Preface SIMATIC HMI HMI devices MP 377, MP 377 PRO (WinCC flexible) SIMATIC HMI HMI devices MP 377, MP 377 PRO (WinCC flexible) Operating Instructions 1 Overview ______________ Safety instructions and approvals 2 ______________ 3 Planning application ______________ 4 Mounting and connecting ______________ Operator controls and displays 5 ______________ Configuring the operating system 6 ______________ 7 Commissioning a project ______________ 8 Operating a project ______________ 9 Operating alarms _____
Legal information Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
Preface Purpose of the operating instructions These operating instructions provide information based on the requirements defined by DIN EN 62079 for mechanical engineering documentation. This information relates to the place of use, transport, storage, mounting, use and maintenance. These operating instructions are intended for: ● Users ● Commissioning engineers ● Maintenance personnel Read especially the information in the section "Safety instructions" (Page 37).
Preface Position in the information landscape These operating instructions form part of the SIMATIC HMI documentation. You can obtain an overview of SIMATIC hardware and SIMATIC software products and SIMATIC systems and information that can be called up in PDF format in various languages at the following address: "http://www.automation.siemens.com/simatic/portal/html_76/techdoku.
Preface Representatives and office locations If you have any further questions relating to the products described in this manual, please contact your local representative at the Siemens branch nearest you. Locate your contact person at "http://www.automation.siemens.com/partner". Training center Siemens AG offers a variety of training courses in order to familiarize you with automation systems. Contact your regional Training Center or the central Training Center in D-90327 Nuremberg, Germany.
Preface 6 MP 377, MP 377 PRO (WinCC flexible) Operating Instructions, 10/2008, 6AV6691-1DR01-0AB0
Table of contents Preface ...................................................................................................................................................... 3 1 2 3 Overview.................................................................................................................................................. 13 1.1 Product overview .........................................................................................................................13 1.2 1.2.1 1.2.2 1.
Table of contents 4 5 6 8 Mounting and connecting......................................................................................................................... 53 4.1 Checking the package contents.................................................................................................. 53 4.2 4.2.1 4.2.2 Installing the HMI device ............................................................................................................. 54 Installing the MP 377 mounting device ..
Table of contents 7 6.7 Canceling password protection..................................................................................................113 6.8 6.8.1 6.8.2 6.8.3 6.8.4 6.8.5 6.8.6 6.8.7 6.8.8 6.8.9 6.8.10 6.8.11 6.8.12 Changing HMI device settings ...................................................................................................114 Setting the date and time ...........................................................................................................
Table of contents 8 10 7.6 7.6.1 7.6.2 7.6.3 Backup and restore ................................................................................................................... 168 Overview ................................................................................................................................... 168 Backup and restore using WinCC flexible................................................................................. 169 Backup and restore using ProSave .....................
Table of contents 9 10 8.11 8.11.1 8.11.2 8.11.3 Operating the Sm@rtClient view ...............................................................................................220 Overview ....................................................................................................................................220 Touch operation .........................................................................................................................221 Key control ...............................
Table of contents 10.9 Exporting a recipe data record.................................................................................................. 270 10.10 Examples .................................................................................................................................. 271 10.10.1 Entering a recipe data record.................................................................................................... 271 10.10.2 Manual production sequence...........................
1 Overview 1.1 Product overview The Multi Panel MP 377 HMI devices are an innovative advanced development of the 370 series. In addition to the established display sizes of 12", 15", and 19", the product series was expanded to include the Multi Panel MP 377 PRO 15" Touch offering all around IP65 degree of protection. The distinguishing feature of the HMI devices is that they fulfill the increasing demands for technical innovation – especially in regard to display, performance and extended applications.
Overview 1.1 Product overview IP65 all-round The Multi Panel MP 377 PRO, which features a housing with IP65 degree of protection, all around protection against dust and water jets. The ready-to-use HMI device can be fixed either from the top or the bottom to a support arm system or to a stand. A basic adapter and adapter sets that can be ordered separately support fixing systems from various manufacturers (including VESA standard for flat screens). The rear wall can be removed quite easily.
Overview 1.2 MP 377 mounting devices 1.2 MP 377 mounting devices 1.2.
Overview 1.
Overview 1.2 MP 377 mounting devices 1.2.
Overview 1.
Overview 1.2 MP 377 mounting devices 1.2.
Overview 1.
Overview 1.2 MP 377 mounting devices 1.2.
Overview 1.
Overview 1.3 MP 377 PRO 1.3 MP 377 PRO 1.3.
Overview 1.3 MP 377 PRO Rear view 1.3.2 ① Housing rear panel ② Lower cover Structure of the basic adapter ① Seal ② Cable channel ③ Mechanical interface to the MP 377 PRO ④ Mechanical interface to the adapter from the adapter set The basic adapter is included in the product package of the MP 377 PRO. An adapter set forms part of the basic adapter and can be ordered as an accessory.
Overview 1.4 Accessory kit 1.4 Accessory kit Accessory kit for MP 377 mounting device The accessory kit contains the following: ● Mains terminal for the power supply ● Mounting clamps for mounting the HMI device Additional documents may be enclosed with the accessory kit.
Overview 1.5 Accessories 1.5 Accessories Accessories are not included in the product package of the HMI device, but can ordered in the Internet at "http://mall.automation.siemens.com". RS 422 to RS 232 converter The converter is required for the connection of controllers of other manufacturers. Connect the RS 422 to RS 232 converter to the RS 422 / RS 485 interface. The converter converts the input signals to RS-232 signals. Order number for RS 422 to RS 232 converter: 6AV6 671-8XE00-0AX0.
Overview 1.5 Accessories Service packages The service packages include: ● Mounting seals ● Mounting clamps ● Power supply terminal, 2-pin Service packages can be ordered for the following HMI devices using the following order numbers: HMI device Order no. MP 377 12" Key 6AV6 574-1AA00-2BX0 MP 377 12" Touch 6AV6 671-4XA00-0AX0 MP 377 15" Touch MP 377 19" Touch Basic adapter One basic adapter is included in the delivery scope of the MP 377 PRO 15" Touch.
Overview 1.6 The HMI device in the operating process 1.6 The HMI device in the operating process The HMI device is part of the operating process. The following two phases are key to the way the HMI device is integrated in the operating process: ● Project design ● Process management Project design Visualization of the operating process is known as project design.
Overview 1.7 Functional scope with WinCC flexible 1.7 Functional scope with WinCC flexible The following tables show the objects that can be integrated in a project for an MP 377. Note The specified values are maximum values of the individual objects. Simultaneous use of multiple objects with their maximum value can lead to problems in the active project.
Overview 1.
Overview 1.7 Functional scope with WinCC flexible Safety Object Specification MP 377 User view Number of user groups 50 Number of users 50 Number of authorizations 32 Info texts Object Specification Info texts Length (no.
Overview 1.8 Software options 1.8 Software options The following software options are available for the MP 377: ● WinCC flexible /Sm@rtService The WinCC flexible /Sm@rtService option enables you to access a remote HMI device or PC via Ethernet. ● WinCC flexible /Sm@rtAccess The WinCC flexible /Sm@rtAccess option enables you to set up communication between different HMI systems.
Overview 1.9 Communication 1.9 Communication Number of connections Connection MP 377 Number using a bus connection 6 Number of connections based on "SIMATIC HMI HTTP Protocol" 8 NOTICE Communication faults with PROFINET IO When you release PROFINET IO in the HMI device's control panel, communication faults may arise in the following cases: • Use of PLCs from other manufacturers • Use of SIMATIC 500/505 via NITP Do not release PROFINET IO in the HMI device's control panel in the cases given.
Overview 1.9 Communication PLCs The following table shows the PLCs which can be used with the HMI devices and the protocols or profiles which can be used.
Overview 1.9 Communication PLC Protocol OMRON PLC series SYSMAC C, SYSMAC CV, SYSMAC CS1, SYSMAC alpha and CP • Hostlink/Multilink (SYSMAC Way)6) Yes Telemecanique PLC series TSX 7 with P47 411, TSX 7 with P47/67/87/107 420, TSX 7 with P47/67/87/107 425, module TSX SCM 21.6 with the specified TSX 7 CPUs, TSX 17 with module SCG 1161, TSX 37 (Micro) and TSX 57 (Premium) • Hostlink/Multilink (SYSMAC Way)6) Yes 1) Not possible when connected to S7-212.
Overview 1.
Safety instructions and approvals 2.1 2 Safety instructions High frequency radiation NOTICE Unwanted operating states High-frequency radiation, for example, from cellular phones, can trigger unwanted operating states. Proper use WARNING Commissioning the HMI device is prohibited until it has been absolutely ensured that the machine in which the HMI device is to be installed complies with Directive 98/37/EC or Directive 2006/42/EC as of December 29, 2009.
Safety instructions and approvals 2.1 Safety instructions Working on the control cabinet The following information applies to MP 377 mounting devices. WARNING Open equipment The HMI device is open equipment. This means that the HMI device may only be mounted in housings or cabinets, whereby the device can be operated from the front panel. The cubicle or cabinet in which the HMI device is installed may only be accessed with a key or tool and only by trained, authorized personnel.
Safety instructions and approvals 2.2 Standards, certificates and approvals 2.2 Standards, certificates and approvals Approvals CAUTION The following overview shows possible approvals. The HMI device itself is certified as shown on the rear panel labels.
Safety instructions and approvals 2.2 Standards, certificates and approvals UL approval Underwriters Laboratories Inc., to ● UL 508 (Industrial Control Equipment) ● CSA C22.2 No. 142 (Process Control Equipment) or Underwriters Laboratories Inc., to ● UL 508 (Industrial Control Equipment) ● CSA C22.2 No.
Safety instructions and approvals 2.3 Notes about usage 2.3 Notes about usage Industrial applications The HMI device is designed for industrial applications. It conforms to the following standards: ● Requirements for emissions EN 61000-6-4: 2007 ● Requirements for interference immunity EN 61000-6-2: 2005 Use in residential areas Note The HMI device is not intended for use in residential areas. Operation of an HMI device in residential areas can have a negative influence on radio/TV reception.
Safety instructions and approvals 2.4 Electromagnetic compatibility 2.4 Electromagnetic compatibility Introduction The HMI device fulfills, among other things, the requirements of the EMC law pertaining to the domestic European market. EMC-compatible installation of the HMI device The EMC-compliant installation of the HMI device and the application of interference-proof cable is the basis for interference-free operation.
Safety instructions and approvals 2.4 Electromagnetic compatibility Sinusoidal interference The following table shows the EMC behavior of the modules with respect to sinusoidal interference. This requires the HMI device to meet the specifications and directives for electrical installation.
Safety instructions and approvals 2.5 Transport and storage conditions 2.5 Transport and storage conditions Mechanical and climatic conditions for transportation and storage This HMI device meets the requirements for IEC 61131-2 relating to transport and storage conditions. The following specifications apply to the transport and storage of an HMI device in its original packaging.
3 Planning application 3.1 Notes about usage Mechanical and climatic conditions of use The HMI device is designed for use in a location protected from the effects of the weather.
Planning application 3.1 Notes about usage Testing mechanical ambient conditions The following table provides information on the type and scope of tests for mechanical ambient conditions. Tested for Test standard Comments Vibrations Vibration test in accordance with IEC 60068, part 2–6 (sinusoidal) Type of vibration: Transitional rate of the frequency: 1 octave/minute. 10 ≤ f ≤ 58, Constant amplitude 0.075 mm 58 ≤ f ≤ 150, constant acceleration 1 g, with support arm 0.
Planning application 3.2 MP 377 mounting devices 3.2 MP 377 mounting devices 3.2.1 Mounting positions and type of fixation Mounting position The HMI device is suitable for installation in: ● Mounting cabinets ● Control cabinets ● Switchboards ● Consoles In the following, all of these mounting options are referred to by the general term "cabinet". The HMI device is self-ventilated and approved for vertical and inclined mounting in stationary cabinets.
Planning application 3.2 MP 377 mounting devices Mounting Metal mounting clamps are provided for mounting. The mounting clamps hook into the oblong holes on the HMI device. 3.2.2 ① Threaded pin ② Hook Preparing for installation Select the mounting location of the HMI device Points to observe when selecting the mounting location: ● Position the HMI device so that it is not subjected to direct sunlight. ● Position the HMI device such that it is ergonomically accessible for the user.
Planning application 3.
Planning application 3.2 MP 377 mounting devices 3.2.3 Information on insulation tests, protection class and degree of protection Test voltages Insulation strength is demonstrated in the type test with the following test voltages in accordance with IEC 61131-2: Circuits with a nominal voltage of Ue to other circuits or ground Test voltage < 50 V 500 V DC Protection class Protection Class I in accordance with IEC 60536, i.e.
Planning application 3.3 MP 377 PRO 3.3 MP 377 PRO 3.3.1 Mounting positions Mounting position The HMI device is self-ventilated and approved for vertical and inclined mounting. – 3.3.2 + Mounting position Deviation from the vertical ① Inclined ≤ 35° ② Vertical 0° Preparing for installation Select the mounting location of the HMI device Points to observe when selecting the mounting location: ● Position the HMI device so that it is not subjected to direct sunlight.
Planning application 3.3 MP 377 PRO 3.3.3 Information on insulation tests, protection class and degree of protection Test voltages Insulation strength is demonstrated in the type test with the following test voltages in accordance with IEC 61131-2: Circuits with a nominal voltage of Ue to other circuits or ground Test voltage < 50 V 500 VDC Protection class Protection Class I in accordance with IEC 60536, i.e.
Mounting and connecting 4.1 4 Checking the package contents Check the package content for visible signs of transport damage and for completeness. NOTICE Damaged parts A damaged part will cause the HMI device to malfunction. Do not install parts damaged during shipment. In the case of damaged parts, contact your Siemens representative.
Mounting and connecting 4.2 Installing the HMI device 4.2 Installing the HMI device 4.2.1 Installing the MP 377 mounting device Requirement All packaging components and protective foils should be removed from the HMI device. To install the HMI device, you need the mounting clamps from the accessory kit. The mounting seal must be fitted on the HMI device. If the mounting seal is damaged, order a replacement seal. The mounting seal is part of the associated service pack.
Mounting and connecting 4.2 Installing the HMI device Positions of mounting clamps on the MP 377 12" Touch The following figure shows the counting direction for the insertion of the mounting clamps. The following table shows the positions of the mounting clamps on the MP 377 12" Touch. Observe the counting direction.
