Optipoint 500- User Manual
Table Of Contents
- Before You Begin
- Basic operating instructions
- Making Calls – Basic Functions
- Answering Calls
- Switching to Speakerphone Mode
- Switching to the Handset
- Open Listening in the Room During a Call
- Making Calls
- Ending the call
- Redialing a Number
- Turning the Microphone On and Off
- Calling a Second Party (ConsultationHold)
- Call Forwarding
- Using Callback
- Saving Repertory Dialing Numbers on a Key
- Telephone Settings
- Adjusting the Ring Volume
- Adjusting the Ring Tone
- Adjusting the Attention Ring Volume
- Adjusting the Speakerphone to the Room Acoustics
- Adjusting the Receiving Volume During a Call
- Adjusting the Display to a Comfortable Reading Angle
- Display backlight
- Adjusting the display contrast
- Selecting the Language of Screen Prompts
- Making Calls – Convenience Functions
- Answering Calls
- Dialing/Making Calls
- Dialing a Number From the Internal Directory
- During a Call
- Using Call Waiting
- Accepting a Waiting Call (Camp-On)
- Preventing and Allowing Call Waiting (AutomaticCamp-On)
- Turning the Call Waiting Tone On and Off
- Parking a Call
- Placing External Calls on Hold
- Conducting a Conference
- Ending a Conference (Initiator Only)
- Activating Tone Dialing/DTMFSuffix-Dialing
- Transferring a Call after a Speaker Call (Announcement) inaGroup
- Trunk Flash (Not for HiPath500)
- If You Cannot Reach a Destination ...
- Using Night Answer
- Saving Functions, Procedures and Appointments
- Displaying and Assigning Call Charges
- Private Sphere/Security
- Using Other Functions
- Sending a Message
- Leaving an Advisory Message
- Display Number of Waiting Calls and Overload Indication
- Using Another Telephone Like Your Own for a Call
- Change call number (relocate)
- Fax Details and Message on Answering Machine
- Resetting Services and Functions (System-Wide Cancellation for a Telephone)
- Activating Functions for Another Telephone
- Using System Functions from the Outside (DISA: Direct Inward System Access)
- Using functions in ISDN via code dialing (keypad dialing)
- Controlling Connected Computers or Other Programs and Telephone Data Service (NotforHiPath500))
- Controlling Relays (Not forHiPath500)
- Sensors (HiPath3300/3350/3500/3550 Only)
- Radio Paging (Not for U.S., Not for HiPath500)
- Using Other Team Functions
- Team and Executive/Secretary Functions With Trunk Keys
- Using Trunk Keys
- Forwarding Calls on Lines
- Using DSS Keys
- Transferring a Call in Progress
- Accepting a Call for Another Team Member
- Joining or Leaving a Group Call (Not for the Executive Telephone in an Executive/Secretary Team)
- Transferring Calls Directly to the Executive (Only in an Executive/Secretary Group)
- Testing the Telephone
- Special Functions in the LAN (Not for HiPath500)
- Different Displays in a HiPath4000 Environment (NotforHiPath500)
- Labeling, Documentation
- Fixing Problems
- Index
- Overview of Functions/Codes (Alphabetical)
- FCC and Industry Canada Compliance
Before You Begin
2
Before You Begin
These operating instructions describe the optiPoint 500 economy, optiPoint 500 basic,
optiPoint 500 standard and telephones on your HiPath 500 and HiPath 3000 / 5000.
They describe all functions you can use from your telephone. You may find that some func-
tions you wish to use are not avai l ble on your telephone. This may be due to one of the
following reasons:
• The function has not been configured for your telephone - address any questions to
your service personnel.
• Your communications platform does not supp ort this function - contact your service
personnel to upgrade your system.
Important Notes
CE (customer equipment) does not continue to support emergency dialing after loss of
mains power, if battery back up and power fail switchover to emergency analogue phones
is not available.
Never allow the telephone to come into contact with staining or aggressive liquids such as
coffee, tea, juice, or soft drinks. For information on telephone maintenance Æ Page 117.
The information provided in this document contains merely general descriptions or charac-
teristics of performance which in case of actual use do not always apply as described or
which may change as a result of further development of the products.
An obligation to provide the respective characteristics shall only exist if expressly agreed
in the terms of contract.
Do not operate the telephone in environments where there is a danger
of explosions.
Use only original Siemens accessories Æ Page 114. Using other acces-
sories may cause a hazard and will invalidate the warranty and the CE
mark.
Never open the telephone or a key module. If you encounter any prob-
lems, contact your service personnel.