RFID systems SIMATIC RF300 System Manual xx/2020 C79000-G8976-C345-08
Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
Table of contents 1 ............................................................................................................................................................... 5 1.1 1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 1.1.6 1.1.7 1.1.8 1.1.9 1.1.10 1.1.11 1.1.12 SIMATIC RF360R................................................................................................................... 5 Features ............................................................................................................
Table of contents 4 SIMATIC RF300 System Manual, xx/2020, C79000-G8976-C345-08
1 1.1 SIMATIC RF360R 1.1.
1.1 SIMATIC RF360R 1.1.3 Connecting the reader to functional ground You need to connect the reader to functional ground. A ground bore hole is provided for this on the connection side of the reader for attaching a grounding conductor.
1.1 SIMATIC RF360R Figure 1-1 1.1.4 Connecting the grounding conductor Connecting readers Requirement Only wire the communication module when the supply voltage is switched off. Required tools When using preassembled cables, you need the following tool: • Torque wrench set (e.g. from Peres; M12/M8, can be set; PER091) for wiring the reader connections Note Using preassembled cables When connecting the supply voltage, we recommend the cables specified in the section "AUTOHOTSPOT" (4 x 1.
1.1 SIMATIC RF360R Accessories required You need the following accessories: • For connecting the power supply M12 plug (4-pin, L-coded) and 4-wire cable (4 x 1.5 mm2) • for PROFINET IO connection M12 plug (4-pin, D-coded) and 4-wire Ethernet cable (Twisted Pair, shielded) You can find the associated article numbers in the section "AUTOHOTSPOT". Connect the plug Proceed as follows to connect the device: 1. Push the respective plug into the corresponding round socket on the reader.
1.1 SIMATIC RF360R Table 1-3 Pin assignment PROFINET IO; M12 socket (4-pin, D-coded) Pin 1.1.6 Assignment 1 Data line TxP 2 Data line RxP 3 Data line TxN 4 Data line RxN View of M12 socket, 4-pin LED displays Operation LED display The operational states of the reader are displayed by two LEDs.
1.1 SIMATIC RF360R Status LED display (including PROFINET/Ethernet LEDs) The operating states of the reader are displayed by the LEDs "R/S", "ER" and "MAINT". The LEDs can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 1-5 Shows the operating states via the status LED display R/S ER MAINT Meaning The reader is turned off. -- -- • LED test while the reader is starting up. • The reader is manually reset to factory settings. • A connected cable is defective.
1.1 SIMATIC RF360R 1.1.8 Metal-free area D The RF360R can be flush-mounted in metal. Allow for a possible reduction in the field data. To avoid any influence on the field data, the distance "a" should be kept to.
1.1 SIMATIC RF360R 1.1.
1.1 SIMATIC RF360R Figure 1-4 1.1.10 Face-to-face distance between two RF360R Technical specifications Table 1-7 Technical specifications of the RF360R reader 6GT2801-5BA30 Product type designation SIMATIC RF360R Radio frequencies Operating frequency, rated value 13.
1.1 SIMATIC RF360R 6GT2801-5BA30 Enclosure • Material • Plastic PA 12 • Color • TI-Grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 150 mA Permitted ambient conditions Ambient temperature • During operation • 0 … +55 °C • During transportation and storage • -40 … +70 °C Degree of protection according to EN 60529 IP67 Shock-resistant acc.
1.1 SIMATIC RF360R (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1.1 SIMATIC RF360R Dimension drawing 1.1.
