Operating Instructions Edition 04/2006 SIMATIC Industrial PC SIMATIC Panel PC 577 Industrial PC Panel PC 577 simatic DOCUMENTATION
Preface Safety instructions and general notes 1 SIMATIC Description 2 Industrial PC SIMATIC Panel PC 577 Planning use 3 Installation 4 Connecting 5 Commissioning 6 Operation and configuration 7 Operating 8 Integration in TIA 9 Operating Instructions Servicing and maintenance 10 Alarm, error and system messages 11 Troubleshooting and FAQs 12 Technical specifications 13 Detailed descriptions 14 Appendix Release 04/2006 A5E00798484-01 A
Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. Danger indicates that death or severe personal injury will result if proper precautions are not taken.
Preface This manual Purpose of the manual This manual provides information based on the requirements defined by DIN 8418 regarding mechanical engineering documentation. This information relates to the device, its place of use, transport, storage, installation, use and maintenance. This manual is intended for the following target groups: • Users • Commissioning engineers • Service technicians • Maintenance technicians Please read the section "Safety instructions and general notes" carefully.
Preface Related documentation The documentation for the Panel PC includes the following sections: • SIMATIC Panel PC 577, Operating Instructions (compact) with the following information: – Commissioning – Legal information • SIMATIC Panel PC 577, Operating Instructions The documentation is supplied with the Panel PC in electronic form as a PDF file on the "Documentation & Drivers" CD. QuickStart for the Panel PC 577 is also supplied in printed form.
Preface Trademarks All names labeled with ® symbol are registered trademarks of Siemens AG. Other names used in this documentation may be trademarks, the use of which by third parties for their own purposes could violate the rights of the owner.
Preface Technical support You can reach the technical support for all A&D products via the support request form on the web: • http://www.siemens.com/automation/support-request • Phone: + 49 180 5050 222 • Fax: + 49 180 5050 223 Additional information about our technical support is available in the Internet at: http://www.siemens.com/automation/service Service & support on the Internet In addition to our documentation, we offer our complete knowledge base on the Internet at. http://www.siemens.
Table of contents Preface ...................................................................................................................................................... iii 1 2 3 4 Safety instructions and general notes ..................................................................................................... 1-1 1.1 Safety instructions...................................................................................................................... 1-1 1.
Table of contents 5 6 7 8 viii Connecting ............................................................................................................................................. 5-1 5.1 Overview .................................................................................................................................... 5-1 5.2 5.2.1 5.2.2 Interfaces....................................................................................................................................
Table of contents 9 10 11 12 13 Integration in TIA .................................................................................................................................... 9-1 9.1 Industrial communications ......................................................................................................... 9-1 9.2 PROFIBUS/MPI interface and WinAC card ............................................................................... 9-2 Servicing and maintenance........................
Table of contents 14 A Detailed descriptions ............................................................................................................................ 14-1 14.1 Overview of the Panel PC 577 motherboard ........................................................................... 14-1 14.2 Riser card ................................................................................................................................. 14-2 14.3 Touch sensor ..................................
Safety instructions and general notes 1.1 1.1 1 Safety instructions Warning Emergencies In the event of a device fault, remove the mains connector immediately. Inform the customer service personnel responsible. Malfunctions can occur when the operator controls or power cable are damaged or when liquids or foreign objects penetrate the device. Caution Please observe the safety instructions on the back of the cover sheet of this documentation.
Safety instructions and general notes 1.1 Safety instructions System expansions Only install system expansion devices designed for this device. The installation of other expansions can damage the system and violate the radio-interference suppression regulations. Contact your technical support team or where you purchased your PC to find out which system expansion devices may safely be installed. Caution If you install or exchange system expansions and damage your device, the warranty becomes void.
Safety instructions and general notes 1.1 Safety instructions ESD guidelines Modules containing electrostatic sensitive devices (ESDs) can be identified by the following label: Strictly follow the guidelines mentioned below when handling modules which are sensitive to ESD: • Always discharge your body´s static electricity before handling modules which are sensitive to ESD (for example, by touching a grounded object). • All devices and tools must be free of static charge.
Safety instructions and general notes 1.1 Safety instructions Electrical connection Warning Disconnect the device from the mains before every intervention. Do not touch power cables or data transmission cables during electrical storms and do not connect any cables. High frequency radiation Caution Unintentional operating situations High frequency radiation, e.g. from cell phones, can cause unintentional operating situations under some circumstances.
Safety instructions and general notes 1.2 General information, download "Panel PC" 1.2 1.2 General information, download "Panel PC" Overview Caution The device is approved for operation in closed rooms only. The guarantee is void if this stipulation is ignored. Avoid extreme environmental operating conditions. Protect your device against dust, moisture and heat. For additional information, refer to the Technical data. Do not place the device in direct sunlight.
Safety instructions and general notes 1.2 General information, download "Panel PC" Caution Condensation When transporting the device in low temperatures, ensure that no moisture gets on or into the device. This also applies if the device is subjected to extreme changes in temperature. Commissioning Allow the device to slowly adjust to room temperature before commissioning the device. Do no place the device near direct heat radiation.
Safety instructions and general notes 1.2 General information, download "Panel PC" Safety-relevant applications Warning Maloperation Do not perform safety-relevant functions of the user software with the touch screen. Chemical resistance Caution Adhere to the information regarding chemical resistance. Please refer to the "Tools & Demosoftware" Internet site for more information. Enter "Chemical resistance" as the search term. The available articles are displayed.
Safety instructions and general notes 1.2 General information, download "Panel PC" Burn-in effect on TFT displays A permanent picture with bright images can lead to a burn-in effect on the TFT LCD. If a screen saver is activated, please observe the following: • The liquid crystals in screen savers which actuate active black when the backlighting is on, e.g. flying stars "starfield simulation," renew themselves. Pay attention to the length of time the backlighting is activated.
Description 2.1 2.1 2 Application features Introduction The Panel PC 577 provides a high standard of quality based on the protection type of the control unit, high-level EMC and CE certification for industrial application. The device is designed for 24 hour operation. Further information is available in the section "Ambient and environmental conditions of the "Technical data" chapter.
Description 2.2 Design 2.2 2.2 Design The device serves as a base for PC-based HMI devices, the Panel PCs. The Panel PC 577 fulfills the basic requirements for industrial compatibility and provides high performance at a low price. The device consists of the control unit with a key or touch panel and the computer unit. The control unit is screwed to the back of the computer unit.
Description 2.3 Technical features 2.3 2.3 Technical features General features Processor - Intel® Pentium 4 2.4 GHz - Intel® Celeron 2.0 GHz Chipset Intel 865G Main memory 256 MB = 2 x 128 MB SDRAM or 1 x 256 MB SDRAM 512 MB = 2 x 256 MB SDRAM 4 slots, expandable to 4 GB maximum Slots for add-ons • • Device variants The device is available with different control units which are distinguished by the size of the display and by a membrane keyboard or touch screen.
Description 2.3 Technical features Interfaces Installed via expansion cards: PROFIBUS / MPI CP 5611-compatible (not included in the scope of supply) Ethernet LAN 10/100/1000 Mbps USB 4x USB 2.0 high current, external 2x USB 2.0 high current available, internal via male connector Serial interfaces COM1 V.24 Parallel interfaces LPT1 Keyboard PS/2 Mouse PS/2 1x USB 2.
