-2 Dimension drawing IPC, computer unit swung away from control unit Table 15- 1 Dimensions of IPC677C in mm Control unit 164 Key panel Touch panel 12" TFT 15" TFT 12" TFT 15" TFT 15" TFT INOX 19" TFT A 482.6 482.6 400.0 482.6 482.6 482.6 B 310.3 354.8 310.3 310.3 310.3 400.0 C 447.2 447.2 366.0 450.0 450.0 450.0 D 314.9 314.9 314.9 314.9 314.9 314.9 E 30.8 49.8 37.8 46.6 46 56.1 F 39.8 59.
Dimensional drawings 15.2 Dimensional drawings for the installation of expansion modules 15.
Dimensional drawings 15.
16 Detailed descriptions 16.1 Motherboard 16.1.1 Structure and functions of the motherboard The essential components of the motherboard are the processor and the chip set, two slots for memory modules, internal and external interfaces and the Flash BIOS.
Detailed descriptions 16.1 Motherboard 16.1.2 Technical features of the motherboard Component / interface Description Characteristics Chip set Single chip set Mobile Intel® QM57 Express Chipset BIOS Update by means of software InsideH20 Setup Utility Rev. 3.x CPU Intel® Celeron P4505 1.86 GHz Intel® Core i3-330E 2.13 GHz Intel® Core i7-610E 2.
Detailed descriptions 16.1 Motherboard 16.1.3 Position of the interfaces on the motherboard Ports The motherboard of the device features the following interfaces: ● Interfaces for the connection of external devices ● Interfaces for internal components (drives, bus boards etc.
Detailed descriptions 16.1 Motherboard 16.1.4 External ports ; Figure 16-2 ; ; ; ; ; ; ; Connector pin assignment on the port * Optional product variant Interface Positio n Connecto Description r USB 2.
Detailed descriptions 16.1 Motherboard The connectors are of type A. All ports are designed as high current USB (500 mA), you can only use a maximum of 2 simultaneously as high current, however. CAUTION No USB devices can be connected which feed back voltage to the Box PC. PROFIBUS/MPI interface X4 PROFIBUS/MPI interface 1 Pinno.
Detailed descriptions 16.1 Motherboard PROFINET LAN X3 Port P1, P2, P3 PROFINET interface 1 /(' /(' Pinno.
Detailed descriptions 16.1 Motherboard Ethernet RJ45 connection LED 1 Off: 10 Mbps Lit in green color: 100 Mbps Lit in orange color: 1000 Mbps – LED 2 Lit: Active connection (to a hub, for example) Flashing: Activity – Note The interfaces available on the device have been numbered so they can be clearly distinguished. This numbering may deviate from the numbering provided by the respective operating system. DVI-I port, X70 DVI-I port Pinno.
Detailed descriptions 16.1 Motherboard DVI-I port 14 +5 V +5 V Output 15 GND Ground – 16 MONDET Hotplug detect Input 17 TX0N TDMS data 0- Output 18 TX0P TDMS data 0+ Output 19 GND Ground – 20 NC Unassigned – 21 NC Unassigned – 22 GND Ground – 23 TXCP TDMS clock + Output 24 TXCN TDMS clock - Output Compact Flash card, X50 Compact Flash card port Pin no.
Detailed descriptions 16.1 Motherboard Serial interface COM 1, X30 The COM1 serial port has the following pin assignment: Serial interface COM1 16.1.5 Pinno.
Detailed descriptions 16.1 Motherboard Pin assignment of the equipment fan, X132 Pin no. Short description Meaning Input / Output 1 GND Ground - 2 +12 V Switched voltage supply Output 3 CPU FAN_CLK Clock signal Input Pin assignment of the supply for the power supply fan, X131 Pin no.
Detailed descriptions 16.1 Motherboard Pin assignment of the internal USB interface connector, X43 16.1.6 Pin no.
Detailed descriptions 16.1 Motherboard Display interface (1st LVDS channel), X400 Pin no. Short description Meaning Input / Output 1 P5V_D_fused +5V (fused) display VCC Output 2 P5V_D_fused +5V (fused) display VCC Output 3 RXIN0- LVDS output signal bit 0 (-) Output 4 RXIN0+ LVDS output signal bit 0 (+) Output 5 P3V3_D_fused +3.3V (fused) display VCC Output 6 P3V3_D_fused +3.