Mounting and connecting 4.2 Installing the HMI device Positioning the mounting clamps on the MP 377 15" Touch The following figure shows the counting direction for the insertion of the mounting clamps. The following table shows the positioning of the mounting clamps on the MP 377 15" Touch. Observe the counting direction.
Mounting and connecting 4.2 Installing the HMI device Procedure NOTICE Installation of the HMI device Always mount the HMI device according to the instructions in this manual. Risk of guaranteed level of protection not being met If the mounting seal is damaged or protrudes beyond the HMI device, the level of protection is not ensured. Check the fit of the mounting seal. Note Tighten the threaded pins of the mounting clamps until the HMI device is flush with the surface of the control cabinet.
Mounting and connecting 4.2 Installing the HMI device Result The HMI device is mounted and the relevant level of protection is ensured at the front. See also Accessory kit (Page 25) Accessories (Page 26) Information on insulation tests, protection class and degree of protection (Page 50) 4.2.2 Installing MP 377 PRO Requirement All packaging components and protective foils should be removed from the HMI device.
Mounting and connecting 4.2 Installing the HMI device Procedure This section describes how to install the device on a support arm system. Installation on a stand is carried out analogously. Proceed as follows: 1. Remove the 10 screws ⑥ of the housings rear panel using a size 2 Allen wrench. 2. Remove the rear panel of the housing ⑦ and store it in a secure location. 3.
Mounting and connecting 4.2 Installing the HMI device 6. Fasten the HMI device to the support arm ①. In doing so, ensure that all connections are fed (without damage) through the adapter into the inside of the HMI device. 7. If you want to connect the cables at a later point in time, fasten the housing rear panel ⑦ to the HMI device. Result The HMI device is fitted and can be connected electrically.
Mounting and connecting 4.3 Connecting the HMI device 4.3 Connecting the HMI device 4.3.1 Overview Requirement ● The HMI device must be mounted according to the specifications of these operating instructions. ● Always use shielded standard cables for the data cable. Additional information is available in the catalog and online order system at "http://mall.automation.siemens.com". Connection sequence Connect the HMI device in the following sequence: 1. Equipotential bonding 2.
Mounting and connecting 4.3 Connecting the HMI device 4.3.2 Ports The following figure shows the ports of the HMI device MP 377. ① Power supply connector ② RS-422/RS-485 port X10 / IF1b ③ PROFINET, 2 ports X1 P1 and X1 P2 ④ USB, ports X20 and X21 ⑤ Line in and micro ⑥ Line out Connect PROFIBUS DP or MPI to the X10 / IF1b port. You can affix the USB and PROFINET connecting cables to the rear panel of the HMI device with cable ties.
Mounting and connecting 4.3 Connecting the HMI device 4.3.3 Connecting the equipotential bonding circuit Differences in electrical potential Differences in electrical potential can develop between spatially separated plant components. Such electrical potential differences can lead to high equalizing currents over the data cables and therefore to the destruction of their interfaces. Equalizing currents can develop if the cable shielding is terminated at both ends and grounded to different plant parts.
Mounting and connecting 4.3 Connecting the HMI device Wiring diagram ① Chassis terminal on the HMI device, example ② Equipotential bonding conductor cross-section: 4 mm2 ③ Control cabinet ④ Equipotential bonding conductor cross-section: min.
Mounting and connecting 4.3 Connecting the HMI device 4.3.4 Connecting the power supply Wiring diagram The following figure shows the connection between the power supply and HMI device. 03 ಯ 7RXFK 03 ಯ .H\ 03 ಯ 7RXFK 03 ಯ 7RXFK 03 352 ಯ 7RXFK Note when connecting The mains terminal for connecting the power supply is contained in the accessory kit. The mains terminal is designed for cables with a maximum cross-section of 1.5 mm².
Mounting and connecting 4.3 Connecting the HMI device Connecting the mains terminal NOTICE Damage Do not tighten the screws of the power supply terminal if it is plugged into the HMI device. The pressure from the screwdriver may otherwise damage the HMI device socket. Only connect the wires when the mains terminal is withdrawn. *1' 9'& Connect the power supply terminal to the cables of the power supply as shown in the figure above.
Mounting and connecting 4.3 Connecting the HMI device 4.3.5 Connecting an uninterruptible power supply Connection graphic The following figure shows the connection between the uninterruptible power supply and HMI device. The uninterruptible power supply is connected to the 24-V input and one of the HMI device's USB ports. When connected to the HMI device's USB port, the following uninterruptible power supplies are supported: SITOP DC UPS modules as of a rated power value of 6 A, e.g.
Mounting and connecting 4.3 Connecting the HMI device 4.3.6 Connecting the PLC Wiring diagram The following figure shows the connection between the PLC and HMI device. 6,0$7,& 6 3/& 6,0$7,& 6 6,0$7,& 6 6,0$7,& 6,0$7,& 3/& 352),1(7 352),1(7 (WKHUQHW /$1 56 56 56 56 56 56 3/& 56 56 3/& 56 56 03 ಯ 7RXFK 3/& RI RWKHU PDQXIDFWXUHU 03 ಯ .
Mounting and connecting 4.3 Connecting the HMI device NOTICE Approved cable If you do not use approved cables to connect a SIMATIC S7 controller, you may experience malfunctions. Only use approved cables to connect a SIMATIC S7 controller. Standard cables are available for the connection. You can find additional information on this in the Internet at "http://mall.automation.siemens.com".
Mounting and connecting 4.3 Connecting the HMI device Configuring an RS-422/RS-485 port A DIP switch S1 for the configuration of the RS-422/RS-485 port is located on the rear of the HMI device. In the factory state, the DIP switch is set for communication with the SIMATIC S7 PLC via RS 485. Note Note the diagrams of DIP switch settings on the rear panel of the HMI device. The following table shows the DIP switch settings. The send and receive direction is toggled internally using the RTS signal.
Mounting and connecting 4.3 Connecting the HMI device 4.3.7 Connecting the configuration PC Wiring diagram The following figure shows the connection between the configuring PC and HMI device. 86% 352),1(7 56 56 56 03 ಯ 7RXFK 03 ಯ .H\ 03 ಯ 7RXFK 03 ಯ 7RXFK 03 352 ಯ 7RXFK The ports are described in the specifications. For the RS-485 to RS-232 conversion, you can order the PC/PPI cable from Siemens AG using order number 6ES7 901-3CB30-0XA0.
Mounting and connecting 4.3 Connecting the HMI device Configuring the PC/PPI cable Use the DIP switches to configure the transfer rate of the PC/PPI cable. Note Set a lower bit rate if the connection is lost during the operating system update. If you use a higher bit rate, you must use the PC/PPI cable version 3 or higher. The version code is printed on the cable ("E stand 3," for example, corresponds to version 3).
Mounting and connecting 4.3 Connecting the HMI device Note when connecting NOTICE USB connection sequence Observe the following sequence when connecting by USB: 1. HMI device 2. PC USB host-to-host cable Use only the driver for the USB host-to-host cable that is included in the WinCC flexible package. Never use the driver supplied with the USB host-to-host cable.
Mounting and connecting 4.3 Connecting the HMI device 4.3.8 Connecting a USB device Below are examples of devices you can connect to the USB port of the HMI device: ● External mouse ● External keyboard ● Printer ● USB memory stick ● Industrial USB Hub 4 Industrial USB hub 4 can be obtained using order number 6AV6671-3AH00-0AX0.
Mounting and connecting 4.3 Connecting the HMI device 4.3.9 Connecting a printer Wiring diagram The following figure shows the connection between the printer and HMI device. 86% 352),1(7 03 ಯ 7RXFK 03 ಯ .
Mounting and connecting 4.3 Connecting the HMI device Note when connecting NOTICE Data exchange cables If you use cables without a metallic netting shield between the HMI device and printer, you may experience functional problems. Only use cables with metal-braided shielding grounded at both ends for connecting the HMI device and printer. Note Some printers may require the ASCII character set used in the project to also be defined on the printer.
Mounting and connecting 4.4 Switching on and testing the HMI device 4.4 Switching on and testing the HMI device Procedure Proceed as follows: 1. Switching on the power supply. The screen lights up after power is switched on. A progress bar is displayed during startup. If the HMI device fails to start, you have probably crossed the wires on the mains terminal. Check the connected wires and change their connection. The Loader opens after the operating system has started.
Mounting and connecting 4.4 Switching on and testing the HMI device Result The Loader appears again. Note When restarting the system, a project may already be loaded on the HMI device. The project will then start after an adjustable delay or when you press the "Start" button. Use the relevant operating element to close the project. Refer to your plant documentation to find any additional information on this topic. Function test Perform a function test following commissioning.
Mounting and connecting 4.5 Securing the cables 4.5 Securing the cables 4.5.1 Securing cables on the MP 377 mounting device After the power-on test, to ensure strain relief, use cable ties to secure the connected cables to the marked fixing elements. )DVWHQLQJ HOHPHQW 4.5.2 Securing cables on the MP 377 PRO After the power-on test, use cable ties to secure the connected cables to the marked clasps to ensure strain relief.
Mounting and connecting 4.6 Closing the housing rear wall of MP 377 PRO 4.6 Closing the housing rear wall of MP 377 PRO Requirement ● All cables are connected. Procedure Proceed as follows: 1. Check that the seal is properly seated on the housing. NOTICE IP65 degree of protection at risk If the seal on the rear wall of the housing is damaged, the IP65 degree of protection is at risk. This is a repair case. Proceed as described in the section Spare parts and repairs (Page 274). 2.
5 Operator controls and displays 5.1 Front operator controls MP 377 Touch ① Display with touch screen The MP 377 Touch is operated via the touch screen. All operating elements required for operator input are displayed on the touch screen once the HMI device has started. NOTICE Unintentional action possible Do not carry out several operations simultaneously. You may otherwise trigger an unintentional action.
Operator controls and displays 5.1 Front operator controls MP 377 12" Key ① Function keys with LED ② System keys - alphanumeric keys ③ Display ④ System keys – control keys ⑤ System keys - cursor keys The MP 377 12" Key is operated using the system keys and the function keys. The function assigned to a specific function key is defined during configuration. The function keys have no function prior to the project being opened.
Operator controls and displays 5.2 Inserting a memory card 5.2 Inserting a memory card Introduction The following can be saved to the memory card of the HMI device: ● Backup of the HMI device ● Logs ● Recipes ● Operating system ● Applications ● Other data such as video files, Word, Excel or PDF files The memory card can be inserted during operation. Note The multimedia card of the SIMATIC S7 PLC cannot be used. Procedure Proceed as follows: 1. Insert the memory card into the relevant slot.
Operator controls and displays 5.3 Securing memory card 5.3 Securing memory card Introduction The HMI device is designed for the tough conditions experienced in industry. Therefore use the locking bracket to secure the memory card in its slot. Requirements A memory card has been inserted. Procedure Proceed as follows: 1. Loosely screw in the Torx screw ①. 2. Place the locking bracket ② against the memory card. 3. Tighten the Torx screw ①. Result The memory card is secure.
Operator controls and displays 5.4 Unplugging the memory card 5.4 Unplugging the memory card Introduction The memory card can be unplugged during operation. Do not remove the memory card while data is being accessed by an application, e.g. during backup or recipe transfer. Procedure NOTICE Loss of data possible The data on the memory card is lost if you attempt to remove it while the HMI device is accessing its data. Do not remove the memory card while data is being accessed.
Operator controls and displays 5.5 Labeling the function keys on the MP 377 12" Key 5.5 Labeling the function keys on the MP 377 12" Key Introduction You can label the function keys as required for your project. Use the labeling strips for this purpose. Preprinted key labeling strips may be ordered as accessories, see section Accessories (Page 26). Note Do not write on the keyboard to label the function keys. Printing labeling strips WinCC flexible comes with a range of labeling strip templates.
Operator controls and displays 5.5 Labeling the function keys on the MP 377 12" Key Procedure Proceed as follows: 1. Edit and then print the template. You can also print blank templates and label them manually. 2. Apply a fixing spray film to the labeling strips. The fixing spray ensures that the text is water resistant and does not smear, and that the printer ink on the keyboard membrane does not run. 3. Cut out the labeling strip.
Operator controls and displays 5.
Configuring the operating system 6.1 6 Loader Overview The following figure shows the Loader. The header line contains details of the loader version. These details are not shown in the following figure. The Loader buttons have the following functions: ● Press the "Transfer" button to set the HMI device to "Transfer" mode. The transfer mode can only be activated when at least one data channel has been enabled for the transfer. ● Press the "Start" button to start the project on the HMI device.
Configuring the operating system 6.1 Loader The following figure shows the open start menu. Depending on the software installed, other symbols may be displayed in the desktop's status bar. Open Loader The following options are available to open the Loader: ● The Loader appears briefly after starting the HMI device. ● The Loader appears when the project is closed. If configured, use the relevant operating element to close the project. For further information on this, refer to your plant documentation.
Configuring the operating system 6.1 Loader Key operation in the Windows CE interface The following table shows the key combinations for navigating in the user interface. Key combination CTRL + ESC ALT + ESC ALT + TAB Function The taskbar is activated with the open Windows CE start menu. The next active program is displayed. The Task Manager is opened. Key operation in the Explorer The following table shows the key combinations for navigating in the Explorer.
Configuring the operating system 6.1 Loader Protection against unauthorized use You can protect the control panel against unauthorized access by using a password. You can also protect the taskbar and the Desktop with the help of SecureMode. If the HMI device is protected, "secure mode" is displayed on the Windows CE desktop. You can find additional information on this in the section "Setting up and disabling SecureMode (Page 94)".
Configuring the operating system 6.1 Loader Note Internet Explorer for Windows CE and the Internet Explorer version which can run on a PC differ in terms of functionality. Internet Explorer for Windows CE has separate proxy settings that are independent of the settings in the control panel of the HMI device. You can find additional information at the Microsoft Website. Media Player Media Player for Windows CE is installed on the HMI device.
Configuring the operating system 6.2 Setting up and disabling SecureMode 6.2 Setting up and disabling SecureMode Overview You can protect the control panel against unauthorized access with a password. You can also protect the taskbar and the Desktop with the help of the SecureMode. Function of SecureMode You set up SecureMode by setting up a password in the control panel. SecureMode is then automatically activated. The label "secure mode" is displayed in the Windows CE Desktop.