Description 2.
Description 2.
Planning use 3.1 3.1 3 Overview Introduction This section describes the first steps after unpacking, the permitted mounting positions and the fixation. This section describes the necessary considerations for EMC. Field of application The Panel PC is an industry-standard PC platform for demanding tasks in the field of PCbased automation.
Planning use 3.2 Unpacking and checking the delivery 3.2 3.2 Unpacking and checking the delivery Procedure 1. Please check the packaging material for transport damage upon delivery. 2. If any transport damage is present at the time of delivery, lodge a complaint at the shipping company in charge. Have the shipper confirm the transport damage immediately. 3. Unpack the device. Caution Do not lie the device on its back. This will avoid any damage to an optical drive which may be present.
Planning use 3.2 Unpacking and checking the delivery Warning Risk of damage Do not transport the device when it is mounted. During transport, use the hard disk transport lock (if present).
Planning use 3.3 Make note of identification data 3.3 3.3 Make note of identification data Procedure 1. Write down the Microsoft Windows product key of the Certificate of Authenticity COA in the table at the end of this section. The product key can be found on the back of the device. You will need the product key during the reinstallation of the operating system. 2. Write down the manufacturer's number SVP and the order number , e.g. "6AV782...", in the table.
Planning use 3.4 EMC directive 3.4 3.4 EMC directive Electromagnetic compatibility The device fulfills the requirements of the EMC law of the Federal Republic of Germany as well as the EMC directive of the Single European Market. The device is designed as a built-in model with front-sided IP65 degree of protection. Ensure compliance with the EN 61000-4-2 standard by installing the device in grounded metal cabinets, e.g. 8 MC cabinets, Siemens catalog NV21.
Planning use 3.5 Mounting positions and fastening 3.5 3.5.1 3.5 Mounting positions and fastening Installation instructions Before mounting the device, read the following general notes relating to installation. Warning Dangerous Voltage Isolate the power supply to the control cabinet before opening it. Ensure that the power to the control cabinet cannot be turned on accidentally. Caution The device is approved for operation in closed rooms only.
Planning use 3.5 Mounting positions and fastening • Also provide enough free space to add on to the device. • Equip the control cabinet with struts for stabilizing the mounting cut-out. Install struts where necessary. • Avoid extreme environmental operating conditions. Protect your device against dust, moisture and heat. • Install the device in such a way that it poses no danger, e.g. by falling over. • During assembly, please comply with the approved mounting positions.
Planning use 3.5 Mounting positions and fastening 3.5.2 Permitted mounting positions Approval Only certain mounting positions are approved for the device. Figure 3-2 Permitted mounting position The device can be mounted in a vertical position with deviations between +5° and -5° in the given directions. 3.5.3 Mounting type The control unit is secured in the mounting cut-out either with clamps or screws. Notice Securing with screws is not possible with the 12" touch screen variant.
Planning use 3.5 Mounting positions and fastening 3.5.4 Degree of protection Principle The degree of protection provided at the front is assured when the mounting seal lies completely against the mounting cut-out. Caution Please ensure that the material strength at the mounting cut-out is a maximum of 6 mm. Please follow the specifications for the dimensions in the "Mounting cut-out" section.
Planning use 3.6 Mounting cut-out 3.6 3.6.1 3.6 Mounting cut-out Selecting and creating the mounting cut-out Requirement The degree of protection suitable to the field of application and thereby the mounting method have been selected. Procedure 1. Follow the installation instructions. 2. Select a location suitable for installation, taking into account the installation instructions and the chosen mounting position. 3.
Planning use 3.6 Mounting cut-out 3.6.2 Dimensions The following illustration shows the dimensions for the mounting cut-out. You can also obtain these dimensions from the mounting template supplied with the device.
Planning use 3.6 Mounting cut-out Table 3-1 Dimensions for the mounting cut-out in mm Control units L1 L2 L3 1) L4 1) L5 L6 2) L7 L8 2) L9 2) A1 A2 S1 S2 S3 S4 S53) S63) S73) Tolerance +1 +1 ±0.2 ±0.2 ±0.5 ±0.5 ±0. 5 ±0.
4 Installation 4.1 4.1 Securing with clamps Scope Skip this step if you have selected "screw mounting." Note The 12" touch screen variant can only be fixed in place using clamps. Requirement • The mounting cut-out has been completed. • Clamps are readily available in the accessories. Clamps and setscrews are included in the contents of delivery. Figure 4-1 Clamp assembly Procedure 1. Follow the installation instructions. 2. Working from the front, insert the device into the mounting cut-out. 3.
Installation 4.2 Securing with screws 4.2 4.2 Securing with screws Scope Skip this step if you have selected "clamp mounting." Notice Securing with screws is not possible with the 12" touch screen variant. For securing the 19'' touch screen variant with screws, you will need the accessory with MLFB No. 6AV7672-8KE00-0AA0 Requirement The mounting cut-out has been completed.
Installation 4.2 Securing with screws Procedure 1. Follow the installation instructions. 2. Drill suitable holes at the prepared mounting cut-out in accordance with the specifications for L4 and L5, as shown in the mounting cut-out in the dimensions. 3. Carefully drill the respective holes in the control unit at the designated location (1) from the rear. Figure 4-2 Designated location for holes on the control unit 4. Working from the front, insert the device into the mounting cut-out. 5.
Installation 4.3 Dimensions 4.3 4.3 Dimensions The mounting depth increases by 28 mm when a DVD-ROM drive is installed in the device. Refer to the dimensional drawings in the "Technical specifications" section for the exact measurements.
Connecting 5.1 5.1 5 Overview Introduction Once you have mounted the device, connect it. Warning Do not touch power cables or data transmission cables during electrical storms and do not connect any cables. Unplug the mains connector from the socket to be sure the electricity is disconnected. Caution Connection sequence Follow the described sequence when connecting the device to avoid damaging it. Commissioning Allow the device to adjust to the room temperature before connecting the device.
Connecting 5.1 Overview Procedure 1. Connect the equipotential bonding. 2. Connect peripherals: – Connect an external monitor if desired. – Connect the PS/2 mouse. – Connect the PS/2 keyboard. – Connect a USB device such as a USB mouse if desired. – Connect a printer. 3. Connect the power supply.
Connecting 5.2 Interfaces 5.2 5.2.1 5.2 Interfaces Front interfaces Introduction A USB interface is located on the front side. For more information, please refer to the chapter "Operation." Attach an external keyboard or an external mouse, for example, to the USB interface. The front-side USB interface supports the standard USB 2.0. Caution Wait at least 10 seconds between the unplugging and replugging of USB devices.
Connecting 5.2 Interfaces 5.2.2 Rear interfaces Interfaces Arrangement of the interfaces 5-4 Item Name Description (1) KEYBOARD Connection for a PS/2 keyboard (2) Mouse Connection for a PS/2 mouse (3) USB 2.0 Connection for USB devices (4) COM 1 Serial interface, 9-pin Sub-D connector (5) LPT 1 Parallel interface, 25-pin sub D socket (6) VGA VGA connection (7) USB 2.