Detailed descriptions 16.1 Motherboard Pin no. Short description Meaning Input / Output 17 GND Ground - 18 P12VF +12 V fused Output 19 P12VF +12 V fused Output 20 P12VF +12 V fused Output Assignment of the display to the display select pins One of the 15 available displays is configured automatically via the display select inputs. The display select inputs are connected to pull–up resistors, i.e. if these inputs are not interconnected, they are high level.
Detailed descriptions 16.1 Motherboard I/O front port for operator panels, X44 This port carries all signals required for connecting operator panels in addition to the display interface. The maximum cable length is 50 cm at a USB data rate of 12 Mbps. Pin no. Short description Meaning Input / Output 1 GND Ground - 2 P12V Inverter voltage supply Output 3 BL_ON Backlight on (5 V = On) Output 4 P5V_fused +5 V (fused) Output 5 GND Ground - 6 P3V3_fused +3.
Detailed descriptions 16.2 Bus board Pin Assignment of the USB 2.0 interface, X42 Pin no. Short description Meaning Input / Output 1 VCC + 5 V, fused Output 2 USB5 USB5_M Input / Output 3 USB5 USB5_P Input / Output 4 GND Ground - S1 S Shield - S2 S1 Shield - Note For detailed information on the pin assignments of the interfaces, please contact Customer Support (http://www.siemens.com/automation/service&support) or the Repair Center. 16.2 Bus board 16.2.
Detailed descriptions 16.2 Bus board Variant 2 has one PCI and one PCI Express slot. 16.2.
Detailed descriptions 16.2 Bus board 5V System Environment Side B Side A 23 AD[27] AD[26] 24 AD[25] Ground 25 +3.3V AD[24] 26 C/BE[3]# IDSEL 27 AD[23] +3.3V 28 Ground AD[22] 29 AD[21] AD[20] 30 AD[19] Ground 31 +3.3V AD[18] 32 AD[17] AD[16] 33 C/BE[2]# +3.3V 34 Ground FRAME# 35 IRDY# Ground 36 +3.3V TRDY# 37 DEVSEL# Ground 38 Ground STOP# 39 LOCK# +3.3V 40 PERR# SDONE 41 +3.3V SBO# 42 SERR# Ground 43 +3.
Detailed descriptions 16.2 Bus board 16.2.3 16.2.4 Pin assignment 12 V power supply connection for WinAC module Pin Short description Meaning Input /Output 1 +12 V 1 12 V voltage Output 2 GND Ground - 3 GND Ground - 4 +5 V 5 V voltage Output 1 1) max. permissible current: 1 A; with this power demand the total power demand for the PCI slots are not allowed to be exceeded.
Detailed descriptions 16.3 System resources 16.3 System resources 16.3.1 Currently allocated system resources All system resources (hardware addresses, memory configuration, allocation of interrupts, DMA channels) are assigned dynamically by the Windows OS, depending on the hardware configuration, drivers and connected external devices. You can view the current configuration of system resources or possible conflicts with the following operating systems: 16.3.
Detailed descriptions 16.
Detailed descriptions 16.3 System resources 16.3.2.2 Interrupt Assignments The functions are assigned different interrupts, depending on the operating system. A distinction is made between the PIC and APIC modes.
Detailed descriptions 16.
Detailed descriptions 16.3 System resources Exclusive interrupt in PIC mode The interrupts are automatically assigned to the slots at system startup due to the default settings in system BIOS. Several slots may share the same interrupt, depending on the system configuration. This functionality is known as interrupt sharing. Exclusive interrupts are not available in PIC mode. Disable specific system resources in order to obtain exclusive interrupts.
Detailed descriptions 16.4 BIOS Setup 16.4 BIOS Setup 16.4.1 Overview BIOS Setup program BIOS SETUP allows you to set the hardware configuration, and system properties. SETUP is also used to set the time and date of the realtime clock. Changing the device configuration Your device configuration is preset for operating with the included software. You should only change the default values if you have modified the technical configuration your device, or if a fault occurs when the unit is powered up. 16.
