Operating instructions

ManualsBrandsSiemens ManualsComputer equipmentSIMATIC IPC627C

100

Table Of Contents

SIMATIC IPC627C
Legal information
Table of contents
1 Introduction
- 1.1 Preface
- 1.2 Guideline to the operating instructions
2 Safety notes
- 2.1 General safety instructions
3 Description
- 3.1 Overview
- 3.2 Areas of application
- 3.3 Benefits
- 3.4 Function
- 3.5 Features
- 3.6 Windows Embedded Standard 2009
- 3.7 Design
4 Application planning
- 4.1 Transport
- 4.2 Unpacking and checking the delivery unit
- 4.3 Device identification data
- 4.4 Ambient and environmental conditions
- 4.5 Permitted mounting positions
5 Mounting
- 5.1 Installing the device
- 5.2 Installing the device with mounting brackets
- 5.3 Installing the device with the vertical mounting kit
- 5.4 Installing the device with the vertical mounting kit for PC port access from the front
6 Connecting
- 6.1 Connecting peripherals
- 6.2 Connecting the 100 - 240 V AC Power Supply
- 6.3 Connecting the (24 V) DC power supply
- 6.4 Connecting equipotential bonding
- 6.5 Connecting Ethernet/USB strain relief
- 6.6 Connecting the PROFINET strain relief
7 Commissioning
- 7.1 Requirements for commissioning
- 7.2 Basic commissioning - initial startup
- 7.3 Windows XP, Windows 7 Security Center
- 7.4 Switching off the device
- 7.5 Notes on operation
8 Integration
- 8.1 Integration into an automation system
- 8.2 PROFINET
9 Functions
- 9.1 Introduction
- 9.2 Temperature monitoring
- 9.3 Watchdog (WD)
- 9.4 Fan monitoring
- 9.5 Status display
- 9.6 SRAM buffer memory
- 9.7 Battery monitoring
- 9.8 AMT (Active Management Technology)
10 Expansion and parameter assignment
- 10.1 Opening the Device
- 10.2 Memory expansion
  - 10.2.1 Removing/Installing Memory Module
- 10.3 Installing PCI/PCIe cards
  - 10.3.1 Notes on the modules
  - 10.3.2 Installing / removing expansion modules
- 10.4 Installing drives
- 10.5 Installing/removing an on-board Compact Flash card
- 10.6 Installing/removing an additional Compact Flash card
11 Service and maintenance
- 11.1 Removing and installing hardware components
- 11.2 Reinstalling the software
- 11.3 Installing the RAID Controller software
- 11.4 BIOS update
- 11.5 BIOS Recovery
12 Alarm, error, and system messages
- 12.1 Boot error messages
- 12.2 BIOS beep codes
13 Troubleshooting/FAQs
- 13.1 General problems
- 13.2 Problems when Using Modules of Third-party Manufacturers
- 13.3 Display a temperature error by means of the DiagBase application
14 Technical data
- 14.1 General Specifications
- 14.2 Current/power requirements of the device
- 14.3 AC voltage supply
- 14.4 DC power supply
15 Dimension drawings
- 15.1 Overview of the dimensional drawings
- 15.2 Dimensional drawings of the device
- 15.3 Dimensional drawings for the installation of expansion modules
16 Detailed descriptions
- 16.1 Motherboard
- 16.2 Bus board
- 16.3 System resources
  - 16.3.1 Currently allocated system resources
  - 16.3.2 System resources used by the BIOS/DOS
- 16.4 BIOS-Setup
- 16.5 AMT (Active Management Technology)
- 16.6 Communications processor CP 1616 onboard
A Appendix
- A.1 Guidelines and declarations
- A.2 Certificates and approvals
- A.3 Service and support
B ESD guidelines
C List of abbreviations
- C.1 Abbreviations
Glossary
Index
- "
- 2
- A
- B
- C
- D
- E
- F
- G
- H
- I
- L
- M
- O
- P
- R
- S
- T
- U
- V
- W

Service and maintenance

11.2 Reinstalling the software

SIMATIC IPC627C

Operating Instructions, 11/2010, A5E02669068-02

Restoring factory state

To restore the delivery state:

● Place the Restore DVD into the drive and restart the device using the on/off switch.

● When BIOS outputs the message

Press <F2> to enter Setup or <F12> to show Boot menu press F12.

The "Boot Menu" is displayed when initialization is completed.

● Select the optical drive using the cursor keys.

● Follow the on-screen instructions.

CAUTION

All existing data, programs, user settings and authorizations or license keys will be

deleted from the hard disk and are therefore lost.

For information on the functions, refer to the README.TXT file on the Restore DVD.

11.2.3 Installing Windows

11.2.3.1 Installing Windows

Use the Recovery DVD to install Windows to suit your particular requirements. You also

need the supplied Documentation and Drivers DVD. Additional controllers unknown to the

operating system must be made known to the recovery system and to the Windows

operating system.

1. Press the F6 or the "Load Driver" icon key while booting and follow the on-screen

instructions. During the rest of the installation, you will be asked several times for the

missing driver of the controller.

Booting with the Recovery DVD

1. To boot the Recovery DVD press when BIOS outputs the message

Press <F2> to enter SETUP or <F12> to display the boot menu.

press the F12 key. The boot menu displayed after initialization indicates all boot devices.

2. Select the DVD drive.

Follow the instructions on the screen until the "Siemens SIMATIC Recovery" window is

displayed.

When using the recovery function of Windows 7, confirm that you want to boot from DVD

immediately at startup. Otherwise the system boots from hard disk if you have a bootable

hard disk installed.

The following sections describe older Windows operating systems. The Recovery for

Windows 7 is described in the section Recovery of Windows 7 (Page 95).