Configuring the operating system 6.3 Viewer 6.3 Viewer Introduction You can use ProSave to install viewers for various data formats. You can tell which viewers are installed by a symbol on the desktop and from the Start menu under "Programs".
Configuring the operating system 6.4 Control Panel 6.4 Control Panel 6.4.1 Overview The HMI device's Control Panel is similar to the control panel on a PC.
Configuring the operating system 6.4 Control Panel 6.4.2 Opening the Control Panel Introduction The HMI device Control Panel can be opened as follows: ● Independently of a running project – Press the "Control panel" button in the loader. – By calling up from the Windows CE start menu. ● With active project An operating element must be configured to open the control panel for this purpose. Procedure – open the Control Panel via the Start menu Proceed as follows: 1. Open the Windows CE start menu.
Configuring the operating system 6.4 Control Panel 6.4.3 Reference for functions Overview of functions The following table shows the settings in the Control Panel.
Configuring the operating system 6.
Configuring the operating system 6.4 Control Panel Entries using an external keyboard An external keyboard can be used to operate the Control Panel in exactly the same way as the HMI device keyboard. Use the keys of the external keyboard which correspond to the HMI device keys in the description. Operator entries using an external mouse An external mouse can be used to operate the Control Panel in exactly the same way as the HMI device touch screen. Click the described operating elements with the mouse.
Configuring the operating system 6.4 Control Panel Input with the screen keyboard A screen keyboard is available for data input. The screen keyboard is displayed as soon as you touch a text box. You can also call up the screen keyboard directly from the Control Panel. Display methods for the screen keyboard You can change the display method for the screen keyboard and fix the position on the screen. Confirm the entry with the button or abort the entry with the key.
Configuring the operating system 6.4 Control Panel Changing the display of the screen keyboard Key Functions Switching between the numerical and alphanumerical keyboard Switching between the normal level and Shift level of the alphanumerical screen keyboard Switchover to special characters Switching from full display to reduced display Switching from reduced display to full display Close the screen keyboard 6.4.4.
Configuring the operating system 6.4 Control Panel 8. Make the necessary changes. To do this, highlight the corresponding input object using the TAB key. – Use the system keys of the HMI device to enter the new values in the text boxes. – To operate a button, select the button with the cursor keys and then press – Open the drop down list boxes with the key combination + ALT ENTER . . Select the required entry from the drop down list box using the cursor keys.
Configuring the operating system 6.4 Control Panel Control keys The following tables show the control keys used to select and operate the control panel. ● Select operating elements Key TAB SHIFT + Functions Description Tabulator Selects the next/previous operating element in the tab sequence. Cursor keys Selects the next operating element to the left, right, above or below the current screen object. TAB Navigates in the operating element.
Configuring the operating system 6.4 Control Panel Enter key combinations Key A-Z Functions Purpose Toggle key assignment Toggles the assignment for a key with multiple assignment. • No LED is lit • The number assignment is enabled. Pressing the button once toggles to letter assignment. An LED is lit The left or right letter assignment is enabled. Each time the key is pressed, the system toggles between the left letter assignment, the right letter assignment and the number assignment.
Configuring the operating system 6.5 Changing settings for operation 6.5 Changing settings for operation 6.5.1 Configuring the screen keyboard Introduction The details provided below will explain how the screen keyboard can be displayed and positioned. Requirements You have opened the "Siemens HMI Input Panel - Options" dialog with icon.
Configuring the operating system 6.5 Changing settings for operation 5. If you want to change the position of the screen keyboard, use the mouse pointer to select a free space between the keys. Release the mouse pointer when the required position has been reached. 6. If you want to increase or decrease the size of the keyboard screen, place your mouse pointer over the button . 7. Adapt the screen keyboard size by dragging it to size with the mouse pointer. 8.
Configuring the operating system 6.5 Changing settings for operation Procedure Proceed as follows: 1. If you want to enable character repetition, activate the "Enable character repeat" check box. 2. If you want to change the delay, press a button or the slider in the "Repeat delay" group. Moving the slider to the right will shorten the delay. Moving to the left will extend the delay. 3. If you want to change the repeat rate, press a button or the slider in the "Repeat rate" group.
Configuring the operating system 6.5 Changing settings for operation Requirements You have opened the "Mouse Properties" dialog with the "Mouse" icon. ① Pattern ② Icon Procedure Proceed as follows: 1. Click the pattern twice. After the second click, the colors of the pattern will be reversed and the white fields will change to gray. The time before the second click is saved. 2. Check the double-click. Click on the icon twice in succession to do this.
Configuring the operating system 6.5 Changing settings for operation 6.5.4 Calibrating the touch screen Introduction Depending on the mounting position and viewing angle, it is possible that parallax may occur when operating the touch screen. In order to prevent any operating errors as a result, calibrate the touch screen again in the startup phase or during runtime. Requirements You have opened the "OP Properties" dialog "Touch" tab with the "OP" icon. Procedure Proceed as follows: 1.
Configuring the operating system 6.5 Changing settings for operation 3. Briefly touch the middle of the calibration crosshairs for each position. Once you have touched all the positions of the calibration crosshairs, the following dialog appears: New calibration settings have been measured. Tape the screen to register saved data. Wait for 30 seconds to cancel saved data and keep the current setting. Time limit: 30 sec 4. Touch the touch screen. The calibration is saved.
Configuring the operating system 6.6 Setting up password protection 6.6 Setting up password protection Introduction You can protect access to the Control Panel and the Windows CE taskbar with a password. Requirements You have opened the "Password Properties" dialog with the "Password" icon. NOTICE Password not available If the password is no longer available, you will have to wait for the operating system to be updated again.
Configuring the operating system 6.7 Canceling password protection 6.7 Canceling password protection Requirements You have opened the "Password Properties" dialog with the "Password" icon. Procedure Proceed as follows: 1. Delete the entries in the "Password" and "Confirm password" text boxes. 2. Confirm your entries. The dialog closes. Result Password protection for the Control Panel and Windows CE taskbar is canceled and they can be freely accessed.
Configuring the operating system 6.8 Changing HMI device settings 6.8 Changing HMI device settings 6.8.1 Setting the date and time Introduction You can set the date and time on the HMI device. The HMI must be restarted in the following cases: ● You have changed the time zone setting ● You have changed the "Daylight savings time currently in effect" check box setting. Requirements You have opened the "Date/Time Properties" dialog with the "Date/Time Properties" icon.
Configuring the operating system 6.8 Changing HMI device settings 5. Confirm your input by clicking on the "Apply" button. The values you have set are now in effect. Note The system does not automatically switch between winter and summer time. 6. If you want to switch from winter to summer time, activate the "Daylight savings time currently in effect" check box. When you press the "Apply" button, the time is brought forward by one hour. 7.
Configuring the operating system 6.8 Changing HMI device settings Requirements You have opened the "Regional and Language Settings" dialog with the "Regional Settings" icon. ① Region selection box Procedure Proceed as follows: 1. Select the region from the selection box. 2. Change to the "Number", "Currency", "Time" and "Date" tabs and set the selection boxes to the desired settings. 3. Confirm your entries. The dialog closes. Result The HMI device's regional settings have been changed. 6.8.
Configuring the operating system 6.8 Changing HMI device settings Requirements You have opened the "OP Properties" dialog, "Persistant Storage" tab with the "OP" icon. ① Significance of the text: Saves the current registry information to the flash memory. The HMI device loads the saved registry information the next time it boots.
Configuring the operating system 6.8 Changing HMI device settings 6.8.4 Changing monitor settings Requirements You have opened the "OP Properties", dialog "Display" tab with the "OP" icon. Procedure Proceed as follows: 1. If you want to increase the brightness, press the "UP" button. 2. If you want to decrease the brightness, press the "DOWN" button. 3. Confirm your entries. The dialog closes. Result The screen settings have been changed.
Configuring the operating system 6.8 Changing HMI device settings 6.8.5 Setting the screen saver Introduction You can set the following time intervals on the HMI device: ● For the automatic activation of the screen saver ● For the automatic reduction in the screen's backlighting When you do not undertake an operation within the configured interval, the configured function will be activated automatically.
Configuring the operating system 6.8 Changing HMI device settings Requirement You have opened the "Screensaver" dialog with the "ScreenSaver" icon. ① Time interval in minutes until backlighting is reduced ② Period of time in minutes before the screen saver is activated ③ Radio buttons for the screensaver Procedure Proceed as follows: 1. Enter the interval in minutes after which the backlighting is to be reduced. Entering "0" will deactivate the backlighting reduction. 2.
Configuring the operating system 6.8 Changing HMI device settings Requirement You have opened the "Printer Properties" dialog with the "Printer" icon. ① Selection box for the printer ② Interface selection box ③ Network address of the printer ④ Paper format selection box ⑤ Group orientation with radio buttons for print orientation ⑥ Print quality check box ⑦ Color printing check box Procedure Proceed as follows: 1. Select a printer from the "Printer Language" selection box.
Configuring the operating system 6.8 Changing HMI device settings 6.8.7 Enabling sound and setting sound volume Introduction You can activate an acoustic feedback for keyboard and touch screen operations. With each touch or activation of a key, a sound is emitted. Requirements You have opened the "Volume & Sounds Properties" dialog, "Volume" tab with the "Volume & Sounds" icon.
Configuring the operating system 6.8 Changing HMI device settings Procedure Proceed as follows: 1. Activate the check boxes needed in the "Enable sounds for" group. If no check boxes are activated, no acoustic feedback will be output. 2. If you want signaling for entries to be audible, activate the following check box: – With key control: "Hardware buttons". – With touch control: "Screen taps". 3. Use the "Loud" and "Soft" radio buttons to select between loud and quiet signaling. 4.
Configuring the operating system 6.8 Changing HMI device settings 6.8.8 Assigning sound to an event Introduction When acoustic feedback is activated, a sound is used to report an event. You can select the sound to reflect the event. Requirements ● A loudspeaker is connected to the HMI device. ● You have opened the "Volume & Sounds Properties", dialog "Sound" tab with the "Volume & Sounds" icon. Procedure Proceed as follows: 1. Select a suitable sound from the "Event" group.
Configuring the operating system 6.8 Changing HMI device settings 6.8.9 Restarting the HMI device Introduction You can restart the HMI device or reset the factory settings before rebooting. Further information on this can be found in the section "Resetting factory settings (Page 174)". Required restart The HMI device must be restarted in the following cases: ● You have activated or deactivated the PROFINET IO direct keys. ● You have changed the time zone setting.
Configuring the operating system 6.8 Changing HMI device settings Procedure 1. If you want to restart the HMI device, press the "Reboot" button. The following message is displayed: ① If you run this function, all data which has not been backed up will be lost. Please close all applications before restarting. ② Button for reset to factory settings and subsequent restart ③ Button for restart 2. Press one of the buttons. ● If you want to restart the HMI device, press the "Reboot" button.
Configuring the operating system 6.8 Changing HMI device settings 6.8.10 Displaying information about the HMI device Introduction You will need the device-specific information if you contact Technical Support. Requirement You have opened the "OP Properties" dialog box, "Device" tab, by touching the "OP" icon. The following figure applies to the MP 377 15" Touch. The data displayed are device-specific and may therefore deviate from that of your HMI device.
Configuring the operating system 6.8 Changing HMI device settings 6.8.11 Displaying system properties Introduction The general system-specific information provides you with information about the processor, operating system and memory. Requirements You have opened the "System Properties", dialog "General" tab with the "System" icon. The data displayed are device-specific and may therefore deviate from that of your HMI device.
Configuring the operating system 6.8 Changing HMI device settings 6.8.12 Displaying memory distribution Introduction The "Memory" system-specific information provides you with information about the distribution and size of the memory in the HMI device. NOTICE "Memory" tab Do not change the memory distribution in the "Memory" tab. Applies for the usage of options: An alteration to the memory distribution may be necessary. Please refer to the accompanying documentation for further information.
Configuring the operating system 6.9 Setting storage location 6.9 Setting storage location Introduction There are various storage locations available for storing the compressed source file of your project. The following describes how you can set the storage location. Requirements You have opened the "Transfer Settings", dialog "Directories" tab with the "Transfer" icon.
Configuring the operating system 6.10 Setting the delay time 6.10 Setting the delay time Introduction Once the HMI device has been switched on, a project can be started after a delay. The Loader is displayed during the delay time. Requirements You have opened the "Transfer Settings", dialog "Directories" tab with the "Transfer" icon.
Configuring the operating system 6.11 Setting the uninterruptible power supply 6.11 Setting the uninterruptible power supply Introduction UPS monitoring is an option you load as an add-on with ProSave. A UPS ensures that the HMI device is shut down in a controlled manner after a buffer time in the event of a power failure. This avoids the loss of data. The following uninterruptible power supplies are supported: SITOP DC UPS modules as of a rated power value of 6 A, e.g.
Configuring the operating system 6.12 State of uninterruptible power supply Result Port monitoring for the UPS is set. See also State of uninterruptible power supply (Page 133) 6.12 State of uninterruptible power supply Introduction If you have connected a UPS to a USB port, you can display the monitoring state of this port. Requirements You have opened the "UPS Properties", dialog "Current status" tab with the "UPS" icon. ① The "UPS program is not running. No current status available.
Configuring the operating system 6.13 Enabling PROFINET IO 6.13 Enabling PROFINET IO PROFINET IO If the HMI device is connected to the PLC via PROFINET, function keys or buttons, for example, can be configured as PROFINET IO direct keys. If PROFINET IO direct keys are used in the project, they must be enabled. Note If you enable PROFINET IO direct keys, you cannot use the RS 422/RS 485 port for serial communication. PROFINET IO direct keys and PROFIBUS DP direct keys are mutually exclusive.
Configuring the operating system 6.13 Enabling PROFINET IO Within the ETHERNET data network, the device name must be unique and satisfy the DNS conventions. These include: ● Restriction to 127 characters in total (letters, digits, hyphen or point) ● A name component within the device name, e.g. a string between two points, may not exceed 63 characters. ● Special characters such as umlauts, brackets, underscores, slashes, spaces etc. are not permitted. The hyphen is the one exception.
Configuring the operating system 6.14 Changing transfer settings 6.14 Changing transfer settings 6.14.1 Configuring the data channel Introduction If you block all data channels, the HMI device is protected against unintentional overwriting of the project data and HMI device image. Note A project can only be transferred from the configuring PC to the HMI device when at least one of the data channels is enabled on the HMI device.