Detailed descriptions 16.4 BIOS Setup 16.4.3 BIOS Setup menus The various menus and submenus are listed on the next pages. You can obtain information on the selected SETUP item from the "item-specific help" part of the respective menu. Figure 16-5 SETUP Main menu (example) Menu layout ① Header ④ Help window ② Menu bar ⑤ Command line ③ System information The screen is divided into four sections.
Detailed descriptions 16.4 BIOS Setup 16.4.4 Main menu Figure 16-6 Main menu (example) Settings in the main menu In the main menu, you can move up and down to select the following system configuration boxes by means of the [↑] up and [↓] down cursor keys: Field Meaning System Time For viewing and setting the current time System Date For viewing and setting the current date System time and date System Time and System Date indicate the current values.
Detailed descriptions 16.4 BIOS Setup 16.4.5 Advanced menu Menu layout Figure 16-7 "Advanced" menu (example) Settings in the Advanced Menu Entry Meaning Peripheral Configuration Configuration of components on the motherboard. SATA Configuration Configuration of the SATA interface. Video Configuration Configuration of the graphics interface USB Configuration Configuration of the USB ports Chipset Configuration Extended chipset configuration.
Detailed descriptions 16.4 BIOS Setup Advanced menu > "Peripheral Configuration" Figure 16-8 "Peripheral Configuration" submenu Entry Meaning Internal COM 1 Enable (Enabled) or disable (Disabled) the serial port or configure it automatically (Auto) With Enabled, it is possible to specify the I/O base address and the interrupt. AUTO: BIOS switches on the COM. Resources are assigned in the OS per reconfiguration. 194 Onboard Ethernet 1: Enable or disable the onboard Ethernet 1 interface.
Detailed descriptions 16.4 BIOS Setup Advanced menu > SATA/PATA Configuration Figure 16-9 "SATA/PATA Configuration" submenu Entry Meaning SATA Controller Enable or disable the SATA and PATA controllers.
Detailed descriptions 16.4 BIOS Setup Advanced menu > Video Configuration Figure 16-10 Submenu Advanced menu > Video Configuration 196 Entry Meaning Primary video device Selection of the primary video interface to which the boot messages are to be output: IGD: Internal onboard graphics PEG: PCIExpress graphics (internal graphics is deactivated) PCI: PCI graphics (internal graphics is deactivated) IGD boot type Selection of the video device that is used during booting.
Detailed descriptions 16.4 BIOS Setup Advanced menu > USB Configuration Figure 16-11 Submenu Advanced menu > USB Configuration Entry Meaning USB Port0 -10 Enable: USB port is activated. Auto: USB port is deactivated when no device is plugged. Disable: USB port is deactivated. The following table lists the assignment of the USB ports to the USB interfaces: USB port USB interface 0 Ext. interface X60 P1 1 Ext. interface X60 P2 2 Ext. interface X60 P3 3 Ext. interface X60 P4 6 Int.
Detailed descriptions 16.4 BIOS Setup Advanced menu > Chipset Configuration Figure 16-12 Submenu Advanced menu > Chipset Configuration 198 Entry Meaning Port 80h Cycles Output Port 80 status display to PCI bus or LPC BUS (status display at the device).
Detailed descriptions 16.4 BIOS Setup Advanced menu > CPU Configuration Figure 16-13 Submenu Advanced menu > CPU Configuration Entry Meaning TXT Enable or disable INTEL Trusted Execution Technology. Turbo Mode Enable or disable Turbo Modes. CMP support Auto: Multi Core operation, if available Disabled: Single Core operation HT Support Auto: Use hyperthreading, if available. Disabled: Hyperthreading disabled. Use XD Capability Enable or disable XD (Execute Disable) Capability.
Detailed descriptions 16.4 BIOS Setup Advanced menu > Active Management Technology Support Figure 16-14 Submenu Advanced menu > Active Management Technology Support 200 Entry Meaning Intel AMT Support Activate/Deactivate the BIOS support for Intel Active Management Technology (AMT) Intel AMT Setup Prompt Activate/Deactivate the acknowledge prompt for calling the AMT setup Intel AMT Password Write Activate/Deactivate AMT password write protection.