Connecting 5.2 Interfaces Power supply Position of the IEC power connector Description IEC power connector (2) for the AC power supply to the device. The maximum permitted power supply range is 120 V AC to 230 V AC. On / Off switch (1) Note You can also switch on the device using the soft power key. Refer to the "Operator controls" chapter for more information.
Connecting 5.3 Connecting peripherals 5.3 5.3.1 5.3 Connecting peripherals Overview When connecting the device for the first time, connect a PS/2 keyboard and PS/2 mouse. Connect any required USB components such as a USB hub. Caution Disconnect the device from the power supply before connecting peripherals. This does not apply to connecting and disconnecting USB devices. Connect only I/O modules approved for industrial applications according to EN 61000-62:2001.
Connecting 5.3 Connecting peripherals 5.3.3 USB Introduction Commercially available USB peripherals can be easily and flexibly connected via the USB interface. For example, you can connect an external USB keyboard and a USB mouse. If the USB keyboard has a USB interface, you can connect other USB peripherals, such as a USB mouse, directly to the keyboard. USB interface There are several types of USB peripherals: • Low power devices: maximum 100 mA power consumption, e.g.
Connecting 5.3 Connecting peripherals Connecting USB devices Caution Wait at least 10 seconds between removal and reconnection of USB devices. This also applies to control units with touch screens, especially for touch operation. Notice When using standard USB peripherals, please bear in mind that their EMC immunity level is frequently designed for office applications only. These devices are adequate for commissioning and servicing purposes.
Connecting 5.4 Connecting the power supply 5.4 5.4 Connecting the power supply Principle The device can be optionally operated on 110 or 230 V AC systems. The device features an automatic voltage switch and a power switch. Caution Do not touch power cables or data transmission cables during electrical storms and do not connect any cables. Unplug the mains connector from the socket to be sure the electricity is disconnected. The device features a safety-certified power cable.
Connecting 5.4 Connecting the power supply For USA and Canada: A UL-listed power supply cable must be used in the United States and Canada. 110V power supply Use a flexible cable with the following characteristics: • UL approval • Type SJT with three conductors • At least 18 AWG conductor cross-section • Maximum 4.5 m length • Parallel grounding plug 15 A, min.
Connecting 5.5 Uninterruptible AC power supplies 5.5 5.5 Uninterruptible AC power supplies Introduction This chapter describes the considerations involved in using an uninterruptible AC power supply (AC UPS) for the Panel PC. Due to legal regulations related to reducing reactive-power consumption in public and private electrical networks, all AC voltage supplies in Panel PCs feature a power factor correction (PFC) circuit. Technically, there is passive PFC and active PFC.
Connecting 5.6 Connecting the equipotential bonding 5.6 5.6 Connecting the equipotential bonding A low-resistance ground connection ensures that interference signals generated by external power supply cables, signal cables or cables to the I/O modules are safely discharged to ground.
Connecting 5.6 Connecting the equipotential bonding Avoiding differences in potential Differences in potential arise between separated system parts, which in some cases lead to high equalization currents. This situation may arise if the cable shielding is terminated at both ends and grounded at different system parts. Potential differences can be caused, for example, by different power inputs.
Connecting 5.
Connecting 5.
Commissioning 6.1 6.1 6 Removing the transport lock for the hard disk Note Not every device has a hard disk transport lock. To enhance the ruggedness of the SIMATIC Panel PC 577 during shipping, the device is fitted with a transport lock for the hard disk. This comprises two knurled screws that clamp the hard disk to prevent undesirable vibrations. The hard disk transport lock is located on the top of the SIMATIC Panel PC 577 and is marked with an adhesive label.
Commissioning 6.1 Removing the transport lock for the hard disk Removing the transport lock for the hard disk Procedure for removing the transport lock for the hard disk (1) Unscrew 2 knurled screws (1) by hand +DUG 'LVN 7UDQVSRUWVLFKHUXQJ ELWWH YRU GHU ,QEHWULHEQDKPH HQWIHUQHQ [ 5¦QGHOVFKUDXEHQ 3OHDVH UHPRYH WKH KDUG GLVN WUDQVSRUW ORFN EHIRUH RSHUDWLQJ (2) Screw the knurled screws into the nuts on the rear of the device for safe-keeping.
Commissioning 6.2 Overview 6.2 6.
Commissioning 6.2 Overview Procedure 1. Switch on the device. 2. Install Microsoft Windows operating system. 3. Install the applications and drivers.
Commissioning 6.3 Switching on the device. 6.3 6.3 Switching on the device. Procedure 1. Plug the mains connector of the supplied power supply cable in the AC power supply connector of the device. 2. Screw on the lock for the mains connector (1). Figure 6-1 Lock mains connector 3. Lock the mains connector in place as shown in the illustration. 4. Plug the power supply cable into a socket with a grounded protective conductor. 5. Switch on the power switch of the device.
Commissioning 6.3 Switching on the device. Self-test After connection to the power supply, the device performs a self test. During the self test, the message "Press to enter SETUP" appears briefly. When the self-test is finished, the operating system will be loaded.
Commissioning 6.4 Setting up the Microsoft Windows operating system 6.4 6.4 Setting up the Microsoft Windows operating system Introduction The setup wizard appears immediately following the startup of the device. The wizard is used to set the parameters of the operating system. Note The dialogs of the setup wizards differ slightly in some places for the Windows 2000 Professional and Windows XP Professional operating systems. In order to change to the next dialog, click on the ">>" button.
Commissioning 6.5 Installing applications and drivers, Touch-Base 6.5 6.5 Installing applications and drivers, Touch-Base Introduction After the device is restarted, different dialogs appear on the screen. Drivers and applications can be installed from these dialogs. Additional hardware and software components You can install and configure additional hardware and software components such as a network. For additional information, refer to the documentation of the hardware and software.
Commissioning 6.5 Installing applications and drivers, Touch-Base Procedure 1. In the "Panel Wizard" dialog, click the type of panel that corresponds to your device. Figure 6-2 Panel Wizard, selection of the panel type 2. In the "Panel Wizard Touch" dialog, click on the screen size that corresponds to your device. The screen resolution is set correspondingly for the device.
Commissioning 6.5 Installing applications and drivers, Touch-Base Figure 6-3 Panel Wizard Touch, selection of the screen size The next step only applies to control units with touch screen panels. Once the screen size is selected, the wizard will search for new hardware, the touch controller. The Panel Wizard closes and the Touch-Base-25-point touch calibration appears. Carry out the following steps carefully.
Commissioning 6.5 Installing applications and drivers, Touch-Base 3. Briefly touch the touch screen at every cross hair. Figure 6-4 Touch screen calibration 4. The following only applies to control units with key panels: Exit the operating system session and restart the device. Otherwise the "Security features" from "KeyTools" will not be activated. Warning Use "KeyTools" as described in the "Additional drivers and applications" section of the "Operation and configuration" chapter.
Commissioning 6.5 Installing applications and drivers, Touch-Base The installation of the drivers and applications is complete. Further information is available in the "Operation and configuration" chapter of the operating instructions under the section, "Additional drivers and applications.
Commissioning 6.6 Notes about new installation of Windows 2000 6.6 6.6 Notes about new installation of Windows 2000 Service pack After a new installation of Windows 2000, install at least Service Pack 4. Service Pack 4 is supplied in the product package. Note If you are using SIMATIC WinCC or SIMATIC WinCC flexible, pay heed to the operating system releases. For additional information, refer to the SIMATIC WinCC and SIMATIC WinCC flexible documentation.