Configuring the operating system 6.14 Changing transfer settings NOTICE "Remote control" for "Channel 1" If the "Remote Control" check box is activated during "Online" operating mode, the X10 port cannot be used for communication. The "Remote Control" check box must be deactivated for "Online" operating mode. Once the serial transfer is complete, in the "Channel 1" group you must therefore deactivate the "Remote Control" check box.
Configuring the operating system 6.14 Changing transfer settings Procedure Proceed as follows: 1. If you want to enable a data channel, activate the "Enable Channel" check box in the "Channel 1" or "Channel 2" group. In the "Channel 1" group, the RS-422/RS-485 port is enabled for the serial data transfer. The network port is enabled in the "Channel 2" group. 2. If you want to enable the automatic transfer, activate the associated "Remote Control" check box. 3.
Configuring the operating system 6.14 Changing transfer settings 6.14.2 Changing MPI/PROFIBUS DP settings Introduction The communication settings for MPI or PROFIBUS DP are defined in the HMI device project.
Configuring the operating system 6.14 Changing transfer settings Procedure Proceed as follows: 1. Select a network. 2. Use the "Properties" button to open the "MPI" or "PROFIBUS" dialog. ① The HMI device is the only master on the bus. ② Bus address of the HMI device ③ Time-out ④ Data transmission rate in total network ⑤ Highest station address in the network ⑥ Profile ⑦ Button for displaying the bus parameters 3.
Configuring the operating system 6.14 Changing transfer settings 8. If you want to view the profile data, press the "Busparameter" button of the PROFIBUS dialog. The profile data are displayed. The "Profile" dialog is read-only. NOTICE The bus parameters must be the same for all stations in the MPI/PROFIBUS DP network. 9. Close the "Profile" dialog. 10. Confirm your entries. The dialog closes. Result The MPI/PROFIBUS DP settings of the HMI device have been changed.
Configuring the operating system 6.15 Configuring network operation 6.15 Configuring network operation 6.15.1 Overview of network operation Introduction You can connect the HMI device to a PROFINET network via the Ethernet port. NOTICE The HMI device only has client functionality in the PC network. This means that users can access files of a node with TCP/IP server functionality from the HMI device via the network.
Configuring the operating system 6.15 Configuring network operation Printing via a network printer The HMI device's operating system does not support line by line alarm logging via a network printer. All other printing functions, for example, hardcopy or logs, are available without restriction via the network. Preparation Before beginning the configuration, request the following network parameters from your network administrator.
Configuring the operating system 6.15 Configuring network operation 6.15.2 Setting the device name of the HMI device Introduction The HMI device uses the device name to identify itself in the communication network. Requirements You have opened the "System Properties", dialog "Device Name" tab with the "System" icon. ① Device name of the HMI device ② Description for the HMI device (optional) Note To activate the network functions, enter a unique computer name in the "Device name" text box.
Configuring the operating system 6.15 Configuring network operation 6.15.3 Changing the network configuration Introduction You can change the network settings for the LAN connection under "Network&Dial-Up Connections". Requirements You have opened the following display using the "Network&Dial-Up Connections" MP 377, MP 377 PRO (WinCC flexible) Operating Instructions, 10/2008, 6AV6691-1DR01-0AB0 icon.
Configuring the operating system 6.15 Configuring network operation Procedure Proceed as follows: 1. Open the "ERTEC400" entry. The "'ERTEC400 Ethernet Driver' Settings" dialog is opened. 2. If you need automatic issuing of addresses, select the "Obtain an IP address via DHCP" radio button. 3. If you need manual issuing of addresses, select the "Specify an IP address" radio button. 4.
Configuring the operating system 6.15 Configuring network operation 6.15.4 Changing the logon data Introduction Windows CE uses this information to gain access to the network resources. Enter the user name, password and domain you have received from your administrator. Requirements You have opened the "Network ID" dialog with the "Network ID" icon. Procedure Proceed as follows: 1. Enter the user name in the "User name" text box. 2. Enter your password in the "Password" text box. 3.
Configuring the operating system 6.15 Configuring network operation 6.15.5 Changing e-mail settings Requirements You have opened the "WinCC flexible Internet Settings" dialog with the "WinCC Internet Settings" icon. ① Setting the SMTP server ② Name for the sender ③ E-mail account Note Additional tabs may appear in the "WinCC flexible Internet Settings" dialog. This depends on the options that have been enabled for network operation in the project. Procedure Proceed as follows: 1.
Configuring the operating system 6.15 Configuring network operation 6.15.6 Changing Internet settings 6.15.6.1 Changing general Internet settings Requirements You have opened the "Internet Options", dialog "General" tab with the "Internet Options" icon. Note Do not change the settings in the "User Agent" field. Procedure Proceed as follows: 1. Enter the homepage for the Internet browser in the "Start Page" text box. 2. Enter the address of the required search engine in the "Search Page" text box. 3.
Configuring the operating system 6.15 Configuring network operation 6.15.6.2 Setting the proxy server Requirements You have opened the "Internet Options", dialog "Connection" tab with the "Internet Options" icon. Procedure Proceed as follows: 1. Select the "Use LAN (no autodial)" check box. 2. If you are using a proxy server, in the "Network" group, activate the "Access the Internet using a proxy server" check box. Specify the address of the proxy server and the port. 3.
Configuring the operating system 6.15 Configuring network operation Requirements You have opened the "Internet Options" dialog, "Privacy" tab with the "Internet Options" icon. Procedure Proceed as follows: 1. Select the required cookie behavior by means of the radio buttons. – "Accept" Cookies are stored without request. – "Block" Cookies will not be stored. – "Prompt" Cookies will be stored on request. 2.
Configuring the operating system 6.15 Configuring network operation 6.15.6.4 Importing and deleting certificates Overview You can import, view and delete certificates that have been imported for the HMI device. The certificates differ in the following ways: ● Certificates that you trust ● Own certificates ● Other certificates You can import additional certificates and delete certificates that are not required. The required settings can be obtained from your network administrator.
Configuring the operating system 6.16 Saving to external storage device (backup) 6.16 Saving to external storage device (backup) Introduction A backup involves copying the operating system, applications and data from the internal in flash memory of the HMI device to an external storage device. The following external storage devices are possible: ● External memory ● USB memory stick Requirements ● The HMI device features an external storage device with sufficient free space.
Configuring the operating system 6.16 Saving to external storage device (backup) Procedure Proceed as follows: 1. Press the "BACKUP" button to open the "Select Storage Card" dialog. The "--- no storage card available ---" message appears if there is no external memory in the HMI device or if this memory is defective. Insert an external memory or a different one. 2. Select the external memory for backup from the "Please select a Storage Card" list box. 3. Click on the "Start Backup" button.
Configuring the operating system 6.17 Restoring from external storage device 6.17 Restoring from external storage device Introduction A restore operation deletes the old data from flash memory of the HMI device on confirmation. The data stored on the external memory is then copied to the internal flash Flash memory. Requirements ● The external memory holding the backed up data is inserted in the HMI device. ● You have opened the "Backup/Restore" dialog with the "Backup/Restore" icon.
Configuring the operating system 6.17 Restoring from external storage device Procedure Proceed as follows: 1. Press the "RESTORE" button to open the "Storage Card" dialog. ① No storage card available ② Only one storage card containing backup is allowed. No storage card detected. Insert a storage card and press the "Refresh" button. 2. Select the external memory with the backup from the "Storage Card with Backup detected" selection box.
Configuring the operating system 6.17 Restoring from external storage device 5. The data to be restored is checked. The following messages are displayed in sequence during the check. – "Starting Restore" – "Checking data" When the data has been checked, the following message is displayed: "You are starting RESTORE now. All files (except files on storage cards) and the registry will be erased. Are you sure?" The message means that the restore process can be started.
Configuring the operating system 6.18 Activate memory management 6.18 Activate memory management Memory management Provided the memory management is activated, the HMI device will automatically close the project if the memory needs reorganizing during an active project. The project is shut down and the HMI device will display a message. You have to restart the project. NOTICE Memory management If you do not activate memory management, undefined states can occur during the runtime of the project.
Commissioning a project 7.1 7 Overview Configuration phase A project – the process image of the working process – is produced during configuration to visualize automated working processes. The process displays for the project contain displays for values and messages which provide information about process statuses. The process control phase follows the configuration phase. Process control phase The project must be transferred to the HMI device if it is to be used in process control.
Commissioning a project 7.2 Operating modes 7.2 Operating modes Operating modes The HMI device may be in the following operating modes: ● Offline ● Online ● Transfer "Offline mode" and "Online mode" can be set on both the configuring PC and the HMI device. To set these modes on the HMI device, use a corresponding operating element of the project.
Commissioning a project 7.3 Using existing projects 7.3 Using existing projects The following table shows how you can reuse existing projects, while observing the screen size: HMI device in the existing project New HMI device MP 370 12" Touch MP 377 12" Touch MP 370 12" Key MP 377 12" Key MP 370 15" Touch MP 377 15" Touch, MP 377 PRO 15" Touch The following cases are possible: 1. Project exists in ProTool Migrate the project to WinCC flexible and then replace the HMI device. 2.
Commissioning a project 7.4 Data transmission options 7.4 Data transmission options Overview The following table shows the options for data transfer between the MP 377 and the configuring PC.
Commissioning a project 7.5 Transfer 7.5 Transfer 7.5.1 Overview Transfer Transfer the executable project from the configuring PC to the HMI device. You can start the "Transfer" mode manually or automatically on the HMI device. Transferred data is written directly to the internal flash memory on the HMI device. For the transfer, you use a data channel which you have to configure before starting a transfer.
Commissioning a project 7.5 Transfer Requirements ● The project "*.hmi" is opened in WinCC flexible. ● The HMI device is connected to a configuring PC. ● The data channel is configured on the HMI device. ● The HMI device is in "Transfer" mode. Procedure Proceed as follows: 1. On the configuring PC, select the "Transfer settings" command in the menu "Project > Transfer" in WinCC flexible. The "Select devices for transfer" dialog opens. 2. Select the HMI device in the left area of the dialog. 3.
Commissioning a project 7.5 Transfer NOTICE If the automatic transfer has been activated on the HMI device and a transfer is initiated on the configuring PC, the project currently running is automatically stopped. The HMI device then automatically switches to "Transfer" mode. After the commissioning phase, deactivate the automatic transfer so that the HMI device cannot be inadvertently switched to transfer mode. The transfer mode can trigger unintentional actions in the device.
Commissioning a project 7.5 Transfer 7.5.4 Starting backtransfer Requirements ● No project is open in WinCC flexible. ● The HMI device is connected to a configuring PC. ● The data channel is configured on the HMI device. ● The HMI device is in "Transfer" mode. ● The memory card containing the compressed project file is inserted into the HMI device. Procedure Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible.
Commissioning a project 7.5 Transfer 7.5.5 Testing a project Introduction There are two options to test a project: ● Test the project on the configuring PC You can test a project at a configuring PC, using a simulator. For detailed information, refer to the "WinCC flexible" user manual and to the WinCC flexible Online Help. ● Offline testing of the project on the HMI device Offline testing means that communication between the HMI device and PLC is down while the test is being carried out.
Commissioning a project 7.6 Backup and restore Procedure In "Online" mode, you can test individual project functions on the HMI device without them being affected by the PLC. PLC tags are updated in this case. You have the option to test all communication-dependent functions, for example alarms, etc. Test the operating elements and views of the project. 7.6 Backup and restore 7.6.
Commissioning a project 7.6 Backup and restore 7.6.2 Backup and restore using WinCC flexible Requirements ● No project is open on the configuring PC in WinCC flexible. ● The HMI device is connected to this configuring PC. ● The data channel is configured on the HMI device. Procedure for backup Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication Settings" dialog opens. 2.
Commissioning a project 7.6 Backup and restore Procedure for restore Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication Settings" dialog opens. 2. Select the type of HMI device. 3. Select the type of connection between the HMI device and the configuring PC. 4. Set the connection parameters. 5. Close the dialog with "OK". 6.
Commissioning a project 7.6 Backup and restore 7.6.3 Backup and restore using ProSave Requirements ● The HMI device is connected to a PC on which ProSave is installed. ● The data channel is configured on the HMI device. Procedure for backup Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. Set the connection parameters. 4.
Commissioning a project 7.6 Backup and restore Procedure for restore Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. 4. Set the connection parameters. 5. Select the "*.psb" backup file to be restored from the "Restore" tab. You can see the HMI device for which the backup file was created and the type of backup data the file contains. 6.
Commissioning a project 7.7 Updating the operating system 7.7 Updating the operating system 7.7.1 Overview Updating the operating system A compatibility conflict may occur when transferring a project to the HMI device. This is caused by different versions of the configuration software used and the HMI device image available on the HMI device. If there are different versions, the transfer is aborted. A message indicating a compatibility conflict is displayed on the configuration PC.
Commissioning a project 7.7 Updating the operating system 7.7.2 Resetting factory settings In ProSave or WinCC flexible, you can update the operating system with or without resetting to factory settings. ● Updating the operating system without resetting to factory settings First, switch into "Transfer" mode on the HMI device or use the automatic transfer function if the project is active. Then start the operating system update in ProSave or WinCC flexible.
Commissioning a project 7.7 Updating the operating system 7.7.3 Updating the operating system using WinCC flexible Requirements ● No project is open on the configuring PC in WinCC flexible. ● The HMI device is connected to this configuring PC. ● The data channel is configured on the HMI device. Procedure Proceed as follows: 1. On the configuring PC, select the "Communication settings" command from the "Projekt > Transfer" menu in WinCC flexible. The "Communication Settings" dialog opens. 2.
Commissioning a project 7.7 Updating the operating system 7.7.4 Updating the operating system using ProSave Requirements ● The HMI device is connected to a PC on which ProSave is installed. ● The data channel is configured on the HMI device. Procedure Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. 4. Set the connection parameters. 5.
Commissioning a project 7.7 Updating the operating system 7.7.5 Resetting to factory settings with WinCC flexible Requirements ● No project is open on the configuring PC in WinCC flexible. ● The HMI device is connected to this configuration PC over the standard Ethernet cable. ● Have the MAC address of the Ethernet interface on your HMI device to hand. – The MAC address is displayed briefly when the HMI device is turned on. – The MAC address is displayed in the "PROFINET" dialog in the Control Panel.