Detailed descriptions 16.4 BIOS Setup 16.4.6 Security menu In this menu access to the IPC can be limited or prevented by assigning passwords (Supervisor / User password).
Detailed descriptions 16.4 BIOS Setup 16.4.7 Power menu The behavior of the device after a power failure and after wake events is specified in this menu. Figure 16-16 Power menu 202 Entry Meaning Wake on LAN Enable Device can be activated by an event via LAN. Wake on PME The device switches on when a Power Management Event occurs. Wake on Time The device switches on at a moment to be specified when it is in the operating state S5.
Detailed descriptions 16.4 BIOS Setup 16.4.8 Boot Menu In this menu this booting behavior of the device is specified and the boot medium or sequence of the boot media is determined. Figure 16-17 Boot Menu Entry Meaning UEFI Boot Enable or disable the UEFI Boot functionality. Quick Boot Enable or disable If enabled, the programming device starts faster because various hardware function tests are skipped. Quiet Boot Booting is carried out in text mode.
Detailed descriptions 16.4 BIOS Setup Boot menu > Legacy: Standard Figure 16-18 Submenu "Boot / Legacy / Normal Boot Menu " 204 Entry Meaning Entry Meaning Normal Boot Menu Boot Type Order Submenu for setting the boot order of component groups relative to one another Hard Disk Drive Submenu for setting the boot order within the hard disk group CD/DVD ROM Drive Submenu for setting the boot order within the group of optical drives.
Detailed descriptions 16.4 BIOS Setup Boot menu / Legacy / Normal Boot Menu (Advanced) In this menu all the connected bootable components and their booting position are displayed. The booting position of the component can be moved freely. During booting the component at the first position (highest booting priority) is used. If the component is not available, booting is carried out from the next component in the list.
Detailed descriptions 16.4 BIOS Setup Bootable components that are disconnected from and then reconnected to the PC between booting processes are set by the BIOS to the first position in the case of the "Advanced" setting, and relocated back to their original booting position (Advanced Placeholder Boot) in the case of the "Advanced Placeholder" setting. The boot sequence is changed as follows: Select the boot component with the ↑↓ keys, move to the desired position with + or -.
Detailed descriptions 16.4 BIOS Setup 16.4.10 Exit menu You always exit BIOS Setup in this menu. Figure 16-22 The "Exit" menu (example) Entry Meaning Exit Saving Changes All the parameter changes are saved. Afterwards a system restart is carried out with the new parameters. Exit Discarding Changes All the parameter changes are discarded and the system is restarted with the old parameters. Load Setup Defaults All parameters are set to safe values.
Detailed descriptions 16.4 BIOS Setup 16.4.11 BIOS Setup default settings Documenting your device configuration If you have changed any default settings in Setup, you can enter them in the following table. You can then refer to these entries for any future hardware modifications. Note Print out the table below and keep the pages in a safe place once you made your entries. Note The default setup settings vary depending on the ordered device configuration.
Detailed descriptions 16.
Detailed descriptions 16.
Detailed descriptions 16.
Detailed descriptions 16.5 Communications processor CP 1616 onboard 16.5 Communications processor CP 1616 onboard 16.5.1 Introduction 16.5.1.1 Properties The CP 1616 onboard allows the connection of industrial PCs to Industrial Ethernet.
Detailed descriptions 16.5 Communications processor CP 1616 onboard 16.5.1.3 Typical Communication Partners CP 1616 onboard as an IO controller The following diagram shows a typical application: CP 1616 onboard as PROFINET IO controller on the IO controller layer. The IO base controller user program runs on the PC. This program accesses the functions of the IO base user program interface.
Detailed descriptions 16.5 Communications processor CP 1616 onboard 16.5.2 Firmware loader Scenario for using the firmware loader The CP 1616 onboard is supplied with the latest version of the firmware. If new functions become available due to product development, you can make them available by performing a firmware download. Description This section will familiarize you with the application area and use of the firmware loader.