Commissioning 6.
Operation and configuration 7.1 7.1.1 7.1 7 Normal operation Switching the device on and off Switching on the device Requirement • The I/O modules, e.g. mouse and keyboard, have been connected. Caution Use shielded cables and metal connectors to connect peripherals. Otherwise, the specified standards and specifications declared by Siemens AG are no longer valid. Secure the plugs of the interface cables to the device housing with screws. This improves the electrical shielding.
Operation and configuration 7.1 Normal operation Procedure Warning Danger of maloperation! The following applies to external input devices or combinations of external input devices and control units with key panels: Ambiguous key codes can cause serious malfunctions of the application program. Always activate the "Security features" of "KeyTools." Please follow the relevant safety instructions in the chapter "Additional drivers and applications.
Operation and configuration 7.1 Normal operation Switching off the device Shut down the operating system correctly before switching off the device. Caution Wait for the display to go dark. Then switch off the power switch of the device. Warning Always pull out the power cable to isolate the device from the mains.
Operation and configuration 7.2 Additional drivers and applications 7.2 7.2.1 7.2 Additional drivers and applications Overview The necessary drivers and applications are contained in the supplied "Documentation and Drivers" CD. Note The supplied drivers and applications have been system-tested and are approved for this device. No warranty can be provided for other software. Press the "Help" button to obtain information concerning the buttons of a dialog.
Operation and configuration 7.2 Additional drivers and applications 7.2.2 Setting the touch screen Call • Start menu "Start", command "Programs > UPDD > Settings" Function Recalibrates the touch screen. If the touch screen does not react as expected when touched, repeat the calibration. To do this, first activate the 25 point calibration and then calibrate the touch screen. Figure 7-1 Touch defaults, "Calibration" tab Note For further information press the "Help" button.
Operation and configuration 7.2 Additional drivers and applications Special features Note When the edges of the touch screen are used intensively, it is recommended that 25 point calibration is performed instead of the 9 point calibration. Warning Maloperation If you touch the touch screen while the screen saver is active, the SIMATIC process visualization software, e.g. WinCC, will carry out the functions which happen to be behind it.
Operation and configuration 7.2 Additional drivers and applications 7.2.3 KeyTools Call Start menu "Start", command "Settings > Control panel > SIMATIC Key Tools" Function SIMATIC KeyTools is one selection of the applications for Panel PC. With it, key codes which are sent from the key panel of the control unit are adjusted. A description of the "KeyTools" is located in the "Help" menu, and more information is located in the menu "Info > About.
Operation and configuration 7.2 Additional drivers and applications 7.2.4 SystemGuard Call "SystemGuard" icon in the message field. SystemGuard is activated automatically after the device is started. Function SystemGuard indicates temperatures, fan speeds and voltages. Notice SystemGuard is a freeware tool for which Siemens AG offers no technical support. Observe the notes in the online help of the application.
Operation and configuration 7.2 Additional drivers and applications 7.2.5 TouchInput Call "TouchInput" symbol on the desktop. Function TouchInput provides a screen keyboard. On the screen keyboard, the characters are entered directly on the touch screen or with the mouse.
Operation and configuration 7.2 Additional drivers and applications 7.2.6 CheckLanguageID Scope The following applies to Windows 2000 Professional Multi-Language and Windows XP Professional Multi-Language. Call c:\drivers\checklang\checklangid.exe or reinstallation from the "Documentation and Drivers" CD. Function "CheckLanguageID" displays the currently installed languages.
Operation and configuration 7.2 Additional drivers and applications 7.2.7 Multilingual settings for the operating system Windows MultiLanguage MUI operating system enables users to set the language of the GUI to their individual preference. Some elements are not localized, however, and remain in the original language of the system - English. You should therefore always install English language service packs.
Operation and configuration 7.
8 Operating 8.1 8.1 Operator controls On / Off switch On / Off switch Description The device is on when the power switch (1) is in position "0". Voltage is supplied to the device even when it is switched off. Warning The On / Off switch does not disconnect the device from mains.
Operating 8.1 Operator controls "Soft power" key "Soft power" key Description The soft power key (1) can trigger two shutdown functions during active operation: 1) Correct shutdown of the operating system and shutdown of the device To perform this function, press the key briefly with a pointed object. 2) Immediate switch-off of the device without correct shutdown of the operating system This function is used to shut down the device when it no longer responds.
Operating 8.2 Operator controls on key panels 8.2 8.2.1 8.2 Operator controls on key panels Overview The device has the following keypads: • 2 x 8 vertical keypads with softkey functions • 2 x 10 horizontal keypads with function keys F1 -F20 The number of keys, their labeling and function is the same on all key panels. The various panel types differ only in the arrangement of the keys and in the size and type of the display.
Operating 8.2 Operator controls on key panels 8.2.2 Keyboard Principle The layout of the membrane keyboard is "English/USA international." Warning Maloperation If you activate several keys simultaneously, a malfunction on the device cannot be excluded. Activate function keys and softkeys only in sequence! Use "KeyTools" as described in the chapter "Additional drivers and applications.
Operating 8.2 Operator controls on key panels Function keys and softkeys The softkeys are arranged on the left and on the right, and the function keys in a double row below the display.
Operating 8.2 Operator controls on key panels Numeric keys Enter the numerals "0" to "9" and special characters, e.g. the decimal point, using the predefined assignment of the numeric keys. Figure 8-3 Numeric keys Enter special characters, arithmetic signs and signs Special characters, arithmetic signs and signs are also assigned to most of the alphanumeric and numeric keys. These signs are indicated by white symbols on the top left of the keys. To enter such a sign, proceed as follows: 1.
Operating 8.2 Operator controls on key panels External keyboards The keyboard layout has been set to "English/USA international." If you use a keyboard with a layout other than the "English/USA international" layout, the key codes of the internal and external keyboards might no longer correspond. 8.2.3 Labeling function keys and softkeys Scope This section applies only to control units with key panels.
Operating 8.
Operating 8.3 Operator controls of the touch screen panels 8.3 8.3.1 8.3 Operator controls of the touch screen panels Overview The 12", 15" and 19" variants differ in their dimensions and the size of the display. The 12'' and 19'' variants do not have side drill hole covers. The following figure is therefore only an example using the front view of the 15" variant.
Operating 8.3 Operator controls of the touch screen panels 8.3.2 Touch screen The display is sensitive to touch and application-specific surface elements, e.g. a button, appear on the screen. By tapping the button with your finger, the function assigned to the button is activated. Caution Only touch one point on the touch screen and not several points at one time. You may otherwise trigger unintended reactions.
Operating 8.4 DVD-ROM drive 8.4 8.4 DVD-ROM drive Introduction The DVD-ROM or DVD burner drive is used to install software during commissioning or when servicing a device. Figure 8-7 CD-ROM drive 1 Access LED 2 Eject key 3 Emergency removal aperture 4 Tray Emergency removal An emergency removal involves removing a CD when the tray is blocked or there is no power for the drive. In this case the tray can be moved manually instead of motor-driven Procedure 1.
