Operating instructions

ManualsBrandsSiemens ManualsComputer equipmentSIMATIC IPC627C

151

152

153

154

155

156

157

158

159

160

Table Of Contents

SIMATIC IPC627C
Legal information
Table of contents
1 Introduction
- 1.1 Preface
- 1.2 Guideline to the operating instructions
2 Safety notes
- 2.1 General safety instructions
3 Description
- 3.1 Overview
- 3.2 Areas of application
- 3.3 Benefits
- 3.4 Function
- 3.5 Features
- 3.6 Windows Embedded Standard 2009
- 3.7 Design
4 Application planning
- 4.1 Transport
- 4.2 Unpacking and checking the delivery unit
- 4.3 Device identification data
- 4.4 Ambient and environmental conditions
- 4.5 Permitted mounting positions
5 Mounting
- 5.1 Installing the device
- 5.2 Installing the device with mounting brackets
- 5.3 Installing the device with the vertical mounting kit
- 5.4 Installing the device with the vertical mounting kit for PC port access from the front
6 Connecting
- 6.1 Connecting peripherals
- 6.2 Connecting the 100 - 240 V AC Power Supply
- 6.3 Connecting the (24 V) DC power supply
- 6.4 Connecting equipotential bonding
- 6.5 Connecting Ethernet/USB strain relief
- 6.6 Connecting the PROFINET strain relief
7 Commissioning
- 7.1 Requirements for commissioning
- 7.2 Basic commissioning - initial startup
- 7.3 Windows XP, Windows 7 Security Center
- 7.4 Switching off the device
- 7.5 Notes on operation
8 Integration
- 8.1 Integration into an automation system
- 8.2 PROFINET
9 Functions
- 9.1 Introduction
- 9.2 Temperature monitoring
- 9.3 Watchdog (WD)
- 9.4 Fan monitoring
- 9.5 Status display
- 9.6 SRAM buffer memory
- 9.7 Battery monitoring
- 9.8 AMT (Active Management Technology)
10 Expansion and parameter assignment
- 10.1 Opening the Device
- 10.2 Memory expansion
  - 10.2.1 Removing/Installing Memory Module
- 10.3 Installing PCI/PCIe cards
  - 10.3.1 Notes on the modules
  - 10.3.2 Installing / removing expansion modules
- 10.4 Installing drives
- 10.5 Installing/removing an on-board Compact Flash card
- 10.6 Installing/removing an additional Compact Flash card
11 Service and maintenance
- 11.1 Removing and installing hardware components
- 11.2 Reinstalling the software
- 11.3 Installing the RAID Controller software
- 11.4 BIOS update
- 11.5 BIOS Recovery
12 Alarm, error, and system messages
- 12.1 Boot error messages
- 12.2 BIOS beep codes
13 Troubleshooting/FAQs
- 13.1 General problems
- 13.2 Problems when Using Modules of Third-party Manufacturers
- 13.3 Display a temperature error by means of the DiagBase application
14 Technical data
- 14.1 General Specifications
- 14.2 Current/power requirements of the device
- 14.3 AC voltage supply
- 14.4 DC power supply
15 Dimension drawings
- 15.1 Overview of the dimensional drawings
- 15.2 Dimensional drawings of the device
- 15.3 Dimensional drawings for the installation of expansion modules
16 Detailed descriptions
- 16.1 Motherboard
- 16.2 Bus board
- 16.3 System resources
  - 16.3.1 Currently allocated system resources
  - 16.3.2 System resources used by the BIOS/DOS
- 16.4 BIOS-Setup
- 16.5 AMT (Active Management Technology)
- 16.6 Communications processor CP 1616 onboard
A Appendix
- A.1 Guidelines and declarations
- A.2 Certificates and approvals
- A.3 Service and support
B ESD guidelines
C List of abbreviations
- C.1 Abbreviations
Glossary
Index
- "
- 2
- A
- B
- C
- D
- E
- F
- G
- H
- I
- L
- M
- O
- P
- R
- S
- T
- U
- V
- W

Detailed descriptions

16.4 BIOS-Setup

SIMATIC IPC627C

Operating Instructions, 11/2010, A5E02669068-02

157

Entry Meaning

Internal COM 1 Enable (Enabled) or disable (Disabled) the serial port or configure it

automatically (Auto)

With Enabled, it is possible to specify the I/O base address and the

interrupt.

AUTO: BIOS switches on the COM. Resources are assigned in the

OS per reconfiguration.

Onboard Ethernet 1: Enable or disable the onboard Ethernet 1 interface.

Ethernet 1 Address: Display the MAC address of Ethernet 1

Onboard Ethernet 1: Enable or disable the onboard Ethernet 2 interface.

Ethernet 1 Address: Display the MAC address of Ethernet 2

PCI – MPI / DP / PROFINET: Enable or disable the onboard MPI/DP or PROFINET interface.

Advanced menu > SATA/PATA Configuration

Figure 16-8 "SATA/PATA Configuration" submenu

Entry Meaning

SATA Controller Enable or disable the SATA and PATA controllers.

SATA Controller mode Set operating mode of the SATA controller:

 Enhanced: SATA Ports 0-3 operate in Legacy mode, SATA

Ports 4-5 in native IDE mode

 AHCI : Disable or enable the AHCI support

 RAID: Disables or enables RAID support

Serial ATA Port 0 Submenu for SATA Port 0 configuration

Serial ATA Port 1 Submenu for SATA Port 1 configuration

Serial ATA Port 2 Submenu for SATA Port 2 configuration

Serial ATA Port 3 Submenu for SATA Port 3 configuration

Serial ATA Port 4 Submenu for SATA Port 4 configuration

Serial ATA Port 5 Submenu for SATA Port 5 configuration