Detailed descriptions 16.5 Communications processor CP 1616 onboard 16.5.2.1 Loading firmware Start downloading procedure 1. In the Windows Start menu, select the menu command SIMATIC > STEP 7 > NCM S7 > Firmware Loader. 2. Click "Next" and follow the instructions in the dialog fields that follow. A help function is integrated in the software as support. CAUTION Ensure that the loader file you are using for the update is suitable for the version of firmware on your module.
Detailed descriptions 16.5 Communications processor CP 1616 onboard Figure 16-23 Advanced menu Peripheral Configuration Example The lower MAC address at "Onboard Profinet" is provided for Layer 2 communication, while the second one is used for Ethernet/PROFINET communication. 16.5.3 Further actions in STEP 7/NCM PC Configuring Your PC is now ready, although you still have to configure the SIMATIC NET communication software.
A Appendix A.1 Certificates and guidelines A.1.
Appendix A.1 Certificates and guidelines Low-voltage directive The device with AC power pack complies with the requirements of EC directive 2006/95/EC (Low-Voltage Guidelines). Conformance with this directive has been verified according to EN60950-1:2001 +A11:2004. The device with DC power pack also complies with this standard but does not fall within the area of validity of the EU low-voltage directive.
Appendix A.1 Certificates and guidelines Approvals for the USA, Canada and Australia Product safety The following approval is available for the device: Underwriters Laboratories (UL) to Standard UL 60950-1, Report E11 5352 and Canadian Standard C22.2 no. 60950-1 (I.T.E), or to UL508 and C22.2 no. 142 (IND.CONT.
Appendix A.1 Certificates and guidelines cULus approval, Hazardous Location +$= /2& CULUS Listed 7RA9 INT. CONT. EQ. FOR HAZ. LOC. Underwriters Laboratories Inc., complying with ● UL 508 (Industrial Control Equipment) ● CSA C22.2 No. 142 (Process Control Equipment) ● UL 1604 (Hazardous Location) ● CSA-213 (Hazardous Location) APPROVED for Use in ● Cl. 1, Div. 2, GP. A, B, C, D T4A ● Cl. 1, Zone 2, GP.
Appendix A.1 Certificates and guidelines Electrostatic charging Anyone who is not connected to the electrical potential of their surroundings can be electrostatically charged. The figure below shows the maximum electrostatic voltage which may build up on a person coming into contact with the materials indicated. These values correspond to IEC 801-2 specifications.
Appendix A.
B List of Abbreviations/Acronyms B.
List of Abbreviations/Acronyms B.
List of Abbreviations/Acronyms B.
List of Abbreviations/Acronyms B.1 Abbreviations Abbreviation Term Meaning UXGA Ultra Extended Graphics Array Graphic standard, maximum resolution 1.600 x 1.200 pixels V.24 ITU-T standardized recommendation for data transfer via serial ports VGA Video Graphics Array VRM Voltage Regulator Module WD Watchdog Program monitoring with error detection and alarming. XGA Extended Graphics Array Graphic standard, maximum resolution 1.
Glossary Automation system (AS) The programmable logical controllers (PLC) of the SIMATIC S7 system consist of a central controller, one or more CPUs, and various I/O modules. Backup Duplicate of a program, data carrier or database, used either for archiving purposes or for the protection of vital and non-replaceable data against loss when the working copy is corrupted.
Glossary COM interface The COM interface is a serial V.24 interface. The interface is suitable for asynchronous data transfer. Configuration files These are files containing data which define the configuration after restart. Examples of such files are CONFIG.SYS, AUTOEXEC.BAT and the registry files . Configuration software The configuration software updates the device configuration when new modules are installed .
Glossary Energy options The energy options can be used to reduce energy consumption of the computer, while keeping it ready for immediate use. This can be configured in Windows by selecting Settings > Control Panel > Energy options. ESD guidelines Directive for using electrostatic sensitive components. Ethernet Local network (bus structure) for text and data communication with a transfer rate of 10/100 Mbps.
Glossary Legacy USB support Support of USB devices (e.g. mouse, keyboard) on the USB ports without driver. License key The license key represents the electronic license stamp of a license. Siemens provides the license keys for protected software. License key diskette The license key diskette contains the authorizations or license keys required to enable protected SIMATIC software.