Operating 8.5 Transferring authorizations 8.5 8.5 Transferring authorizations Note The device has no floppy disk drive. Therefore, transfer the authorizations for SIMATIC HMI software from a USB floppy disk drive. The following devices have been tested: SINUMERIK FLOPPY DISK DRIVE, order number 6FC5235-0AA05-1AA2 Caution The USB floppy disk drive is only suitable when mounted in a control cabinet.
Integration in TIA 9.1 9.1 9 Industrial communications Introduction The following options are available for integrating the device in existing or planned system environments and networks. Ethernet The integrated Ethernet interface can be used for communication and for data exchange with automation devices such as SIMATIC S7. You need a suitable software package for this. STEP7, WinCC, ProTool, WinCC flexible, WinAC, SIMATIC NET.
Integration in TIA 9.2 PROFIBUS/MPI interface and WinAC card 9.2 9.2 PROFIBUS/MPI interface and WinAC card Note You can use a CP 5613 communication module for the PROFIBUS/MPI interface. A PROFIBUS/MPI interface is also provided on WinAC cards. You can find further information in the documentation for the CP 5613 communication module and in the "Servicing and maintenance" chapter under the section "Installing and removing hardware components", "PCI/WinAC cards".
10 Servicing and maintenance 10.1 10.1 Servicing Scope of maintenance When working in areas where there is dust that may be hazardous to functionality, the device must be operated in a control cabinet with a heat exchanger or with suitable supply air. Note The dust deposits must be removed at appropriate time intervals. Maximum dust content in the air circulating in the cabinet Suspended component 0.2 mg/m3 Deposits 1.
Servicing and maintenance 10.1 Servicing Chemical resistance Caution Adhere to the information regarding chemical resistance of the panel front. Please refer to the "Tools & Demosoftware" Internet site for more information. Enter "Chemical resistance" as the search term. The available articles are displayed. Procedure 1. Switch off the device. This prevents the accidental triggering of functions when the screen is touched. 2. Dampen the cleaning cloth. 3.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2 10.2.1 10.2 Removing and installing hardware components Repairs Notice Similar to figure The images presented below deviate slightly from the actual device in some respects. Carrying out repairs Only authorized personnel are permitted to repair the device. Warning Unauthorized opening and improper repairs on the device may result in substantial damage to equipment or endanger the user.
Servicing and maintenance 10.2 Removing and installing hardware components Tools You can perform all installation tasks on the device using Torx T6, Torx T10, and Torx T20 screwdrivers and a Philips screwdriver.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.2 Opening the device Warning Do not touch power cables or data transmission lines during electrical storms and do not connect any cables. Caution Warranty period Within the warranty time, you are only allowed to install expansions for memory and expansion card modules. Requirement • If the fastening screws are not accessible due to the mounting: The device is removed from the control cabinet.
Servicing and maintenance 10.2 Removing and installing hardware components Opening the device Accessing expansion modules 1 Remove the four screws (1). Remove the 2 screws (2). 2 10-6 Lift the lid up and remove it.
Servicing and maintenance 10.2 Removing and installing hardware components Access to memory modules, processor, heat sinks, back-up battery and power supply 1 Remove the 3 screws (1). Remove 2 screws (2) from the CD-ROM drive. 3 Tilt the cover (1) CD-ROM drive (2) upward.
Servicing and maintenance 10.2 Removing and installing hardware components Closing the device Caution Avoid crimping the cables When closing the housing cover, make sure you do not crimp a cable between the fan and heat sink and that no cable is in contact with the heat sink.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.4 Removing/installing memory modules Memory expansion The motherboard is equipped with 4 slots for memory modules. This enables you to expand the memory capacity of the device to a maximum of 3 GB. Depending on the variant you have ordered, the basic configuration may include 2 X 128 MB SDRAM or 2 X 256 MB DDR400. Caution Read the information in the manual of the motherboard on the "Documentation and Drivers" CD.
Servicing and maintenance 10.2 Removing and installing hardware components Removing a memory module Steps for removing a memory module 1 Open the device. 2 Snap the interlocks (1) to the side. 3 Pull the memory module (2) upwards out of the slot. 4 Close the device. Display of the current memory expansion Changes to the memory expansion are automatically detected. The memory allocation is displayed when the device boots.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.5 PCI/WinAC cards 10.2.5.1 Notes on the modules Notes on module specifications The device is designed for use with modules conforming to AT/PCI specifications. PCI modules with 5 V and 3.3 V supply voltage can be operated. Note about long PCI modules Before long PCI modules can be inserted into the guide rails, they must be fitted with an extender (this should be supplied with the long PCI board).
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.5.2 Installing expansion modules PCI card Steps for installing a PCI card: 1 Open the device. 2 Remove the relevant steel slot cover (1) 3 Insert the expansion module (2) into the relevant slot. 4 Secure the frame with the (2, 3) card retainers • Make sure that the frame is connected to the device from the outside.
Servicing and maintenance 10.2 Removing and installing hardware components WinAC card Further information is available in the section "WinAC card" of the "Integration in TIA" chapter. Steps for installing a WinAC card 10-14 1 Open the device. 2 Remove the frame with the card retainer (2, 3): remove the 2 retaining screws (1) of the threads from the outside. 3 Unscrew the steel slot cover of the upper two slots (1). 4 Unscrew the WinAC cover plate from the outside.
Servicing and maintenance 10.2 Removing and installing hardware components Steps for installing a WinAC card 5 Place the WinAC cover plate (1) over the WinAC card from the right. Ensure that the WinAC card is inserted in the guide rail (2). 6 Insert the WinAC card into the upper slot. • Ensure that the threaded holes (3) are toward the inside. • Insert the WinAC card squarely. Ensure that the WinAC card is aligned correctly. • Insert the interfaces through the cut-outs (4) in the holding plate.
Servicing and maintenance 10.2 Removing and installing hardware components Steps for installing a WinAC card 8 Secure the frame with the (2, 3) card retainers • Make sure that the frame is connected to the device from the outside. • To adapt to different cards, the frame can be offset horizontally and secured by 2 of the 4 threaded holes (1). • Screw on the frame from the outside using the suitable threaded holes (1).
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.6 Drives 10.2.6.1 Removing and installing a DVD-ROM drive Procedure 1. Loosen the 4 screws (1). Figure 10-3 Drive with housing 2. To remove the housing of the drive, hold down the base plate (2) of the drive securely and slide the housing (3) to the right until the eyes (4) are free. 3. Lift the housing (3) from the drive. 4. Detach the IDE plug (1) and the power supply plug (2).
Servicing and maintenance 10.
Servicing and maintenance 10.2 Removing and installing hardware components 5. Loosen the 4 screws (3) that secure the drive to the base plate. 6. Lift the drive out. 7. To remove the terminal pcb, loosen the 2 screws (4). The drive is now fully removed. Figure 10-5 Removed drive Reverse the procedure to install the drive.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.6.2 Replacing the hard disk Procedure 1. Open the device. 2. Detach the plug (1) from the motherboard.
Servicing and maintenance 10.2 Removing and installing hardware components 3. Remove the 4 screws (1) while securely holding the retaining frame (2).
Servicing and maintenance 10.2 Removing and installing hardware components 4. Remove the drive from the retaining frame. 5. Loosen the 4 screws (1) that secure the drive (2) to the retaining frame.
