User Manual

ManualsBrandsSiemens ManualsThermostats (temperature controller with sensor)RDY2000 Commercial Room Thermostat Installation Instructions

Installation Instructions

Document No. 129-905

February 6, 2018

Spanish Version

RDY2000 Commercial

Room Thermostat

Item Number 129-905, Rev. GA Page 1 of 18

Para accede al documento en Español, escanee el código QR que se encuentra en la parte trasera del termostato.

Figure 1. RDY2000 Thermostat.

Product Specifications

System Compatibility

Conventional Up to 3 Heating/3 Cooling stages

Heat Pumps Up to 4 Heating/2 Cooling stages

Electrical Characteristics

Power Supply 24 Vac +/-20%, Class 2, 4A max.

Power Usage 4 VA (maximum)

Output Relay

Ratings

Pilot duty, 1A max. per output, 4A

max total

Ambient Limitations

Operating

Temperature

23°F to 122°F (-5°C to 50°C)

Storage/Shipping

Temperature

-13°F to 158°F (-25°C to 70°C)

Relative Humidity Up to 95% (non-condensing)

Enclosure

Rating NEMA 1

NOTE: The RDY2000 is not battery-powered. It

requires 24 Vac power from the HVAC

equipment at terminals RH/RC and C.

Product Number

RDY2000

Caution Notations

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools

• No. 1 Phillips screwdriver

• 1/8” flat-blade screwdriver

• Drill with 1/8" drill bit

Expected Installation Time

15 minutes

CAUTION:

The RDY2000 is an advanced controller

designed to be installed by professional

HVAC technicians. Installation by non-

qualified personnel may result in degraded

system efficiency, occupant discomfort, or

equipment damage.

Prerequisites

• All work must be performed in accordance

with applicable codes and standards.

• Use 18 gauge thermostat wire for equipment

connections.

• 22 gauge shielded cable is recommended

for remote sensor wiring. Do not exceed 150

feet.

• To replace an existing thermostat, verify if

24 Vac is present between the RH/RC and

C terminals.

• Turn off power to the HVAC equipment

before attempting to remove the existing

thermostat.

• Record wiring connections to existing

thermostat terminals.

• Remove the existing thermostat before

proceeding.

Installation

1. Install the thermostat base plate.

a. Feed the existing wires through the opening

in the base plate.

Summary of content (18 pages)