Glossary Plug&Play Generally, a reference to the ability of a computer to automatically configure the system for communication with peripheral devices (for example monitors, modems or printers). The user can plug in a peripheral and ”play” it at once without manually configuring the system. A Plug&Play PC requires both a BIOS that supports Plug&Play and a Plug&Play expansion card. POST Self-test performed by the BIOS after the computer is switched on.
Glossary Reset Hardware reset: Reset/restart of the PC using a button/switch. Restart Warm start of a computer in operating state without switching off the power supply (Ctrl + Alt + Del) Restore DVD The Restore DVD is used to restore the system partition or the entire hard disk to factory state if the system has crashed. The bootable DVD contains all the necessary image files. You can also create a boot disk allowing restoration via the network.
Index ２ Ｃ 24 V DC power supply, 37 Connecting, 40 Care, 90 CE marking, 3, 217, 218 Characteristics, 18 Check list, 51 CheckLanguageID, 72 Chip set, 168 Clamping frame Seal, 33 Cleaning, 91 Front membrane, 91 Stainless steel front, 91 Cleaning agents, 89 Cleaning guidelines, 90, 92 COA label, 23 Commissioning, 13, 51 Device, 51 Compact Flash card, 35, 106 Partitions, 126 Removing, 108 Computer unit Separating from the control unit, 94 Condensation, 13, 51 Connecting, 11, 64, 218 24 V DC power supply, 40 D
Index IP65 degree of protection, 26 Design Bus board, 181 Motherboard, 167 Design guidelines, 218 Device, 46, 51, 64 Commissioning, 51 Connecting, 46 Connecting an S7 automation system, 46 Couple, 46 Couple via MPI/PROFIBUS, 46 Open, 97 Separating, 95 Switching on, 64 Device configuration, 208 Device driver CP16xx.
Index Ｇ Graphics, 168 Ｈ Hard disk drive Removing, 104 Hard disk drives, 19 Partitions, 57, 58 Hotfix, 13 Ｉ I/O addresses Assignment, 185 Assignment, 185 I/O front ports, 180 Identification data, 22 IEC power connector, 36 Image creating, 132 Immunity to interference, 29 Installation Burner / DVD software, 131 Installation information, 23 Stainless steel front, 25 Integration Ethernet, 45 PROFIBUS, 45 PROFINET, 45 Interface, 46 MPI/DP interface, 46 USB, 56 Interfaces assignment on the motherboard COM2 (X3
Index Numeric keys, 78 Ｏ On / Off switch, 63, 64 Open Device, 97 Operating, 82 Touch panel, 82 Operating status, 17, 18 Operating system Updates, 131 Windows 7, 123 Windows XP Embedded, 126 Windows XP Professional, 123 Operating systems, 20 Operator panels, 36 Ｐ Package contents, 22 Checking, 22 Packaging, 21 Checking, 21 Removing, 21 Partitioning Windows XP Embedded, 126 Windows XP Professional, 127 Partitions Hard disk drives, 57, 58 PC Wizard, 53 PCI hardware interrupt, 188 Peripheral, 56 Peripheral C
Index Resistance to chemicals, 14, 90, 92 Restore CD, 121 Restore DVD, 122 Restoring factory state, 121 RJ45 Ethernet, 172 Ｓ Safety information, 11 SATA/PATA Configuration, 195 Scope, 3 Scope of maintenance, 90 Screen saver, 14 Seal, 33 Self-test, 51, 65 Separating Device, 95 Serial port, 35 Shipping, 16 ESD, 16 SIMATIC NET, 46 SIMATIC PC Wizard, 53 Start screen, 53 starting, 53 SIMATIC S7, 45, 46 Integration, 45 Slide-in labels, 20 Slot cover, 99 Softkey, 79 labeling, 79 Softkey row, 79 Software, 13 Spar
Index Windows XP Professional Partitioning the hard disk, 127 Reinstalling the operating system, 122 Wizard, 53 238 SIMATIC IPC677C Operating Instructions, 05/2010, A5E02722710-01