Servicing and maintenance 10.2 Removing and installing hardware components 1. Remove the drive (2) from the bracket. 2. Detach the plug (1) from the drive. Figure 10-9 Hard disk connection Reverse the procedure to install the drive. Caution Pin connection The plug (1) is connected to the drive. Ensure that the pins of the circuit board are correctly aligned to the left when inserted into the drive (2). The two pins on the right (3) are open. The drive may otherwise malfunction.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.7 Changing processors and heat sinks Introduction To exchange the processor, first remove the heat sink. Procedure 1. Open the device. 2. Open the clips (1) of the heat sink retainer (2). Figure 10-10 Removing the heat sink 3. The heat sink retainer is hooked into the base frame from below. Unhook the heat sink retainer and lift it out. 4. Lift out the heat sink (3). The processor is now accessible. 5.
Servicing and maintenance 10.2 Removing and installing hardware components Figure 10-11 Processor 6. Lift the processor (2) out of the slot. Reverse the procedure to install the processor and hear sink. The processor will be automatically detected by the BIOS. Caution Insert the new processor into the slot so that the notch on the processor matches the marking on the processor slot (3). Swing the lever (1) downwards until it clicks into position.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.8 Replacing the back-up battery To be noted before you replace the battery Note The life span of a back-up battery is approximately 3 - 5 years, depending on the operating conditions. Caution Risk of damage The lithium battery may only be replaced with an identical battery or with a type recommended by the manufacturer.
Servicing and maintenance 10.2 Removing and installing hardware components Preparation Note The configuration data and contents of the SRAM in the device are lost when the battery is replaced. 1. Note down the current settings of the BIOS setup. A list in which you can note down this information is found in the BIOS description. 2. Isolate the device from mains and disconnect all cables. Procedure Steps for replacing the battery 1 Open the device. 2 Open the terminal clamp (1).
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.9 Removing/installing the power supply Requirement • The device is opened. • All power supply cables are unplugged. Procedure Steps for removing and installing the power supply module 1 10-28 Remove the 2 screws (1).
Servicing and maintenance 10.2 Removing and installing hardware components Steps for removing and installing the power supply module 2 Remove the screw (1). 3 Slide the power supply module (2) until the recesses for the screw (1) are free. 4 Lift out the power supply module (2). 5 Proceed in reverse order to install the new power supply module.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.10 Separating the control unit from the computer unit Introduction The control unit is separated from the computer unit to carry out repairs or to replace the control unit, for example. Procedure 1. Disconnect the device from mains. 2. Open the control cabinet. 3. Remove the device from the control cabinet. Secure the device against falling out and unscrew it.
Servicing and maintenance 10.2 Removing and installing hardware components 7. Detach the plugs (2) and (3) and also plug (4) when a 19" touch or key panel is used.
Servicing and maintenance 10.2 Removing and installing hardware components 8. The next two steps apply to control units with 12" touch panels: Loosen the 2 screws (1) that secure the computer unit to the control unit.
Servicing and maintenance 10.2 Removing and installing hardware components A fastening rail (2) with 2 female threads is located on the control unit for screws (1). Its counterpart, a fastening rail with hooks (3), is located on the computer unit. The control unit latches into these hooks. Figure 10-14 Fastening rails on the computer unit and control unit 9. Carefully swing the computer unit down until it releases from the hooks of the control unit.
Servicing and maintenance 10.2 Removing and installing hardware components 10.The next two steps only apply to control units that do not have 12" touch panels: Loosen all screws (1) which attach the computer unit to the rear of the control unit. Figure 10-15 Separating the control unit from the computer unit The control unit and the computer unit are connected to each other by a hinge joint(2) on the left of the illustration. 11.
Servicing and maintenance 10.2 Removing and installing hardware components Mounting the device To reinstall the device, follow the reverse procedure. Caution Please note the following. Device malfunctions may otherwise occur. • Ensure that the ribbon cable is plugged into the correct sockets. • Ensure that the ribbon cable is not kinked or crimped. • Check the switch settings (1). Ensure that the switch is set to match the settings in the following table.
Servicing and maintenance 10.
Servicing and maintenance 10.2 Removing and installing hardware components 10.2.11 Connecting an external monitor Introduction When exchanging the control unit or when it fails, operate an external monitor with VGA connector through the VGA interface. You can activate the monitor in the operating system setup. Procedure 1. Isolate the device from mains and switch the monitor off. Caution Damage to the device! Ensure that the device and the monitor are switched off. 2.
Servicing and maintenance 10.3 Installing software 10.3 10.3.1 10.3 Installing software Overview Introduction Recommission the device after exchanging the hard disk drive. Or reinstall the software as required. Caution Do not turn off the device during software installation. Otherwise, parts of the software which are necessary for trouble-free operation will be lost.
Servicing and maintenance 10.3 Installing software Procedure 1. Format and partition the hard disk drive as required. 2. Transfer the backed up data back to drives C and D using the backup utility. Use the Restore CD, for example, to transfer the original image back to the device's hard disk. 3. You can also install an operating system yourself. 4. Install the required Windows service packs and security updates. Refer to the "Commissioning" section for more information. 5.
Servicing and maintenance 10.3 Installing software 10.3.2 Supplied software CDs / DVDs If your software is corrupt, reinstall your software using the Restore DVD and Documentation and Drivers CD. Restore DVD: Contains a hard disk image with the factory software consisting of the operating system and installed hardware drivers. Documentation and Drivers CD: Contains the documentation and required system drivers and applications, such as Microsoft Internet Explorer and hotfixes.
Servicing and maintenance 10.3 Installing software 10.3.3 Restoring the factory state of the software using the Restore DVD Introduction With the Restore DVD, you can restore the original factory-supplied software: • Restoring the hard disk with drive "C: (system) and drive "D": • Restoring only drive "C:" This allows you to retain any user data on drive "D". . The DVD includes the necessary images and tools for this purpose.
Servicing and maintenance 10.3 Installing software Procedure 1. Place the Restore DVD in the device's drive. 2. Restart the system. 3. When the BIOS message "Press to enter Setup or to show boot menu" appears, press . After initialization, a "Boot Menu" is displayed. 4. Select the "DVD-ROM Drive". 5. Now follow the instructions on the screen. Caution All existing data, such as programs, user settings, and authorizations will be deleted from the drives.
Servicing and maintenance 10.3 Installing software 10.3.4 Factory state without operating system The device can be optionally purchased without an operating system. If you want to install the operating system yourself, read the information available in the Internet at http://www.siemens.com/asis Notice You must integrate the required software components yourself if you install an operating system not offered by Siemens AG.
Servicing and maintenance 10.3 Installing software 10.3.5 Installing individual drivers Introduction The "Documentation and Drivers" CD contains the required drivers for the device. Procedure 1. Start "cdstart.exe" in the root directory of the CD. 2. Follow the instructions displayed on the screen. Note Further information on reinstalling the drivers is available on the Internet at "http://www2.automation.siemens.com/hmi" under "Support".
Servicing and maintenance 10.4 Maintenance and spare parts 10.4 10.4 Maintenance and spare parts The following spare parts are available for the device: Spare part Order No.
Servicing and maintenance 10.
11 Alarm, error and system messages 11.1 11.1 BIOS error messages Introduction This chapter contains a selection of alarms, error messages and troubleshooting information. Self-test POST During booting, the BIOS first performs a Power On Self-Test or POST. This checks to ensure that certain device components are functioning properly. The boot sequence is interrupted immediately if critical errors occur. If the POST does not find an error, the BIOS initializes and tests further components.
