RWB29 Programmer Daily Programming
RWB29 Controls ON WHEN LIT EXTEND ADVANCE RESET MENU/SELECT UP & DOWN BACK/EXIT
Introduction This booklet gives you easy to follow instructions allowing you to set your RWB29 Programmer to the Daily, (same ON/OFF times each day) program. 1 2 3 4 Contents How do I change/set the ON/OFF times? How do I review the current ON/OFF times? What do the switching options mean? How do I select my Switching Options? 7 How do I set my holiday program? How do I activate my holiday program? What do the buttons do? 8 Notes on RWB29 settings.
RWB29 Daily 3:37 CH OFF PM MAN Mon Tue Wed Thu Fri Sat Sun 10:32 AM 2P MENU At first installation display will show as above unless reset is activated. At first installation display will show as above when reset is activated.
How do I change/set the ON/OFF times? • Press left hand button MENU • Press top middle button until SET PROGRAM is shown Press left hand button SELECT display will show SET CH 3:37 HW CH OFF OFF MAN MAN MENU 3:37 PM SET PROGRAM SELECT EXIT • Press left hand button SELECT display will show 3:37 CH PM 8:30 AM SET 1st SELECT (continued on next page) PM ON BACK
To change 1st ON time for CH press SELECT, time will flash, change times by using +/- , when desired time is in the display press ENTER display will show 12:00 SET THE TIME ENTER +/- BACK 3:37 CH • Repeat as above until last OFF time for CH is entered display will show press middle top button SET HW is shown, repeat as above until all HW times have been entered, press BACK, then press EXIT to return to MENU PM SET 1st SELECT OFF BACK 3:37 CH PM 10:30 AM PM 10:30 AM SET SELECT CH BACK
How do I review the current ON/OFF times? • Press left hand button MENU, press top middle button until REVIEW PROG is shown • Press left hand button SELECT display shows Press VIEW • 1st ON time for Central Heating (CH) will be shown 3:37 HW CH OFF OFF REVIEW PROG SELECT EXIT CH PROGRAM VIEW BACK 10:30 AM CH VIEW (continued on next page) PM MAN MAN 1st ON BACK
• Press top middle button 1st OFF will be shown • Continue above two actions until all times have been reviewed press right hand button BACK, press top middle button .
What do the switching options mean? AUTO This means that the RWB29 will switch ON and OFF according to the programmed times MANUAL OFF This means that the RWB29 will be permanently OFF MANUAL ON This means that the RWB29 will be permanently ON ONCE This means that the RWB29 will switch ON at the first ON time and switch OFF at the last OFF time you have programmed ignoring any ON/OFF times in between. This is also referred to as All Day.
3:37 How do I select my four switching options? PM SET STATUS SELECT EXIT • Press left hand button MENU Display shows • Press left hand button SELECT Display shows CH STATUS SELECT BACK • Press bottom middle button correct selection is displayed (CH, HW or CH+HW) until • Press left hand button SELECT Display shows (continued on next page) MANUAL OFF ENTER BACK
• Press top middle button your switching option is displayed until MANUAL OFF ENTER BACK AUTO* MANUAL OFF* MANUAL ON* ONCE* *see previous page for details • Press left hand button ENTER, repeat for other selections (HW, CH etc) CH+HW STATUS SELECT BACK • Press right hand button BACK • Press right hand button EXIT Display shows 3:37 HW CH OFF OFF MENU PM MAN MAN
How do I set my holiday program? • Press left hand button MENU • Press top middle button until SET HOLIDAY is shown • Press left hand button SELECT display shows number of holiday days will flash, change amount of days (1-99) by using +/- , when desired amount of days is in the display press left hand button ENTER, then right hand button EXIT to return to MENU 3:37 CH OFF PM MAN MENU 3:37 CH OFF PM MAN SET HOLIDAY SELECT EXIT 20 ADJUST DAYS ENTER +/- BACK
How do I activate my holiday program? • Press left hand button MENU SET STATUS is shown, press SELECT • Press top middle button until HOLIDAY is shown • Press left hand button SELECT display will flash as shown your system is now in HOLIDAY mode (OFF) and will countdown the amount of days you have set it for, at the end of which it will automatically go back to your normal set program. You can also press CANCEL to return to normal program mode.
What do the buttons do? ADV (ADVANCE) This brings forward the next switching time, for example:(a) if your times were ON 7am and OFF 9am - ON 5pm and OFF 10pm and you pressed the ADV at 4pm your heating would come ON straight away and go OFF at 10pm. (b) if your times were ON 7am and OFF 9am - ON 5pm and OFF 10pm and you pressed the ADV at 9pm your heating would go OFF straight away and come ON at 7am the next morning.
Notes on RWB29 settings. Your RWB29 comes with the correct day of the week, date and time preset, it will also automatically switch to and from daylight saving hours. Should you at anytime or for any reason need to manually adjust the clock settings, please refer to the following pages.
To manually adjust the clock? • Display shows Press MENU Mon CH 3:37 OFF PM MAN MENU • Press bottom middle button until display shows Press SELECT • Alter time using +/buttons to scroll, when correct time is shown press left hand button ENTER display shows (continued on next page) 12:00 PM SET TIME/DAY SELECT EXIT 12:00 PM SET YR 2006 ENTER +/- BACK
• Alter year using +/buttons, when correct year is shown press left hand button ENTER, display shows • Alter month using +/buttons to scroll, when correct month is shown press left hand button ENTER display shows 12:00 SET MONTH 09 ENTER +/- BACK 12:00 PM SET DAY 09 ENTER +/- BACK Mon • Alter day of the month using +/buttons, when correct day of the month is shown press ENTER then press right hand button EXIT display shows PM CH 3:37 OFF MENU PM MAN
What is a programmer? ... an explanation for householders Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and domestic hot water on and off at the same time, while others allow the domestic hot water and heating to come on and go off at different times. Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle.