Commissioning a project 7.7 Updating the operating system Procedure - Restoring factory settings Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication Settings" dialog opens. 2. Select the HMI device type from the "General" tab, and select "Ethernet" from the "Connection" area. 3. Enter an IP address.
Commissioning a project 7.7 Updating the operating system 9. In WinCC flexible, select "Update OS" on the configuring PC to run the operating system update. 10. In the Control Panel of the HMI device, open the "OP Properties" dialog and select the "Device" tab. 11. Click on the "Reboot" button. A query is opened. 12. Click on the "Prepare for Reset" button. 13. On the configuration PC, follow the instructions in WinCC flexible. During the operating system update a status view opens to indicate progress.
Commissioning a project 7.7 Updating the operating system 7.7.6 Resetting to factory settings with ProSave Requirement ● The HMI device is connected over the Ethernet to a PC on which ProSave is installed. ● Have the MAC address of the Ethernet interface on your HMI device to hand. – The MAC address is displayed briefly when the HMI device is turned on. – The MAC address is displayed in the "PROFINET" dialog in the Control Panel. Procedure - Setting the PC interface 1.
Commissioning a project 7.7 Updating the operating system 4. Change to the "OS Update" tab. 5. Activate the "Reset to factory settings" check box. A text box opens where you can enter the MAC address. 6. Enter the HMI device's MAC address in the text box. 7. In "Image path", select the HMI device image file "*.img". The HMI device image files are available under "WinCC flexible Images" in the WinCC flexible installation folder or on the WinCC flexible installation CD.
Commissioning a project 7.8 Installing and removing options Result A message is displayed when the operating system update is successfully completed. This operation has deleted the project data from the HMI device. The factory settings are reset. Note If you can no longer call the Control Panel on the HMI device, as the operating system is missing, switch off the HMI device. Then reset to factory settings and restart the HMI device. If the HMI device doesn´t start up, switch it off and then on again.
Commissioning a project 7.8 Installing and removing options 7.8.2 Installing and removing options using WinCC flexible Requirements ● No project is open on the configuring PC in WinCC flexible. ● The HMI device is connected to this configuring PC. ● The data channel is configured on the HMI device. Procedure for installing an option Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible.
Commissioning a project 7.8 Installing and removing options Procedure for removing an option Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication Settings" dialog opens. 2. Select the type of HMI device. 3. Select the type of connection between the HMI device and the configuring PC, then set the connection parameters. 4. Close the dialog with "OK". 5.
Commissioning a project 7.8 Installing and removing options 7.8.3 Installing and removing options using ProSave Requirements ● The HMI device is connected to a PC on which ProSave is installed. ● The data channel is configured on the HMI device. Procedure for installing an option Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3.
Commissioning a project 7.9 Transferring and transferring back license keys Procedure for removing an option Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC, then set the connection parameters. 4. Select the "Options" tab. 5. Press the "Device status" button to update the display. 6. Select the desired option under "Installed options". 7.
Commissioning a project 7.9 Transferring and transferring back license keys 7.9.2 Transferring and transferring back license keys Requirements ● When transferring or transferring back using WinCC flexible: No project is open on the configuring PC in WinCC flexible. ● The HMI device is connected to this configuring PC. ● The data channel is configured on the HMI device. ● The storage location and the license key awaiting transfer are ready. Procedure for transferring a license key Proceed as follows: 1.
Commissioning a project 7.9 Transferring and transferring back license keys Procedure for transferring a license key back Proceed as follows: 1. Switch to "Transfer" mode on the HMI device. 2. When transferring back using WinCC flexible: Select the "License Keys" command in the menu "Project > Transfer". The Automation License Manager opens. When transferring back using the Automation License Manager: Start the Automation License Manager via the Windows Start menu. 3.
Operating a project 8.1 8 Overview Configuration and process control phase HMI devices can be used to operate and monitor tasks in process and production automation. The plant screens on the HMI devices are used to provide a clear overview of the active processes. The HMI device project, which includes the plant screens, is created during the configuration phase.
Operating a project 8.1 Overview Operating a project with an external keyboard An external keyboard can be used to operate a project in exactly the same way as with the HMI keyboard or screen keyboard. Note The function keys of the external keyboard are disabled. Use the other keys of the external keyboard, which correspond to the HMI device keys in the description.
Operating a project 8.1 Overview Optical feedback from operating elements The operating element receives the focus and is selected. The configuration engineer can also configure the selection of an operating element so that it deviates from the standard. Further information on this may be available in your plant documentation.
Operating a project 8.2 Direct keys 8.2 Direct keys Introduction Direct keys on the HMI device are used to set bits in the I/O area of a SIMATIC S7. Direct keys enable operations with short reaction times that are, for example, a jog mode requirement. NOTICE Direct keys are still active when the HMI device is in "offline" mode. NOTICE If you operate a function key with direct key functionality in a running project, the direct key function is always executed, independent of the current screen contents.
Operating a project 8.3 Setting the project language 8.3 Setting the project language Introduction The HMI device supports multilingual projects. You must have configured a corresponding operating element which lets you change the language setting on the HMI device during runtime. The project always starts with the language set in the previous session. Requirements ● The required language for the project must be available on the HMI device.
Operating a project 8.4 Entries using the touch screen General procedure The operating elements of a screen are operated by touching the touch screen. Proceed as follows: 1. Touch the desired operating element within the screen. 2. Depending on the operating element, perform further actions. Detailed descriptions can be found under the respective operating element.
Operating a project 8.4 Entries using the touch screen 8.4.2 Entering and editing numerical values Numerical screen keyboard When you touch an operating element for numerical input on the HMI-device touch screen, the numerical screen keyboard appears. This is the case, for example, for a text box. The screen keyboard is automatically hidden again when input is complete. Note Opened screen keyboard PLC job 51 "Select screen" has no effect while the screen keyboard is open.
Operating a project 8.4 Entries using the touch screen Procedure Numerical values can be entered character-by-character via the buttons on the numerical screen keyboard. Proceed as follows: 1. Touch the desired operator control on the screen. The numerical screen keyboard opens. The existing value is displayed in the screen keyboard and is selected. 2. Enter the value. The keys with for example the letters G to Z are available to enter a hexadecimal value; however, the characters are not entered.
Operating a project 8.4 Entries using the touch screen 8.4.3 Entering and editing alphanumerical values Alphanumerical screen keyboard When you touch an operating element for alphanumerical input on the HMI-device touch screen, the alphanumerical screen keyboard appears. This is the case, for example, for a text box. The screen keyboard is automatically hidden again when input is complete. Note Opened screen keyboard PLC job 51 "Select screen" has no effect while the screen keyboard is open.
Operating a project 8.4 Entries using the touch screen Procedure Alphanumerical values can be entered character-by-character via the buttons on the alphanumerical screen keyboard. Proceed as follows: 1. Touch the desired operator control on the screen. The alphanumerical screen keyboard opens. The existing value is displayed in the screen keyboard and is selected. 2. Enter the value. You have the following options to enter a value: – The selected value is deleted when you enter the first character.
Operating a project 8.4 Entries using the touch screen 8.4.4 Entering the date and time Entering the date and time Enter the date and time in the same way you enter alphanumerical values. Note When entering the date and time, please note that the format is determined by the configured project language. 8.4.5 Entering symbolic values Drop down list Operating elements for entering symbolic values offer you a list from which you can select the input values.
Operating a project 8.4 Entries using the touch screen 8.4.6 Displaying infotext Purpose The configuration engineer uses infotext to provide additional information and operating instructions. The configuration engineer can configure infotext on screens and operating elements. The infotext of an I/O field may contain, for example, information on the value to be entered. Opening infotext for operating elements 1. Touch the required operating element. The screen keyboard opens.
Operating a project 8.5 Entries using the keys 8.5 Entries using the keys 8.5.1 Control keys Introduction The following tables show the control keys with which you operate the project. You will also find detailed descriptions under the individual operating elements. Select operating elements Key TAB SHIFT + Functions Description Tabulator Selects the next/previous operating element in the tab sequence.
Operating a project 8.5 Entries using the keys Key Functions Description ENTER Enter key • • • • Operates buttons. Accepts and ends an entry. Opens a drop down list box. Toggles within a text box between character mode and normal mode. In character mode, a single character is selected. In this mode, you can advance in the character set using the cursor keys. Cancel ESC • • INS DEL ALT + CTRL + ENTER Deletes the characters of a value entry and restores the original value.
Operating a project 8.5 Entries using the keys Acknowledge alarms Key ACK Functions Description Acknowledge Acknowledges the currently displayed fault alarm or all the alarms of an alarm group as group acknowledgment. The LED lights up as long as unacknowledged fault alarms are active. Displaying infotext Key HELP Functions Description Displaying infotext Opens a window with the configured infotext at the selected object, for example alarm or I/O field.
Operating a project 8.5 Entries using the keys 8.5.2 Example: enter characters using the alphanumeric keyboard Using the same keys of the alphanumeric keyboard you can enter up to six different characters. The entry result depends on the combination of the keys pressed. The values "5", "M", "m", "N", "n" and "%" are entered using the same key the keyboard. You can use the keys A-Z , SHIFT and FN M % N 5 of to switch between the different assignments.
Operating a project 8.5 Entries using the keys 8.5.4 General procedures Introduction The control keys and function keys of the HMI device are available for key control General procedure The operating elements of a screen are operated using the control keys of the HMI device. Proceed as follows: 1. Continue to press the key TAB or the cursor keys until the required operating element is selected on the screen. 2. Depending on the operating element, perform further actions.
Operating a project 8.5 Entries using the keys Procedure Numerical and alphanumerical values can be entered in character mode using the system keys. Proceed as follows: 1. Select the desired text box within the screen with TAB . The existing value is selected in the text box. 2. Enter the value using the numerical keypad. You have the following options to enter a value: – The existing value is deleted when you enter the first character. Completely reenter the value.
Operating a project 8.5 Entries using the keys 8.5.6 Entering and editing alphanumerical values Procedure Alphanumerical values can be entered in character mode using the system keys. Proceed as follows: 1. Select the desired text box within the screen with TAB . The existing value is selected in the text box. 2. Enter the value using the system keys. You have the following options to enter a value: – The existing value is deleted when you enter the first character. Completely reenter the value.
Operating a project 8.5 Entries using the keys 8.5.7 Entering the date and time Entering the date and time Enter the date and time in the same way you enter alphanumerical values. Note When entering the date and time, please note that the format is determined by the configured project language. 8.5.8 Entering symbolic values Drop down list When you select a symbolic I/O field, a drop down list opens. Procedure Symbolic values are selected from the entries of a drop down list. Proceed as follows: 1.
Operating a project 8.5 Entries using the keys 8.5.9 Displaying infotext Purpose The configuration engineer uses infotext to provide additional information and operating instructions. The configuration engineer can configure infotext on screens and operating elements. The infotext of an I/O field may contain, for example, information on the value to be entered. If the LED of the key HELP lights up, an infotext has been configured for the selected display object or for the current screen.
Operating a project 8.6 Bar and gauge 8.6 Bar and gauge Bar The bar is a dynamic display object. The bar displays a value from the PLC as a rectangular area. The bar allows you to recognize the following at a glance: ● The distance of the current value from the configured limit values ● Whether a set point value has been reached The bar can display values such as fill levels or batch counts.
Operating a project 8.7 Operating the switch 8.7 Operating the switch Introduction The switch is an operating element and display object with two predefined switching states, for example "On" and "Off". Switches can signalize the state of a plant section, for example if a motor is running or not. At the same time, you can use the switch to change the state of the corresponding plant section via the HMI device, for example from "On" to "Off".
Operating a project 8.8 Operating the trend view 8.8 Operating the trend view Trends Trends continuously display the current process data or process data from a log. Trend view Trends are displayed in the trend view. A trend view can display several trends simultaneously.
Operating a project 8.8 Operating the trend view Value table The trend values can be read from the value table if this is configured: ● When the ruler is displayed, the trend values are shown at a position of the ruler in the value table ● When the ruler is hidden, the latest trend values are displayed in the value table Ruler When configured, a ruler is available to provide an exact reading of the trend values in the value table. You can move the ruler to the desired position of the trend view.
Operating a project 8.9 Operating the slider control Touch operation Touch the required button in the trend view. The position of the ruler can also be changed by means of touching and dragging the ruler on the touch screen. Procedure using the keys Proceed as follows: 1. Using the key TAB select the desired button within the trend view. 2. Confirm your entry by pressing the key 8.9 ENTER .
Operating a project 8.9 Operating the slider control Procedure using the touch screen Proceed as follows: 1. Touch the slider of the desired slider control. 2. Move the slider to the required value. If a value display has been configured, you can check the exact value that has been set. 3. Release the slider.
Operating a project 8.10 Operating the Status Force 8.10 Operating the Status Force 8.10.1 Overview Application You read or write access values of the connected PLC directly with Status Force. Status Force allows you to monitor or change addresses of the PLC program, etc. You don't need to connect an additional programming device or additional PC to the PLC. Note Status Force can only be used in combination with SIMATIC S5 or SIMATIC S7. Layout The layout of Status Force depends on the configuration.
Operating a project 8.10 Operating the Status Force Operating elements Depending on your configuration, you can operate the Status Force using the following buttons: Buttons Functions "Read" button Updates the display in the "Status Value" column. This button engages when it is pressed. You cannot operate any text boxes until the button is actuated again and the refresh is stopped. "Write" button Applies the new value in the "Control Value" column. The control value is written to the PLC. 8.10.
Operating a project 8.10 Operating the Status Force Procedure for reading the status value Proceed as follows: 1. Enter the address and the desired format of a value for each line. Touch the respective columns to display the screen keyboard. 2. Once you have entered all of the desired values, touch the button. Result All values are read cyclically by the PLC and entered in the "Status Value" column until the button is touched again.
Operating a project 8.10 Operating the Status Force Key control The following table lists the key combinations for operating the Status Force: Keys Functions { CTRL + CTRL + CTRL + CTRL + CTRL + CTRL + CTRL + Operates the "Read" button. } Operates the "Write" button. ENTER Selects the first/last field in the current line. Selects the first/last field in the current column. Deletes the current line. INS DEL Otherwise: Do not select a PLC in the "Connection" column.
