Optipoint 500- User Manual
Table Of Contents
- Before You Begin
- Basic operating instructions
- Making Calls – Basic Functions
- Answering Calls
- Switching to Speakerphone Mode
- Switching to the Handset
- Open Listening in the Room During a Call
- Making Calls
- Ending the call
- Redialing a Number
- Turning the Microphone On and Off
- Calling a Second Party (ConsultationHold)
- Call Forwarding
- Using Callback
- Saving Repertory Dialing Numbers on a Key
- Telephone Settings
- Adjusting the Ring Volume
- Adjusting the Ring Tone
- Adjusting the Attention Ring Volume
- Adjusting the Speakerphone to the Room Acoustics
- Adjusting the Receiving Volume During a Call
- Adjusting the Display to a Comfortable Reading Angle
- Display backlight
- Adjusting the display contrast
- Selecting the Language of Screen Prompts
- Making Calls – Convenience Functions
- Answering Calls
- Dialing/Making Calls
- Dialing a Number From the Internal Directory
- During a Call
- Using Call Waiting
- Accepting a Waiting Call (Camp-On)
- Preventing and Allowing Call Waiting (AutomaticCamp-On)
- Turning the Call Waiting Tone On and Off
- Parking a Call
- Placing External Calls on Hold
- Conducting a Conference
- Ending a Conference (Initiator Only)
- Activating Tone Dialing/DTMFSuffix-Dialing
- Transferring a Call after a Speaker Call (Announcement) inaGroup
- Trunk Flash (Not for HiPath500)
- If You Cannot Reach a Destination ...
- Using Night Answer
- Saving Functions, Procedures and Appointments
- Displaying and Assigning Call Charges
- Private Sphere/Security
- Using Other Functions
- Sending a Message
- Leaving an Advisory Message
- Display Number of Waiting Calls and Overload Indication
- Using Another Telephone Like Your Own for a Call
- Change call number (relocate)
- Fax Details and Message on Answering Machine
- Resetting Services and Functions (System-Wide Cancellation for a Telephone)
- Activating Functions for Another Telephone
- Using System Functions from the Outside (DISA: Direct Inward System Access)
- Using functions in ISDN via code dialing (keypad dialing)
- Controlling Connected Computers or Other Programs and Telephone Data Service (NotforHiPath500))
- Controlling Relays (Not forHiPath500)
- Sensors (HiPath3300/3350/3500/3550 Only)
- Radio Paging (Not for U.S., Not for HiPath500)
- Using Other Team Functions
- Team and Executive/Secretary Functions With Trunk Keys
- Using Trunk Keys
- Forwarding Calls on Lines
- Using DSS Keys
- Transferring a Call in Progress
- Accepting a Call for Another Team Member
- Joining or Leaving a Group Call (Not for the Executive Telephone in an Executive/Secretary Team)
- Transferring Calls Directly to the Executive (Only in an Executive/Secretary Group)
- Testing the Telephone
- Special Functions in the LAN (Not for HiPath500)
- Different Displays in a HiPath4000 Environment (NotforHiPath500)
- Labeling, Documentation
- Fixing Problems
- Index
- Overview of Functions/Codes (Alphabetical)
- FCC and Industry Canada Compliance
Making Calls – Basic Functions
17
Step by Step
Making Calls
Off-Hook Dialing
n Lift the handset.
o Internal calls: Enter the station number.
External calls: Enter the external code and the station
number.
The called party does not answer or is busy:
t Replace the handset.
On-Hook Dialing
o Internal calls: Enter the station number.
External calls: Enter the external code and the station
number.
The other party answers with speaker:
n Lift the handset.
or On-hook: Use speakerphone mode (not available with
optiPoint 500 economy and optiPoint 500 basic).
The called party does not answer or is busy:
Press the key. The LED goes out.
Ending the call
t Replace the handset.
or
Press the key.
Speaker
Your system may also be programmed so that
you have to press the Internal key before you dial
an internal number.
To call an external party, you have to enter an ex-
ternal code before dialing the party’s telephone
number (Prime Line is not active; contact your
service personnel).
Release