PAGE 1
Installation Instructions Document No. 129-905 February 6, 2018 Spanish Version RDY2000 Commercial Room Thermostat Required Tools • • • No. 1 Phillips screwdriver 1/8” flat-blade screwdriver Drill with 1/8" drill bit Expected Installation Time 15 minutes CAUTION: The RDY2000 is an advanced controller designed to be installed by professional HVAC technicians. Installation by nonqualified personnel may result in degraded system efficiency, occupant discomfort, or equipment damage. Figure 1.
PAGE 2
Document No. 129-905 Installation Instructions February 6, 2018 b. Secure the base plate to the mounting surface using supplied hardware. NOTE: Ensure that the UP arrows embossed on the base plate are pointed upward. 6. Secure the thermostat to the base plate with the Phillips screws (provided), using the holes at the bottom of the housing. The installation is now complete. Restore power, and continue to Thermostat Setup. Thermostat Setup Figure 2. Thermostat Base Plate.
PAGE 3
Document No. 129-905 Installation Instructions February 6, 2018 Status Bar Service Reminders and Fault Messages The status bar at the top of the display consists of 11 icons. • Table 2. Status Bar Icons. Icon Name Occupied Keypad Lock Scheduler Override Humidity Control Indicator Fan Fresh Air Cool Mode Heat Mode Heating/Cooling Stages Auxiliary Heating Siemens Industry, Inc. Meaning Space is occupied, based on Schedule and/or Occupancy Sensor. Keypad is locked.
PAGE 4
Document No. 129-905 Installation Instructions February 6, 2018 Wiring Diagrams Figure 4. Wiring Schematic, Conventional System. Page 4 of 18 Siemens Industry, Inc.
PAGE 5
Document No. 129-905 Installation Instructions February 6, 2018 Figure 5. Wiring Schematic, Heat Pump. Figure 6. Wiring Schematic, Aux Output 3. Siemens Industry, Inc.
PAGE 6
Document No. 129-905 Installation Instructions February 6, 2018 NOTE: If the screen is not touched for 10 seconds, the unit returns to the Home screen. Set-up Wizard When the unit is powered up for the first time, WIZARD displays. This tool is used to program the basic system parameters. Additional parameters can be accessed directly via the Installer/Expert Set-up menus. NOTE: The thermostat will not start the control sequence until the Set-up Wizard is complete. 1. Press WIZARD to access the menu. 2.
PAGE 7
Document No. 129-905 Installation Instructions February 6, 2018 Programming the Schedule 1. Touch the center of the Home screen. 4. Using the lower left [ï] and right [ð] arrows, enter the INSTALLER password. 2. Press the Settings [ displays. 5. Press PASSWORD to accept the password. 6. Set Parameter 211 (Keypad Lockout) to zero to disable keypad lockout. 4. Use the left [ï] and right [ð] arrows to select the day. Press the day to select. 7.
PAGE 8
Document No. 129-905 Installation Instructions February 6, 2018 Table 3. 100 Series Parameters*. Parameter Definition Display Value Range Default CO HP CO Extended Definition Notes CO = Conventional System HP = Heat Pump P101 System Type SYS TYPE P102 Cooling Stages COOL STGS 0 1 2 3 2 Sets number of cooling stages. P103 Heating Stages HEAT STGS 0 1 2 3 2 Sets number of heating stages.
PAGE 9
Document No. 129-905 Installation Instructions February 6, 2018 Table 4. 200 Series Parameters. Parameter Definition Display Value Range Default P201 Heat Temp Limit HEAT LIMIT P202 Cool Temp Limit COOL LIMIT P203 Temperature Display Offset TMP OFFSET 45°F to 95°F (7.0°C to 35.0°C) 50°F to 95°F (10.0°C to 35.0°C) -5°F to 5°F (-3.0°C to 3. 0°C) 95°F (35.0°C) Sets maximum allowable heating set point. Does not appear if P103 = 0. 50°F (10.0°C) Sets minimum allowable cooling set point.
PAGE 10
Document No. 129-905 Installation Instructions February 6, 2018 Table 5. 300 Series Parameters.
PAGE 11
Document No. 129-905 Installation Instructions February 6, 2018 Parameter Definition Display P311 Temperature Input 3 Low TMP 3 LO P312 Temperature Input 3 High TMP 3 HI P313 Configurable Input 4 (IN4) INPUT 4 P314 Temperature Input 4 Type TMP IN 4 P315 Temperature Input 4 Low TMP 4 LO P316 Temperature Input 4 High TMP 4 HI P317 Aux Output 1 (OUT1) P318 Aux Output 2 (OUT2) P319 Aux Output 3 (OUT3 & C3) P320 Independent Humidity Control Siemens Industry, Inc.
PAGE 12
Document No. 129-905 Installation Instructions February 6, 2018 Table 6. 400 Series Parameters. Parameter Definition Display Value Range Default P401 Unit Number UNIT NMBR 1 to 999 --- Allows HVAC unit number to be displayed on thermostat home screen. CO2 SET PT 500 to 2000 PPM 800 If CO2 level, as measured by an external sensor exceeds setpoint, the Ventilation sequence is initiated.
PAGE 13
Document No. 129-905 Installation Instructions February 6, 2018 Table 7. 500 Series Expert Settings Parameters. (Only available if logged in as an Expert.) NOTE: P500 Series parameters are factory-set for optimum system performance. Changing these settings may degrade efficiency and/or compromise occupant comfort. Parameter Definition Display Value Range Default P501 Stage Delay - Cooling STG DLY CL 1 to 10 minutes 2 P502 Stage Differential - Cooling STG DIF CL 1°F (0.5°C) to 10°F (5.
PAGE 14
Document No. 129-905 Installation Instructions February 6, 2018 Table 8. 900 Series Expert Settings Parameters. (Only available if logged in as an Expert.) CAUTION: P900 Series parameters are used by professional HVAC technicians during the system commissioning process. Interlocks and time delays are defeated while using P900 parameters. Use of these parameters by non-qualified personnel may result in equipment damage.
PAGE 15
Document No. 129-905 Installation Instructions February 6, 2018 Dehumidification Parameters • • • P317/ P318/P319: One of these must be set to 2 P320: NO (default) = Dehumidification will only occur if there is a call for cooling. YES = Dehumidification relay will be energized independently of heating and cooling relays. Dehumidity Setpoint: User adjustable to desired level in dehumidification mode. Sensors: Onboard humidity sensor or optional remote humidity sensor.
PAGE 16
Document No. 129-905 Installation Instructions February 6, 2018 Table 9. Single Schedule. Day 2 Periods Per Day Phase Setpoint Heat, °F Setpoint Cool,°F Time NOTE: 4 Periods Per Day Day Night Wake Day Evng Night 70 62 70 62 70 62 75 6:00 AM 82 10:00 PM 75 6:00 AM 78 11:00 AM 75 1:00 PM 82 10:00 PM Daily Schedule – 2 periods per day: Parameter 107 = 1; Parameter 108 = 2 Daily Schedule – 4 periods per day: Parameter 107 = 1; Parameter 108 = 4; Parameter 109 = F Table 10.
PAGE 17
Document No. 129-905 Installation Instructions February 6, 2018 Table 13. Individual Days (Monday – Sunday). Day Phase Setpoint Heat Setpoint Cool Time 2 Periods Per Day Day 70 75 6:00 AM 4 Periods Per Day Night 62 82 10:00 PM Wake 70 75 6:00 AM Day 62 78 11:00 AM Evng 70 75 1:00 PM Night 62 82 10:00 PM NOTE: Daily Schedule – 2 periods per day: Parameter 107 = 7; Parameter 108 = 2; Parameter 109 = F Daily Schedule – 4 periods per day: Parameter 107 = 7; Parameter 108 = 4; Parameter 109 = F Table 14.
PAGE 18
Table 15. Record Field Settings.