Operating a project 8.11 Operating the Sm@rtClient view Requirements for forcing The following requirements must be fulfilled in order to force values: ● The "Control Value" column must be available ● The "Write" button must be available Procedure for forcing a value Proceed as follows: 1. Enter the address of a value for each line. Enter the desired control value in the "Control Value" column. Select the respective fields and enter the values using the keyboard. 2.
Operating a project 8.11 Operating the Sm@rtClient view Monitoring mode On a Sm@rtClient view which is configured for monitoring mode, you can only monitor the remote HMI device. You cannot control its operation. Operation Note It is not possible to operate the direct keys of the remote HMI device from the local HMI device.
Operating a project 8.11 Operating the Sm@rtClient view Procedure for starting remote operation Proceed as follows: 1. On the HMI device change to the screen with the Sm@rtClient view. The following options are available for establishing the connection to the remote HMI device: – The connection is established automatically. – The connection must be established by touching the appropriate button.
Operating a project 8.11 Operating the Sm@rtClient view 8.11.3 Key control Operator input options The Sm@rtClient view can be operated as follows: ● Starting remote control ● Forcing permission ● Ending remote control Procedure for starting remote operation Proceed as follows: 1. On the HMI device change to the screen with the Sm@rtClient view. The following options are available for establishing the connection to the remote HMI device: – The connection is established automatically.
Operating a project 8.12 Project security Procedure for ending remote control You can end monitoring or control of a remote HMI device with one of the following methods depending on the configuration: ● Press the key configured for this ● Exit the screen containing the Sm@rtClient view ● If configured, display a menu with with ALT SHIFT + CTRL . Select the desired menu command and the respective identification letter. Further information on this may be available in your plant documentation. 8.
Operating a project 8.12 Project security Users and passwords Each user is assigned to exactly one user group. The following people are allowed to create users and assign them passwords: ● The configuration engineer during configuration ● The administrator on the HMI device ● A user with user management authorization on the HMI device Irrespective of the user group, each user is allowed to change his own password. Logoff times A logoff time is specified in the system for each user.
Operating a project 8.12 Project security 8.12.2 User view Application The user view is used to display the users on the HMI device: ● All users on the HMI device are displayed in the user view to the administrator or to a user with administrator authorizations ● If you are a user without user management authorization, you can only see your personal user entry The authorizations of a user after logging on depends on the user group to which the user is assigned.
Operating a project 8.12 Project security 8.12.3 User logon Logon dialog Use the logon dialog to log on to the security system of the HMI device. Enter your user name and password in the logon dialog.
Operating a project 8.12 Project security Procedure using the keys Proceed as follows: 1. Using the key TAB select the "User" text box within the logon dialog. 2. Enter the user name using the system keys. To enter letters, switch the numerical keypad to letter assignment using the key 3. Using the key TAB A-Z . select the "Password" text box. 4. Enter the password using the system keys. 5. Touch the "OK" button to confirm your entries. Note The user name is not case-sensitive.
Operating a project 8.12 Project security 8.12.5 Creating users 8.12.5.1 Creating users with touch operation Requirements You have opened a screen containing the user view. You have user management authorization or you are the administrator. NOTICE The following characters cannot be used in passwords: • Blank • Special characters * ? . % / \ ' " Procedure for creating a user in the simple user view Proceed as follows: 1. Touch the "" entry in the user view. The following dialog opens: 2.
Operating a project 8.12 Project security 6. Touch the text box "Logoff time". The screen keyboard is displayed. 7. Enter a value between 0 and 60 for the logoff time in minutes. The value 0 stands for "no automatic logoff." 8. Touch the "OK" button to confirm your entries. Procedure for creating a user in the enhanced user view Proceed as follows: 1. Touch the desired field in the blank line of the user view. The appropriate screen keyboard is displayed. 2. Switch into input mode by means of the key. 3.
Operating a project 8.12 Project security Procedure for creating a user in the simple user view Proceed as follows: 1. Select the user view using the key TAB or using the cursor keys. 2. Select the entry "" in the user view with the cursor keys and confirm with ENTER . The following dialog opens: 3. Enter the desired user name using the system keys. 4. Select the next text box with the TAB key and enter a password using the system keys. 5. Touch the "OK" button to confirm your entries.
Operating a project 8.12 Project security Procedure for creating a user in the enhanced user view Proceed as follows: 1. Select the user view with the 2. Select a blank line with the TAB key via the configured tab order. or keys. 3. Select the desired field in the blank line of the user view with the 4. Confirm your entry by pressing the key ENTER or keys. . 5. Enter the desired user data: – Enter the data using the system keyboard.
Operating a project 8.12 Project security 8.12.6 Changing user data 8.12.6.1 Changing user data with touch operation Requirements You have opened a screen containing the user view. Which data you are allowed to change depends on your authorization: ● You are an administrator or a user with user management authorization.
Operating a project 8.12 Project security 8.12.6.2 Changing user data with key operation Requirements You have opened a screen containing the user view. Which data you are allowed to change depends on your authorization: ● You are an administrator or a user with user management authorization. In these cases you are allowed to change the data for all the users on the HMI device in the user view: – User name – Group assignment – Password – Logoff time ● You are a user without user management authorization.
Operating a project 8.12 Project security 8.12.7 Deleting users Requirements You have opened a screen containing the user view. To delete a user, you must be an administrator or have user management authorization. Note The "Admin" and "PLC_User" users exist by default. These users cannot be deleted. Procedure To delete a user, delete the user name entered. Result The user has been deleted and may no longer log onto the project.
Operating a project 8.13 Closing the project 8.13 Closing the project Procedure Proceed as follows: 1. Use the corresponding operating element object to close the project. Wait for the Loader to open after you closed the project. 2. Switch off power to the HMI device.
Operating alarms 9.1 9 Overview Alarms Alarms indicate events and states on the HMI device which have occurred in the system, in the process or on the HMI device itself. A status is reported when it is received. An alarm could trigger one of the following alarm events: ● Incoming ● Outgoing ● Acknowledge The configuration engineer defines which alarms must be acknowledged by the user.
Operating alarms 9.1 Overview Alarm classes Alarms are assigned to various alarm classes: ● Error Alarms in this class must always be acknowledged.
Operating alarms 9.2 Detecting queued alarms 9.2 Detecting queued alarms Introduction You can recognize the presence of alarms which must be acknowledged by the following: ● For an HMI device with keys: The LED in the key ACK lights up. ● Depending on the configuration: An alarm indicator is displayed on screen. The configuration determines whether an alarm has to be acknowledged or not. This is also defined by the alarm class which an alarm belongs to.
Operating alarms 9.3 Message display 9.3 Message display Displaying alarms Alarms are displayed in the alarm view or in the alarm window on the HMI device. Alarm view Depending on the configuration, the alarm view is displayed as follows: ● As a single line. Alarm numbers and alarm texts are displayed as single lines ● As simple alarm view ● As enhanced alarm view In the simple or enhanced alarm views the configuration engineer specifies the alarm information to be displayed.
Operating alarms 9.3 Message display The buttons have the following functions: Buttons Functions Displaying infotext for an alarm. Process alarm. Acknowledging alarms. Changing the column sequence and sorting in the enhanced alarm view Depending on the configuration, you can change the column sequence and sorting order on HMI devices with touch operation.
Operating alarms 9.4 Displaying infotexts 9.4 Displaying infotexts Displaying infotext The configuration engineer can also provide infotext for alarms. Procedure using the touch screen Proceed as follows: 1. Touch the desired alarm in the alarm view or the alarm window. The alarm is selected. button in the simple alarm view or 2. Touch the in the enhanced alarm view. If configured, the infotext assigned to this alarm is displayed. 3.
Operating alarms 9.5 Acknowledge alarm 9.5 Acknowledge alarm Requirements The alarm to be acknowledged is displayed in the alarm window or the alarm view. Procedure using the touch screen Proceed as follows: 1. Touch the desired alarm in the alarm view or the alarm window. The alarm is selected. button in the simple alarm view or 2. Touch the in the enhanced alarm view.
Operating alarms 9.6 Editing alarms 9.6 Editing alarms Introduction The configuration engineer can assign additional functions to each alarm. These functions are executed when the alarm is processed. Note When you edit an unacknowledged alarm, it is acknowledged automatically. Requirements The alarm to be edited is displayed in the alarm window or the alarm view. Procedure using the touch screen Proceed as follows: 1. Touch the desired alarm in the alarm view or the alarm window. The alarm is selected.
Operating recipes 10.1 10 Overview Introduction Recipes are used when different variants of a product are manufactured with the same process. In this case, the product variants differ in terms of their type and quantity of the components, but not in terms of the manufacturing process sequence. The configuration engineer can store the combination of each individual product variant in a recipe.
Operating recipes 10.2 Structure of a recipe 10.2 Structure of a recipe Recipes The recipe collection for the production of a product family can be compared to a file cabinet. A recipe which is used to manufacture a product corresponds to a drawer in a file cabinet. Example: In a plant for producing fruit juice, recipes are required for different flavors. There is a recipe, for example, for the flavors orange, grape, apple and cherry.
Operating recipes 10.2 Structure of a recipe Recipe data records The drawers of the file cabinet are filled with suspension folders. The suspension folders in the drawers represent records required for manufacturing various product variants. Example: Product variants of the flavor apple might be a soft drink, a juice or nectar, for example.
Operating recipes 10.3 Recipes in the project 10.3 Recipes in the project Overview If recipes are used in a project, the following components interact: ● Recipe view / recipe screen On the HMI device, recipes are displayed and edited in the recipe view or in a recipe screen. – The recipe data records from the internal memory of the HMI device are displayed and edited in the recipe view.
Operating recipes 10.3 Recipes in the project Data flow The following figure shows the data flow in a project with recipes.
Operating recipes 10.4 Recipe displays 10.4 Recipe displays Displaying recipes You can display and edit recipes on the HMI device with a recipe view or recipe screen. Recipe view A recipe view is a screen object used to manage recipe data records. The recipe view shows recipe data records in tabular form.
Operating recipes 10.4 Recipe displays Simple recipe view The simple recipe view consists of three areas: ● Recipe list ● Record list ● Element list In the simple recipe view, each area is shown separately on the HMI device. Depending on the configuration, the simple recipe view starts with the recipe list or data record list. The following figure shows an example of the record list.
Operating recipes 10.4 Recipe displays Recipe screen A recipe screen allows the correlation between the plant and the recipe data to be displayed in graphic form. The configuration engineer combines I/O fields and screen objects to form a custom input screen. The configuration engineer can distribute the I/O fields of a recipe over several recipe screens, thus allowing recipe elements to be arranged by subject. The recipe screen can be operated using buttons configured accordingly.
Operating recipes 10.5 Recipe values in the HMI device and the PLC 10.5 Recipe values in the HMI device and the PLC Introduction You can change the values of a recipe on the HMI device and therefore influence the manufacturing process or a machine.
Operating recipes 10.6 Operating the recipe view Recipe tags online / offline The configuration engineer can configure a recipe so that changes to the values of the recipe tags do not have an immediate effect on the current process. Synchronization of the recipe values between the HMI device and the PLC depends on whether the configuration engineer has selected the settings "Tags online" or the setting "Tags offline" for a recipe.
Operating recipes 10.6 Operating the recipe view Operating elements of the recipe view The following table shows the operating elements of the recipe view. Buttons Key combination { } CTRL + CTRL + CTRL + * CTRL + CTRL + CTRL + CTRL + ENTER INS DEL = Functions Creates a new recipe data record. If a start value is configured, it is shown in the text box. Saves the displayed values of the recipe data record. The storage location is predefined by the project.
Operating recipes 10.6 Operating the recipe view Procedure using the touch screen Proceed as follows: 1. If the recipe view contains several recipes: Select the recipe for which you want to create a new recipe data record. . 2. Touch A new recipe data record with the next available number is created. If you change the new data record number to an existing data record number, the existing data record is overwritten. 3. Enter values for the elements of the data record.
Operating recipes 10.6 Operating the recipe view 10.6.3 Editing a recipe data record Introduction Edit the values of the recipe data records and save them in a recipe view. Synchronization with the PLC If you want to display the current recipe values from the PLC in the recipe view, you first have to read the current values from the PLC with . The values changed in the recipe view only become effective when the amended data record is transferred to the PLC by means of the button.
Operating recipes 10.6 Operating the recipe view 10.6.4 Deleting a recipe data record Introduction You can delete all the data records of a recipe which are not required. Requirements A screen with a recipe view is displayed. Procedure using the touch screen Proceed as follows: 1. If the recipe view contains several recipes: Select the recipe which contains the desired recipe data record. 2. Select the recipe data record you want to delete. . 3. Touch Procedure using the keys Proceed as follows: 1.
Operating recipes 10.6 Operating the recipe view 10.6.5 Synchronizing tags Introduction The values of the recipe elements can be saved to recipe tags, depending on the configuration. Differences may occur between the display values in the recipe view and the actual values of tags in an ongoing project. Synchronize the tags to equalize such differences. Synchronization always includes all the variables which belong to a recipe data record.
Operating recipes 10.6 Operating the recipe view 10.6.6 Reading a recipe data record from the PLC Introduction In the current project, the values which are also stored in the recipes in the HMI device can be changed directly in the plant. This is the case, for example, if a valve was opened further directly at the plant than is stored in the recipe. The values of the recipe data records saved in the HMI device possibly no longer match the values in the PLC.
Operating recipes 10.6 Operating the recipe view 10.6.7 Transferring a recipe data record to the PLC Introduction In order for an edited recipe data record to take effect in the process, you must transfer the values to the PLC. The display values in the recipe view are always transferred to the PLC. Requirements A screen with a recipe view is displayed. Procedure using the touch screen Proceed as follows: 1.
Operating recipes 10.7 Operating the simple recipe view 10.7 Operating the simple recipe view 10.7.1 Overview Introduction The simple recipe view consists of three areas: ● Recipe list ● Record list ● Element list You can use the context menu to operate each of these display areas.
Operating recipes 10.7 Operating the simple recipe view Context menus of the simple recipe view A number is assigned to each menu command which you can use to call the menu command with key control. With touch operation, touch the menu command to execute it. Some menu functions can also be called directly in the lists of the simple recipe view using the keys. ● Recipe list No.