Alarm, error and system messages 11.2 Motherboard error messages 11.2 11.2 Motherboard error messages Error diagnosing The manual for the motherboard contains information about error messages originating from the motherboard. Note For information on error messages from the operating system or programs, refer to the corresponding manuals.
12 Troubleshooting and FAQs 12.1 12.1 General problems This chapter provides you with tips on how to localize and troubleshoot frequently occurring problems. Problem Possible cause Possible remedy The device is not operational There is no power supply to the device. • • • The external monitor remains dark. Check the power supply, the network cable and the mains connector. Check whether the On/Off switch is in the correct position. Press the soft power key. Check the ambient conditions.
Troubleshooting and FAQs 12.1 General problems Problem Possible cause Possible remedy Although the BIOS setting is OK, the time and data are still wrong. The back-up battery is dead. In this case, please contact your technical support team. USB device is not responding. The USB ports are disabled in the BIOS. Use a different USB port or enable the port. USB 2.0 device connected but USB 2.0 is disabled. Enable USB 2.0. Operating system does not support the USB interface.
Troubleshooting and FAQs 12.2 Problems when using modules of third-party manufacturers 12.2 12.2 Problems when using modules of third-party manufacturers Problem Possible cause The PC crashes during startup. • • • • • I/O addresses are assigned twice.
Troubleshooting and FAQs 12.3 SystemGuard errors 12.3 12.3 SystemGuard errors Notice SystemGuard is a freeware application for which Siemens AG offers no technical support. Observe the notes in the online help of the application. Hardware alarms The Silent Fan controller reports hardware alarms such as a fan failure. When a hardware alarm occurs, an information window opens for the affected object and displays an error message. You can reset the alarm.
13 Technical specifications 13.1 13.1.1 13.
Technical specifications 13.1 Technical data 13.1.
Technical specifications 13.1 Technical data Color display1) 12" TFT Key Noise emission 15" TFT Key 12" TFT Touch screen 15" TFT Touch screen 19" TFT Touch screen < 55 dB(A) according to DIN 45635-1 Motherboard Processor Chipset: Intel 865G - Intel® Pentium 4 2.4 GHz - Intel® Celeron 2.0 GHz Main memory 4 slots for 256 MB, 512 MB, 1GB, 2GB, 3GB 3GB max.
Technical specifications 13.1 Technical data Bad pixels Acceptable number Permanently bright and permanently dark pixels ≤ 12 Permanently bright, green pixels ≤5 Information concerning resistance to chemicals is located in the section "General information." 2) Additional mounting depth with DVD-ROM drive: + 28 mm = + 1.
Technical specifications 13.1 Technical data 13.1.3 Ambient and environmental conditions EMC Electromagnetic compatibility (EMC) EN 61000-6-4/EN 55022, EN 61000-6-2 / EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6 Mechanical conditions Tested according to Vibration load during operation 10 to 58 Hz: 0.0185 mm, 58 to 200 Hz: 0.25 g IEC 60068-2-6 Shock load during operation 1 g, 30 ms, 3 shocks IEC 60068-2-27 Temperature limits Operation Storage/transport 5° C ...
Technical specifications 13.2 Dimensional drawing of the device 13.2 Figure 13-1 13.2 Dimensional drawing of the device Dimensional drawing of the device Control units B H T 1) With key panel 12" TFT 15" TFT 483 483 310 355 147 172 With touch screen panel 12" TFT 15" TFT 19" TFT in mm 400 483 483 310 310 400 162 166 182 1) Additional device depth with CD-ROM drive: + 28 mm = + 1.
Technical specifications 13.3 Keyboard table 13.3 13.3 Keyboard table Key codes The following table applies only to control units with key panels. It contains all characters that can be entered in SIMATIC KeyTools in the "Key code table" area and under "User specific". The character that is triggered by pressing a specific key is listed in the "Display/function" column. Further information is available in the documentation for SIMATIC KeyTools on the "Documentation and Drivers" CD.
Technical specifications 13.
Technical specifications 13.
Technical specifications 13.
Technical specifications 13.3 Keyboard table Name Code (Hex) 0x Check-box Display/function =+ 2E — = L Shift/R Shift + R Alt × R Alt+L Shift/R Shift ÷ [{ ]} \| 2F 30 31 — [ L Shift/R Shift { R Alt « — ] L Shift/R Shift } R Alt » — \ L Shift/R Shift | R Alt ¬ R Alt+L Shift/R Shift ¦ Europe 1 32 — Europe 1 ;: 33 — ; L Shift/R Shift : R Alt ¶ R Alt+L Shift/R Shift ° ’" ‘~ ,< 34 35 36 .
Technical specifications 13.
Technical specifications 13.
Technical specifications 13.
Detailed descriptions 14.1 14.1 14 Overview of the Panel PC 577 motherboard The Panel PC 577 contains the Fujitsu-Siemens Premium Motherboard D1562-C. Further information is available in the manual for the motherboard on the "Documentation and Drivers" CD and in the Internet at "http://www.fujitsu-siemens.de".
Detailed descriptions 14.2 Riser card 14.2 14.2 Riser card Introduction A passive riser card is used as the bus board. With a passive riser card, the interrupts are fetched from the next slot on the motherboard via an adapter and cable. The cables are plugged into the riser card and the PCI adapter and are not soldered.
Detailed descriptions 14.3 Touch sensor 14.3 14.3 Touch sensor Principle of operation The touch device variant operates with an analog-resistive touch sensor. An electrical field is generated by electrodes along the edge of the sensor. These electrodes are arranged on a specific grid on the active surface.
Detailed descriptions 14.3 Touch sensor Effects of the scalloping effect Following the field lines at the edge of the display, the mouse pointer forms curves rather than straight lines. Figure 14-3 Effects of the scalloping effects on the mouse pointer The scalloping effect, therefore, can make it difficult or almost impossible to select icons on the edge of the display in Windows applications.
Detailed descriptions 14.4 System resources 14.4 14.4.1 14.4 System resources Currently allocated system resources The system resources (hardware address, memory configuration, IRQ, DMA channel) are assigned dynamically by the Windows OS, depending on the hardware configuration, drivers and externally connected peripheral devices. Dialogs show the current allocation of the system resources or existing conflicts.
Detailed descriptions 14.4 System resources 14.4.
Detailed descriptions 14.5 BIOS setup 14.5 14.5.1 14.5 BIOS setup Starting BIOS setup Starting BIOS setup Start the setup program as follows: Reset the device (warm or cold restart). In the figures shown, the default settings differ based on the device versions. With the default settings on the SIMATIC Panel PC 577, for example, the following screen appears after booting: Phoenix cME FirstBIOS Desktop Pro Copyright 1985–2004 Phoenix Technologies Ltd.
Detailed descriptions 14.5 BIOS setup 14.5.2 BIOS setup default settings Special default settings Panel PC 577 The default settings of the BIOS setup may reset in some circumstances, for example, when the back-up battery is exchanged or when the BIOS is updated. If your device has a BIOS version that is older than V5.00 R2.15, the BIOS setup default settings will not correspond to the default settings of the device. The differences are shown in the following table and must be entered manually.
