Optipoint 500- User Manual
Table Of Contents
- Before You Begin
- Basic operating instructions
- Making Calls – Basic Functions
- Answering Calls
- Switching to Speakerphone Mode
- Switching to the Handset
- Open Listening in the Room During a Call
- Making Calls
- Ending the call
- Redialing a Number
- Turning the Microphone On and Off
- Calling a Second Party (ConsultationHold)
- Call Forwarding
- Using Callback
- Saving Repertory Dialing Numbers on a Key
- Telephone Settings
- Adjusting the Ring Volume
- Adjusting the Ring Tone
- Adjusting the Attention Ring Volume
- Adjusting the Speakerphone to the Room Acoustics
- Adjusting the Receiving Volume During a Call
- Adjusting the Display to a Comfortable Reading Angle
- Display backlight
- Adjusting the display contrast
- Selecting the Language of Screen Prompts
- Making Calls – Convenience Functions
- Answering Calls
- Dialing/Making Calls
- Dialing a Number From the Internal Directory
- During a Call
- Using Call Waiting
- Accepting a Waiting Call (Camp-On)
- Preventing and Allowing Call Waiting (AutomaticCamp-On)
- Turning the Call Waiting Tone On and Off
- Parking a Call
- Placing External Calls on Hold
- Conducting a Conference
- Ending a Conference (Initiator Only)
- Activating Tone Dialing/DTMFSuffix-Dialing
- Transferring a Call after a Speaker Call (Announcement) inaGroup
- Trunk Flash (Not for HiPath500)
- If You Cannot Reach a Destination ...
- Using Night Answer
- Saving Functions, Procedures and Appointments
- Displaying and Assigning Call Charges
- Private Sphere/Security
- Using Other Functions
- Sending a Message
- Leaving an Advisory Message
- Display Number of Waiting Calls and Overload Indication
- Using Another Telephone Like Your Own for a Call
- Change call number (relocate)
- Fax Details and Message on Answering Machine
- Resetting Services and Functions (System-Wide Cancellation for a Telephone)
- Activating Functions for Another Telephone
- Using System Functions from the Outside (DISA: Direct Inward System Access)
- Using functions in ISDN via code dialing (keypad dialing)
- Controlling Connected Computers or Other Programs and Telephone Data Service (NotforHiPath500))
- Controlling Relays (Not forHiPath500)
- Sensors (HiPath3300/3350/3500/3550 Only)
- Radio Paging (Not for U.S., Not for HiPath500)
- Using Other Team Functions
- Team and Executive/Secretary Functions With Trunk Keys
- Using Trunk Keys
- Forwarding Calls on Lines
- Using DSS Keys
- Transferring a Call in Progress
- Accepting a Call for Another Team Member
- Joining or Leaving a Group Call (Not for the Executive Telephone in an Executive/Secretary Team)
- Transferring Calls Directly to the Executive (Only in an Executive/Secretary Group)
- Testing the Telephone
- Special Functions in the LAN (Not for HiPath500)
- Different Displays in a HiPath4000 Environment (NotforHiPath500)
- Labeling, Documentation
- Fixing Problems
- Index
- Overview of Functions/Codes (Alphabetical)
- FCC and Industry Canada Compliance
Step by Step
Private Sphere/Security
74
Trace Call: Identifying Anonymous
Callers (Not for U.S.)
You can have the carrier identify malicious external call-
ers. You can save the caller’s station number during the
call or for 30 seconds after the call ends. However, it is
essential that you do not replace your handset during
this time.
Press the key. The LED lights up.
and
Select and confirm.
or
qlh Enter the code.
Program/Service
*
84=Trace call?
After you have finished tracing the call, the data
is stored on the carrier’s system. Now contact
your service personnel.