Operating recipes 10.7 Operating the simple recipe view Key control of the menu Select the required entry using or . Press ENTER . Alternatively, press the numerical key with the number of the desired menu command. The command is executed. Operating the recipe screen You operate the recipes in a recipe screen with the operating elements provided by the configuration engineer. Further information on this may be available in your plant documentation. 10.7.
Operating recipes 10.7 Operating the simple recipe view 10.7.3 Editing a recipe data record Introduction Edit the values of the recipe data records in a simple recipe view. Synchronization with the PLC If you want to display the current recipe values from the PLC in the simple recipe view, you first have to read the current values from the PLC with the menu command "2 from PLC" in the element list.
Operating recipes 10.7 Operating the simple recipe view 10.7.4 Deleting a recipe data record Introduction You can delete all the data records which are not required. Requirements A screen with a simple recipe view is displayed. Procedure using the touch screen Proceed as follows: 1. If the recipe list contains several recipes: Select the recipe which contains the desired recipe data record. 2. Open the data record list. 3. Select the data record you want to delete. 4. Open the menu. 5.
Operating recipes 10.7 Operating the simple recipe view 10.7.5 Reading a recipe data record from the PLC Introduction The values of recipe elements are exchanged with the PLC via tags. In the current project, the values which are also stored in the recipes in the HMI device can be changed directly in the plant. This is the case, for example, if a valve was opened further directly at the plant than is stored in the recipe.
Operating recipes 10.7 Operating the simple recipe view 10.7.6 Transferring a recipe data record to the PLC Introduction In order for an edited recipe data record to take effect in the process, you must transfer the values to the PLC. The display values in the recipe view are always transferred to the PLC. Requirements A screen with a simple recipe view is displayed. Procedure Proceed as follows: 1.
Operating recipes 10.8 Importing a recipe data record 10.8 Importing a recipe data record Introduction You can import values from a CSV file to a recipe data record, depending on the configuration. Requirements ● An operating element with the function "Import data record" has been configured, for example a button ● A screen with a recipe view is displayed. Procedure Proceed as follows: 1.
Operating recipes 10.9 Exporting a recipe data record 10.9 Exporting a recipe data record Introduction You can export one or more recipe data records to a CSV file, depending on the configuration. After export, the values in the recipe data record can be further processed in a spreadsheet program such as MS Excel. The degree to which you can influence the export depends on the configuration. Requirements ● A screen with a recipe view is displayed.
Operating recipes 10.10 Examples 10.10 Examples 10.10.1 Entering a recipe data record Introduction You would like to enter production data on the HMI device without interrupting the process in the machine or plant. For this reason, the production data should not be transferred to the PLC. Procedure Proceed as follows: 1. Call the recipe view or a recipe screen. 2. Select the desired recipe data record. 3. Enter the values of the elements. 4. Save the recipe data record.
Operating recipes 10.10 Examples 10.10.2 Manual production sequence Introduction You request the production data of different workpieces from the PLC and display this data on the screen of the HMI device for inspection. You want to correct the transferred production data in the recipe view or the recipe screen if necessary. Procedure A scanner connected to the PLC reads the barcode of a workpiece. The barcode names correspond to the names in the recipe data record.
Maintenance and care 11.1 11 Maintaining and caring for the touch screen and keyboard overlay Introduction The HMI device is designed for maintenance-free operation. The touch screen and keyboard overlay should nevertheless be cleaned regularly. Requirement ● Damp cleaning cloth ● Washing up liquid or foaming screen cleaning agent Procedure NOTICE Unintentional response If you clean the touch screen or an HMI device with a keyboard overlay when it is switched on, you may cause maloperations.
Maintenance and care 11.2 Clean screen on MP 377 Touch 11.2 Clean screen on MP 377 Touch Introduction The HMI touch screen can be cleaned when it is switched on and a project is running. An operating element must be available in the project that can be used to call the "clean" screen. Once the clean screen is activated, touch screen operation is locked for a configured period of time. The time the touch screen is locked can be set between 5 and 30 seconds.
12 Technical specifications Dimension drawings 12.1.1 Dimension drawings of the MP 377 12" Touch 12.
Technical specifications 12.1 Dimension drawings Dimension drawings of the MP 377 12" Key 12.1.
Technical specifications 12.1 Dimension drawings Dimension drawings of the MP 377 15" Touch 12.1.
Technical specifications 12.1 Dimension drawings Dimension drawings of the MP 377 19" Touch 12.1.
Technical specifications 12.1 Dimension drawings Dimension drawings of the MP 377 PRO 15" Touch 12.1.
Technical specifications 12.2 Specifications 12.2 Specifications HMI device MP 377 12" Touch Weight without packaging 3.75 kg MP 377 12" Key 5.41 kg MP 377 15" Touch MP 377 PRO 15" Touch 4.69 kg Approx. 7.3 kg, with basic adapter approx. 7.7 kg MP 377 19" Touch 7.65 kg Display MP 377 12" Touch MP 377 12" Key Type Display area, active Resolution MP 377 15" Touch MP 377 PRO 15" Touch MP 377 19" Touch LCD TFT 246 mm x 184.5 mm (12.1") 304.1 mm x 228.1 mm (15") 376.3 mm x 301.
Technical specifications 12.2 Specifications Interfaces MP 377 12" Touch MP 377 12" Key 1 x RS 422/RS 485 MP 377 15" Touch MP 377 PRO 15" Touch MP 377 19" Touch Max. 12 Mbps, applies to DP operations 2 x USB 2.
Technical specifications 12.3 Bit assignment of the direct keys 12.3 Bit assignment of the direct keys The following figures show the assignment of the keys and LEDs to the bytes in the PLC process image. Further information may be available in your plant documentation. Note Do not use the LED bits "ACK", "A-Z", and "HELP" when a project is running on the HMI device.
Technical specifications 12.4 Description of the ports 12.4 Description of the ports 12.4.1 Power supply Plug connector, 2-pin Pin 12.4.2 Assignment 1 +24 VDC (L+) 2 GND 24 V (M) X10/IF 1B (RS 422/RS 485) Sub-D socket, 9-pin, with screw lock Pin 1) Assignment for the RS 422 Assignment for the RS 485 1 n. c. n. c.
Technical specifications 12.4 Description of the ports 12.4.3 X1 (PROFINET) RJ45 plug connector 12.4.4 Pin Assignment 1 Tx+ 2 Tx– 3 Rx+ 4 n. c. 5 n. c. 6 Rx– 7 n. c. 8 n. c. X20, X21 (USB) USB socket 284 Pin Assignment 1 +5 VDC, out (max.
Technical specifications 12.4 Description of the ports 12.4.
Technical specifications 12.
A Appendix A.1 ESD guideline Definition of ESD All electronic modules are equipped with large-scale integrated ICs or components. Due to their design, these electronic elements are highly sensitive to overvoltage, and thus to any electrostatic discharge. These electronic components are therefore specially identified as ESDs.
Appendix A.1 ESD guideline Anyone who is not connected to the electrical potential of their surroundings is subjected to electrostatic charging. 9ROWDJH The following figure indicates the maximum electrostatic charge anyone is subjected to when coming into contact with the materials shown. These values correspond with specifications to IEC 801-2.
Appendix A.2 System alarms A.2 System alarms Introduction System alarms on the HMI device provide information about internal states of the HMI device and PLC. The following overview shows the causes of system alarms and how to eliminate the cause of error. Some of the system alarms described in this section are relevant to individual HMI devices based on their range of features. Note System alarms are only indicated if an alarm window was configured.
Appendix A.2 System alarms Meaning of the system alarms All the system alarms that can be displayed are listed below. The system alarms are divided into different ranges: 10000 - Printer alarms Number Effect/cause Remedy 10000 The print job could not be started or was canceled due to an unknown error. Faulty printer setup. Or: No authorization is available for accessing the network printer. Power supply failure during data transfer. Check the printer settings, cable connections and the power supply.
Appendix A.2 System alarms 30000 - Alarms for IFwSetValue: SetValue() Number Effect/causes Remedy 30010 The tag could not accept the function result, e.g. when it has exceeded the value range. Check the tag type of the system function parameter. 30011 A system function could not be executed because the function was assigned an invalid value or type in the parameter. Check the parameter value and tag type of the invalid parameter. If a tag is used as a parameter, check its value.
Appendix A.2 System alarms 70000 - Win32 function alarms Number Effect/causes Remedy 70010 The application could not be started because it could not be found in the path specified or there is insufficient memory space. Check whether the application exists in the specified path or close other applications. 70011 The system time could not be modified. The error alarm only appears in connection with area pointer "Date/time PLC". Possible causes: • An invalid time was transferred in the job mailbox.
Appendix A.2 System alarms Number Effect/causes Remedy 70022 Acknowledgment to starting the Import Password List action. -- 70023 Acknowledgment to starting the Export Password List action. -- 70024 The value range of the tag has been exceeded in the system function. The calculation of the system function is not performed. Check the desired calculation and correct it if necessary. 70025 The value range of the tag has been exceeded in the system function.
Appendix A.2 System alarms Number Effect/causes Remedy 70036 No SMTP server for sending e-mails is configured. An attempt to connect to an SMTP server has failed and it is not possible to send e-mails. WinCC flexible Runtime generates the system alarm after the first attempt to send an e-mail. Configure an SMTP server: 70037 An e-mail cannot be sent for unknown reasons. The contents of the e-mail are lost. Check the e-mail parameters (recipient etc.).
Appendix A.2 System alarms Number Effect/causes Remedy 80012 Log entries are stored in a buffer. If the values are read to the buffer faster than they can be physically written (using a hard disk, for example), overloading may occur and recording is then stopped. Archive fewer values. Or: Increase the logging cycle. 80013 The overload status no longer applies. Archiving resumes the recording of all values. -- 80014 The same action was triggered twice in quick succession.
Appendix A.2 System alarms Number Effect/causes Remedy 80025 You have canceled the copy operation. Data written up to this point are retained. The destination log file (if configured) is not deleted. The cancellation is reported by an error entry $RT_ERR$ at the end of the destination log. -- 80026 This alarm is output after all logs are initialized. Values are written to the logs from then on.
Appendix A.2 System alarms Number Effect/causes Remedy 80045 The export of a log was interrupted due to an error in the connection to the server or at the server itself. The export is repeated automatically. Check: • The connection to the server • If the server is running • If there is enough free space on the server 80046 The destination file could not be written while exporting the log. Check whether there is enough space on the server and it you have permission to create the log file.
Appendix A.2 System alarms Number Effect/causes Remedy 90041 A user action which has to be logged has been executed without a logged on user. A user action requiring logging should only be possible with permission. Change the configuration by setting a required permission for the input object. 90044 A user action which has to be confirmed was blocked, because there is another user action pending. Repeat the user action if necessary.
Appendix A.2 System alarms 130000 - System information alarms Number Effect/causes Remedy 130000 The action was not executed. Close all other programs. Delete files no longer required from the hard disk. 130001 The action was not executed. Delete files no longer required from the hard disk. 130002 The action was not executed. Close all other programs. Delete files no longer required from the hard disk. 130003 No data medium found. The operation is canceled.
Appendix A.2 System alarms Number Effect/causes Remedy 140004 No tag update or write operations are executed because the access point or the module configuration is faulty. Verify the connection and check whether the PLC is switched on. Check the access point or the module configuration (MPI, PPI, PROFIBUS) in the Control Panel with "Set PG/PC interface". Restart the system. 140005 No tag updating or writing is executed because the Use a different HMI device address.
Appendix A.2 System alarms Number Effect/causes Remedy 140012 There is an initialization problem (e.g. when WinCC flexible Runtime was closed in Task Manager). Or: Another application (e.g.STEP7) with different bus parameters is active and the driver cannot be started with the new bus parameters (transmission rate, for example). Restart the HMI device. Or: Run WinCC flexible Runtime, then start your other applications. 140013 The MPI cable is disconnected and, thus, there is no power supply.
Appendix A.2 System alarms 160000 - Connection alarms IVar (WinLC) / OPC: Connection Number Effect/causes Remedy 160000 No more data is read or written. Possible causes: • The cable is defective • The PLC does not respond, is defective, etc. • The wrong port is used for the connection • System overload Ensure that the cable is plugged in, the PLC is operational, the correct port is being used. Restart the system if the system alarm persists.
Appendix A.2 System alarms Number Effect/causes Remedy 170004 An S7 diagnostics event cannot be visualized. The system returns an internal error of error class %2, error number %3. -- 170007 It is not possible to read the S7 diagnostics buffer -(SSL) because this operation was canceled with an internal error of class %2 and error code %3. 180000 - Misc/common alarms Number Effect/causes Remedy 180000 A component/OCX received configuration data with Install a newer component.
Appendix A.2 System alarms Number Effect/causes 190009 An attempt has been made to assign the tag a Observe the range of values for the data type of the value which is outside the permitted range of tags. values for this data type. For example, a value of 260 was entered for a byte tag or a value of -3 for an unsigned word tag. 190010 Too many values are written to the tag (for example, in a loop triggered by a script). Values are lost because only up to 100 actions are saved to the buffer.
Appendix A.2 System alarms 190100 - Area pointer alarms Number Effect/causes Remedy 190100 The area pointer is not updated because the address configured for this pointer does not exist. Type 1 Warnings 2 Errors 3 PLC acknowledgment 4 HMI device acknowledgment 5 LED mapping 6 Trend request 7 Trend transfer 1 8 Trend transfer 2 No.: Consecutive number displayed in WinCC flexible ES. Check the configuration.
Appendix A.2 System alarms 200100 - PLC user version alarms Number Effect/causes Remedy 200100 Coordination is not executed because the address configured in the PLC does not exist/is not set. Change the address or set up the address in the PLC. 200101 Coordination is canceled because the write access to the address configured in the PLC is not possible. Change the address or set the address in the PLC at an area which allows write access.
Appendix A.2 System alarms Number Effect/causes Remedy 220004 Communication is down and no update data is transferred because the cable is not connected or defective etc. Check the connection. 220005 Communication is up. -- 220006 The connection between the specified PLC and the specified port is active. -- 220007 The connection to the specified PLC is interrupted at the specified port.
Appendix A.2 System alarms Number Effect/causes Remedy 230202 WININET.DLL has detected an error. This error usually occurs when an attempt to connect to the server fails or the server refuses to connect because the client lacks the proper authorization. An unknown server certificate may also be the cause if the connection is encrypted by means of SSL. The alarm text provides details. This text is always in the language of the Windows installation because it is returned by the Windows OS.