A A Appendix A.1 A.1.1 A.1 Certificates and guidelines Guidelines and declarations Notes on the CE marking The following applies to the SIMATIC product described in this documentation: Notes for Norway, Sweden and Finland Caution Forsiktig Apparatet må tilkoples jordet stikkontakt. Varo Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
Appendix A.
Appendix A.1 Certificates and guidelines A.1.2 Certificates and approvals DIN ISO 9001 certificate The quality assurance system for the entire product process (development, production, and marketing) at Siemens fulfills the requirements of ISO 9001 (corresponds to EN29001: 1987). This has been certified by DQS (the German society for the certification of quality management systems). EQ-Net certificate no.: 1323-01 Software license agreement The device is shipped with software.
Appendix A.1 Certificates and guidelines EMC USA General This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interferences. 2. This device must accept any interference received, including interference that may cause undesired operation. Shielded cables The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices.
Appendix A.1 Certificates and guidelines A.1.3 ESD guideline What does ESD mean? Almost all electronic modules are equipped with highly integrated components and elements in MOS technology. For technological reasons, these electronic components are very sensitive to overvoltages and, consequently, to electrostatic discharge.
Appendix A.1 Certificates and guidelines Handling ESD modules As a rule: Only touch ESD components if unavoidable due to necessary tasks. Only touch the components when the following holds true: • You are permanently grounded by means of an ESD armband. • You are wearing ESD shoes or ESD shoes grounding protective strips in connection with ESD floors. Before you touch an electronic assembly, your body must be discharged. Touch a conductive object immediately beforehand, e.g.
Appendix A.1 Certificates and guidelines A.1.4 Electrostatic charging of individuals Anyone who is not connected to the electrical potential of their surroundings can be electrostatically charged. The figure below shows the maximum electrostatic voltages that can accumulate in a person who is operating equipment when he/she comes into contact with the materials indicated. These values comply with the specifications of IEC 801–2. Figure A-1 Electrostatic voltages with which an operator can be charged.
Appendix A.2 Abbreviations A.2 A-8 A.
Appendix A.3 Glossary Definitions CU A.3 A.3 Glossary Definitions CU Application An application is a program which is put directly on the operating system MS-DOS or windows. An application on the PC/PG, for example, is STEP 7. Programmable controller The programmable controllers of the SIMATIC S5 system consist of a central unit, one or several CPUs, and other modules, e.g. input modules and output modules.
Appendix A.3 Glossary Definitions CU Chipset Located on the motherboard, interconnects the processor with the RAM, the graphic controller, the PCI bus, and the external interfaces. COM interface The COM interface is a serial V.24 modem interface. The interface is suitable for asynchronous data transfer. As an alternative, connect printers with a serial interface. Controller Installed hardware and software which control the functions of specific internal or external devices, e.g. the keyboard controller.
Appendix A.3 Glossary Definitions CU Motherboard The motherboard, as the central part of the computer, processes and stores data, controls and manages interfaces and peripheral devices. Main memory The main memory represents the complete RAM area on a PC/PG. Hub A term from network technology. A device which joins communication lines at a central location and provides a common connection to all devices on the network. Image An image is, for example, an image of hard disk partitions.
Appendix A.3 Glossary Definitions CU Restore CD/DVD The Restore CD/DVD is used to restore the system partition or the entire hard disk to factory state if the system has crashed. The bootable CD/DVD contains all the necessary image files. They create a start diskette which restores the factory state through the network drive. ROM memory Read Only Memory The ROM memory is a read only memory in which every memory location can be addressed individually.
Index 1 C 12" variant, 8-3 15" variant, 8-9 Cable connector, 10-31 Cache, A-9 Calibrating, 7-5 Touch screen, 7-5 Canada, 5-10 CD-ROM drive, 8-11, 13-4 CD-RW, 13-3 Certificates, A-3 Certification, A-3 CheckLanguageID, 7-10 Checklist, 6-3 Chipset, A-10 Clamp, 4-1 Cleaning agents, 10-1 Cold restart, A-11 COM 1, 13-3 COM interface, A-10 COM port Interfaces, 2-4, 5-4 Commissioning, 1-6, 5-1, 5-3, 5-8, 6-3, 10-38 Device, 6-3 Compatibility of the Restore CD/DVD, 10-40 Components Additional, 6-8 Computer unit, 1
Index D Dash, 8-6 Data exchange, 9-1 Decimal point, 8-6 Declaration of conformity, A-2 Default settings, 14-8 Degree of protection, 3-9 IP54 degree of protection, 3-9 IP65 degree of protection, 3-9 Design, 2-2, 3-5 EMC compliant design, 3-5 Device, 2-2, 3-5, 4-1, 4-2, 5-8, 6-3, 7-1, 7-3, 10-1, 1030, 10-35 Commissioning, 6-3 Connecting, 5-8 EMC-compliant installation, 3-5 Installation, 4-1, 4-2, 10-35 Maintaining, 10-1 Separating, 10-30 Side view interface side, 2-2 Switching off, 7-3 Switching on, 7-1 USB
Index Hub, A-11 I Identification data, 3-4 Writing down, 3-4 Idle state, A-12 IEC, 13-2 IEC power connector, 5-5 Image, 10-40, A-11 Immunity to interference, 3-5 EMC compliant design, 3-5 EMC directive, 3-5 Information landscape, iv Installation, 3-5, 4-1, 4-2, 10-28, 10-35 Device, 4-1, 4-2, 10-35 Installing the device according to EMC directive, 3-5 Power supply, 10-28 Installation guidelines, A-2 Installation information, 3-6 installing, 10-44 Installing, 10-43 Drivers, 10-44 Operating system, 10-43 Inte
Index Mouse, 2-4, 5-3, 5-6, 13-2 External mouse, 5-3 Interfaces, 5-4 N Notation, iv Note, 1-4, 1-5, 3-6, 10-5 General information, 1-5 Installation instructions, 3-6 Safety information, 1-4, 10-5 O Offices, v On / Off switch, 8-1 Online ordering system, 9-1 Operating, 8-10 Touch screen, 8-10 Operating system, 2-3, 10-43 Installing, 10-43 Operator controls, 8-3, 8-9 For touch screen panel, 8-9 On the key panel, 8-3 P Package contents, 3-2 Checking, 3-2 Packaging, 3-2 Checking, 3-2 Removing, 3-2 Panel PC 5
Index Self-test, 6-6, 7-2, 11-1 Separating, 10-30 Device, 10-30 Serial interface, 2-4, 5-4 Service pack, 6-13 setting, 7-5 Setting Touch software, 7-5 Shipping, A-6 ESD, A-6 Shock load, 13-5 Sign, 8-6 Entering, 8-6 SIMATIC S7, 9-1 Integration, 9-1 slot, 2-3 Softkey, 8-5, 8-7 labeling, 8-7 Softkey row, 8-7 Software, 1-6, 10-41 Software components, 6-8 Additional software components, 6-8 Spare parts, 10-45 Special characters, 8-6 Entering, 8-6 Steel slot cover, 10-13, 10-14 Switching off, 7-3 Device, 7-3 Swit
Siemens AG Automation and Drives Industrial Automation Systems Postfach 4848 90437 NUERNBERG Federal Republic of Germany www.siemens.
