Operating instructions

ManualsBrandsSiemens ManualsComputer equipmentSIMATIC IPC627C

Table Of Contents

SIMATIC IPC627C
Legal information
Table of contents
1 Introduction
- 1.1 Preface
- 1.2 Guideline to the operating instructions
2 Safety notes
- 2.1 General safety instructions
3 Description
- 3.1 Overview
- 3.2 Areas of application
- 3.3 Benefits
- 3.4 Function
- 3.5 Features
- 3.6 Windows Embedded Standard 2009
- 3.7 Design
4 Application planning
- 4.1 Transport
- 4.2 Unpacking and checking the delivery unit
- 4.3 Device identification data
- 4.4 Ambient and environmental conditions
- 4.5 Permitted mounting positions
5 Mounting
- 5.1 Installing the device
- 5.2 Installing the device with mounting brackets
- 5.3 Installing the device with the vertical mounting kit
- 5.4 Installing the device with the vertical mounting kit for PC port access from the front
6 Connecting
- 6.1 Connecting peripherals
- 6.2 Connecting the 100 - 240 V AC Power Supply
- 6.3 Connecting the (24 V) DC power supply
- 6.4 Connecting equipotential bonding
- 6.5 Connecting Ethernet/USB strain relief
- 6.6 Connecting the PROFINET strain relief
7 Commissioning
- 7.1 Requirements for commissioning
- 7.2 Basic commissioning - initial startup
- 7.3 Windows XP, Windows 7 Security Center
- 7.4 Switching off the device
- 7.5 Notes on operation
8 Integration
- 8.1 Integration into an automation system
- 8.2 PROFINET
9 Functions
- 9.1 Introduction
- 9.2 Temperature monitoring
- 9.3 Watchdog (WD)
- 9.4 Fan monitoring
- 9.5 Status display
- 9.6 SRAM buffer memory
- 9.7 Battery monitoring
- 9.8 AMT (Active Management Technology)
10 Expansion and parameter assignment
- 10.1 Opening the Device
- 10.2 Memory expansion
  - 10.2.1 Removing/Installing Memory Module
- 10.3 Installing PCI/PCIe cards
  - 10.3.1 Notes on the modules
  - 10.3.2 Installing / removing expansion modules
- 10.4 Installing drives
- 10.5 Installing/removing an on-board Compact Flash card
- 10.6 Installing/removing an additional Compact Flash card
11 Service and maintenance
- 11.1 Removing and installing hardware components
- 11.2 Reinstalling the software
- 11.3 Installing the RAID Controller software
- 11.4 BIOS update
- 11.5 BIOS Recovery
12 Alarm, error, and system messages
- 12.1 Boot error messages
- 12.2 BIOS beep codes
13 Troubleshooting/FAQs
- 13.1 General problems
- 13.2 Problems when Using Modules of Third-party Manufacturers
- 13.3 Display a temperature error by means of the DiagBase application
14 Technical data
- 14.1 General Specifications
- 14.2 Current/power requirements of the device
- 14.3 AC voltage supply
- 14.4 DC power supply
15 Dimension drawings
- 15.1 Overview of the dimensional drawings
- 15.2 Dimensional drawings of the device
- 15.3 Dimensional drawings for the installation of expansion modules
16 Detailed descriptions
- 16.1 Motherboard
- 16.2 Bus board
- 16.3 System resources
  - 16.3.1 Currently allocated system resources
  - 16.3.2 System resources used by the BIOS/DOS
- 16.4 BIOS-Setup
- 16.5 AMT (Active Management Technology)
- 16.6 Communications processor CP 1616 onboard
A Appendix
- A.1 Guidelines and declarations
- A.2 Certificates and approvals
- A.3 Service and support
B ESD guidelines
C List of abbreviations
- C.1 Abbreviations
Glossary
Index
- "
- 2
- A
- B
- C
- D
- E
- F
- G
- H
- I
- L
- M
- O
- P
- R
- S
- T
- U
- V
- W

Description

3.7 Design

SIMATIC IPC627C

Operating Instructions, 11/2010, A5E02669068-02

3.7.2 Operator Controls

On/Off switch

On/Off switch Description

Switch the device on using the on/off switch. This requires

that the BIOS Setup entry "After Power Failure" is set to

"Power On".

WARNING

The on/off switch does not isolate the device from the mains! When the switch is in 0

position (Off), the device is still supplied with mains voltage in order to generated the

internal auxiliary voltage for the power supply.

NOTICE

Terminate the operating system before shutting down the device with the on/off switch,

otherwise data may be lost.