Appendix A.2 System alarms Number Effect/causes Remedy 230306 Error in the connection to the remote server. This may Check whether occur as a result of network problems. • The bus cable is plugged in The attempt to connect failed. • There are network problems 230307 The connection to the remote server was shut down because • The remote server was shut down, or • The user instructed the server to close all connections -- The connection is closed.
Appendix A.2 System alarms Number Effect/causes Remedy 250002 The tag in the specified line in "Status Force" is not updated because it is not possible to map the PLC type in the tag type. Check the set address. 250003 An attempt to connect to the PLC failed. The tags are not updated. Check the connection to the PLC. Check that the PLC is switched on and is online.
Appendix A.2 System alarms Number Effect/causes Remedy 260025 The password you entered does not meet the necessary security guidelines. Enter a password that contains at least one special character. 260028 Upon system start-up, an attempt to log on, or when trying to change the password of a SIMATIC log-on user, the system attempts to access the SIMATIC Logon Server.
Appendix A.2 System alarms 270000 - System alarms Number Effect/causes Remedy 270000 A tag is not indicated in the alarm because it attempts to access an invalid address in the PLC. Check whether the data area for the tag exists in the PLC, the configured address is correct and the value range for the tag is correct. 270001 There is a device-specific limit as to how many alarms -may be queued for output (see the operating instructions). This limit has been exceeded.
Appendix A.2 System alarms Number Effect/causes Remedy 280003 The connection used requires a function block in the PLC. The function block has not responded. Check whether • The cable is plugged in • The PLC is OK • The correct port is used Restart the system if the system alarm persists. Remedy depends on the error code: 1: The function block must set the COM bit in the response container. 2: The function block must not set the ERROR bit in the response container.
Appendix A.2 System alarms Number Effect/causes Remedy 290007 There is a difference between the source and target structure of the recipe currently being processed. The target structure contains an additional data recipe tag which is not available in the source structure. The data recipe tag specified is assigned its start value. Insert the specified data recipe tag in the source structure.
Appendix A.2 System alarms Number Effect/causes Remedy 290026 An attempt has been made to read/write a record although the record is not free at present. This error may occur in the case of recipes for which downloading with synchronization has been configured. Set the record status to zero. 290027 Unable to connect to the PLC at present. As a result, the record can neither be read nor written.
Appendix A.2 System alarms Number Effect/causes Remedy 290057 The tags of the recipe specified were toggled from "offline" to "online" mode. Each change of a tag in this recipe is now immediately downloaded to the PLC. -- 290058 The tags of the specified recipe were toggled from "offline" to "online" mode. Modifications to tags in this recipe are no longer immediately transferred to the PLC but must be transferred there explicitly by downloading a record.
Appendix A.2 System alarms Number Effect/causes Remedy 290110 The default values could not be set due to an error. -- 290111 The Recipes subsystem cannot be used. Recipe views have no content and recipe-specific functions will not be performed. Transfer the project to the device again, together with the recipes (the corresponding check box in the Transfer dialog must be checked). Possible causes: • An error occurred while transferring the recipes. • The recipe structure was changed in ES.
Appendix A.2 System alarms Number Effect/causes Remedy 320005 The project contains ProAgent elements which are not In order to run the project, install the optional installed. ProAgent diagnostic functions cannot be ProAgent package. performed 320006 You have attempted to execute a function which is not Check the type of the selected unit. supported in the current constellation. 320007 No error-triggering addresses were found on the networks. ProAgent cannot indicate any faulty addresses.
Appendix A.2 System alarms 350000 - GUI alarms Number Effect/causes Remedy 350000 PROFIsafe packages have not arrived within the necessary period. There is a communication problem with the F-CPU. Check the WLAN connection. RT is terminated 350001 PROFIsafe packages have not arrived within the necessary period. There is a communication problem with the F-CPU. Check the WLAN connection. The PROFIsafe connection is re-established. 350002 An internal error has occurred.
Appendix A.
B Abbreviations ANSI American National Standards Institution CPU Central Processing Unit CSV Comma Separated Values CTS Clear To Send DC Direct Current DCD Data Carrier Detect DHCP Dynamic Host Configuration Protocol DIL Dual-in-Line (electronic chip housing design) DNS Domain Name System DP Distributed I/O DSN Data Source Name DSR Data Set Ready DTR Data Terminal Ready IO Input and Output ESD Components and modules endangered by electrostatic discharge EMC Electromagnetic C
Abbreviations 322 RxD Receive Data SD Card Security Digital Card SELV Safety Extra Low Voltage SP Service Pack PLC Programmable Logic Controller STN Super Twisted Nematic Sub-D Subminiature D (plug) TAB Tabulator TCP/IP Transmission Control Protocol/Internet Protocol TFT Thin Film Transistor TTY Teletype TxD Transmit Data UL Underwriter’s Laboratory USB Universal Serial Bus UPS Uninterruptible power supply WINS Windows Internet Naming Service MP 377, MP 377 PRO (WinCC flexi
Glossary "Transfer" mode An operating mode of the HMI device in which an executable project is transferred from the configuring PC to an HMI device. Acknowledge Acknowledgment of an alarm confirms that it has been noted. Alarm logging Output of user-specific alarms to a printer, in parallel to their output to the HMI device screen. Alarm, acknowledging Acknowledgment of an alarm confirms that it has been noted. Alarm, activated Moment at which an alarm is triggered by the PLC or HMI device.
Glossary Configuration software Software used to generate projects used for the purpose of process visualization. An example of configuring software is WinCC flexible. Configuring PC A configuring PC is a programming device or PC on which plant projects are created using an engineering software. Display duration Defines whether a system alarm is displayed on the HMI device and the duration of the display.
Glossary HMI device An HMI device is a device used for the operation and monitoring of machines and plants. The statuses of the machine or plant are indicated by means of graphic elements or by indicator lamps on the HMI device. The operating elements of the HMI device allow the operator to interact with the processes of the machine or plant. HMI device image A file that can be transferred from the configuring PC to the HMI device.
Glossary Process visualization Visualization of technical processes by means of text and graphic elements. Configured plant screens allow operator intervention in active plant processes by means of the input and output data. Project Result of a configuration using a configuration software. The project normally contains several screens with embedded system-specific objects, basic settings and alarms. The project file of a project configured in WinCC flexible is saved under the file name extension *.hmi.
Glossary Screen Form of the visualization of all logically related process data for a plant. The visualization of the process data can be supported by graphic objects. Screen object Configured object used to display or operate the plant, e.g. rectangle, I/O field or alarm view. STEP 7 STEP 7 is the programming software for SIMATIC S7, SIMATIC C7 and SIMATIC WinAC PLCs. STEP 7 Micro/WIN STEP 7 Micro/WIN is the programming software for SIMATIC S7-200 PLCs.
Glossary 328 MP 377, MP 377 PRO (WinCC flexible) Operating Instructions, 10/2008, 6AV6691-1DR01-0AB0
Index / /Audit, 32 A Accessory kit, 25 ACK, 239 ACK key, 203 Acknowledge Alarm, 203, 243 Error alarm, 243 Acknowledge key, 203 Acoustic feedback, 191 Acoustic signal, 196 For inadvertent operation, 191 with inadvertent operation, 99 Acoustics Feedback, 122, 124 Address assignment TCP/IP network, 145 Addressing, 142 Admin, 233, 234, 235 Alarm, 237 Acknowledge, 203, 243 Editing, 244 Functional scope, 29 LED, 240 Alarm buffer, 238 Functional scope, 29 Alarm class, 238, 241 Alarm event, 237 Alarm group, 238 Al
Index Calibrating Touch screen, 98, 110 Cancel Secure mode, 94 Cancel Password protection, 113 Cancel key, 104, 202 Care, 273 CE approval, 39 Certificate Delete, 98, 152 Importing, 98, 152 LED, 98 Changing Brightness, 118 User data, 233, 234 Character repeat, 98 Screen keyboard, 107 Clean screen, 274 Cleaning product, 273 Clearance MP 377, 49 Climatic Storage conditions, 44 Transport conditions, 44 Closing Project, 236 Rear wall, 80 Column sequence Alarm view, 241 Compatibility conflict, 168 Conductor cros
Index Delete Certificate, 98, 152 Recipe data record, 258, 266 Users, 235 Delete key, 104, 202 Device name For network operation, 144 Setting, 99 Dewing, 44 DHCP, 146 DIP switch Setting, 70 Direct key, 192 Bit assignment, 282 Functional scope, 31 Display MP 377, 280 Display format, 205 Displaying Info text, 200, 209 Information on the MP 377, 127 Infotext, 203 Memory information, 129 System information, 129 Disposal, 5 Disturbance Pulse-shaped, 42 Sinusoidal, 43 DNS, 146 Server, 142 Documentation Enclosed,
Index Factory settings, 73 Feedback Acoustic, 122, 124, 191 Optical, 191 FM Approval, 40 FN key, 105, 202 Front view, 15, 17, 19, 21, 23 Function Additional, 31 Function key Labeling, 86 Function keys, 82 Global assignment, 204 Local assignment, 204 Function test, 78 Functional scope Alarm buffer, 29 ALARM_S, 29 Alarms, 29 Graphics list, 29 Info text, 31 Limit value monitoring, 29 Log, 30 Recipe, 30 Safety, 31 Scaling, 29 Screen, 30 Tags, 29 Text list, 29 G Gauge, 210 Graphics list Functional scope, 29 Gr
Index Ethernet, 146 Setting, 98 K Key ACK, 203 ALT, 105, 202 A-Z, 105, 202 Backspace, 202 Cancel, 104 CTRL, 105, 202 Cursor, 104, 201 Delete, 104, 202 END, 104, 201 ENTER, 104, 202 ESC, 104, 202 FN, 105, 202 HOME, 104, 201 Infotext, 203 Scroll back, 104, 201 Scroll forward, 104, 201 SHIFT, 105, 202 TAB, 104, 201 Tabulator, 104 Key combination Entering, 105, 202 Key control, 201, 205 Trend view, 214 Keyboard External, 100 Safety instruction, 82 Keyboard properties, 98 L Labeling Approvals, 40 EC Declarati
Index Restoring file system, 116 Unplug, 85 Memory information, 99 Displaying, 129 LED, 128 Memory management, 98, 158 Menu command Simple recipe view, 263 Microsoft Excel Viewer, 32 Microsoft PDF Viewer, 32 Microsoft Word Viewer, 32 Monitoring mode Sm@rtClient view, 221 Mounting, 48 EMC-compatible, 42 HMI device, 57, 59 Mounting clamp, 56 Mounting clamp Mounting, 55, 56 Mounting cutout Dimensions, 49 Preparing, 49 Mounting location, 48, 51 Mounting position, 47 Thin Client 15, 51 Mouse External, 100 Mouse
Index Offline Operating mode, 160 Recipe tag, 254 Test, 167 Online Operating mode, 160 Recipe tag, 254 Test, 167 OP properties, 98 Device, 127 Memory monitoring, 158 Persistent storage, 117 Touch, 110 OPC server, 32 Open Control Panel, 97 Drop down list box, 104, 202 Opening Loader, 90 Operating Control Panel, 100, 102 Explorer, 91 Feedback, 190 Key, 201, 205 Loader, 90 Operating element, 104, 201 Project, 189 Recipe screen, 255, 264 Slider control, 215 Switches, 211 Trend view, 213 Windows CE interface, 9
Index Setting, 99 State, 99 Wiring diagram, 65 Precautions Electrostatic discharge, 288 Printer Connecting, 75 Setting properties, 98 Wiring diagram, 75 Printer connection Setting, 120 Printer properties, 98, 121 Printing Labeling strips, 86 Via network printer, 143 ProAgent, 32 Process control phase, 159 Production sequence Manual, 272 PROFIBUS DP Setting, 99, 140 PROFINET, 142 Addressing, 142 Connecting, 69 PROFINET IO Communication, 69 Communication fault, 33 Disabling direct keys, 134 Enabling direct k
Index Remote control Forcing permission, 222, 223 Start, 222, 223 Removing Option, 162, 182, 184, 186 Repairs, 274 Reset to factory setting, 162 Restore, 98, 153, 168 Restoring, 162, 170, 172, 225 from external storage device, 98, 155 From memory card, 116 With ProSave, 172 With WinCC flexible, 170 Restoring factory settings, 73 Returns Center, 274 Reverse polarity protection, 66 RS 422 to RS 232 converter, 26 RS-422/RS-485 port Configuring, 70 Ruler Trend view, 213 S S7 transfer settings, 99 Safe electri
Index Password protection, 112 Secure mode, 94 Setting Backlighting, 99 Browser, 98 Date, 114 Date format, 116 Date/Time, 98 Delay time, 99, 131 Device name, 99 DIP switch, 70 Double-click, 108 E-Mail, 99 E-mail connection, 148 IP address, 98 Language, 193 MPI, 99, 140 Name server, 98 Network, 145 Number format, 116 Operation feedback, 99 PC/PPI adapter, 72 Power supply, 99 Printer connection, 120 Printer properties, 98 PROFIBUS, 140 PROFIBUS DP, 99 PROFINET IO, 98 Proxy, 98 Regional data, 116 Screen saver
Index System properties, 99 Device name, 144 General, 128 Memory, 129 T TAB key, 104, 201 Tabulator key, 104, 201 Tags Functional scope, 29 Task planner Functional scope, 31 Taskbar, 89 TCP/IP address, 145 Technical specifications Display, 280 Input device, 280 Interfaces, 281 Memory, 280 MP 377, 280 Supply voltage, 281 Technical support, 5 Temporary files Backup, 116 Test For ambient conditions, 46 Test voltage, 52 Testing MP 377, 77 Text box, 194 Character mode, 202 Normal mode, 202 Text list Functional
Index In residential areas, 41 Industrial, 41 With additional measures, 45 User data Backup, 225 Changing, 233, 234 Restoring, 225 User group, 224 User name, 147 User view, 226 Expanded, 226 Simple, 226 Users, 225 Admin, 233, 234, 235 Changing, 229 Creating, key control, 230 Delete, 235 Logoff, 228 Logon, 227 PLC_User, 233, 234, 235 V Value table Trend view, 213 VBScript Functional scope, 31 340 Volume, 122 Setting, 99 Volume & Sounds Properties, 99 W Weight MP 377, 280 WinCC flexible internet settings
