Basic Documentation
Table Of Contents
- 1 About this document
- 2 Overview
- 3 Notes
- 4 Functions
- 4.1 Temperature control
- 4.2 Operating modes
- 4.3 Room temperature setpoints
- 4.4 Application overview
- 4.5 Power supply selection for RDG200KN
- 4.6 Additional functions
- 4.7 Control sequences
- 4.7.1 Sequence overview (setting via P001)
- 4.7.2 Application mode
- 4.7.3 2-pipe fan coil unit
- 4.7.4 2-pipe fan coil unit with electric heater
- 4.7.5 2-pipe fan coil unit with radiator or floor heating
- 4.7.6 2-stage heating and cooling
- 4.7.7 4-pipe fan coil unit
- 4.7.8 4-pipe fan coil unit with electric heater
- 4.7.9 Chilled/heated ceiling and radiator applications
- 4.7.10 Compressor applications
- 4.7.11 Applications with external AQR sensor or QMX room operator unit
- 4.7.12 Setpoints and sequences
- 4.8 Control outputs
- 4.9 Fan control
- 4.10 Multifunctional input, digital input
- 4.11 Handling system faults
- 4.12 KNX communications
- 4.12.1 S-Mode
- 4.12.2 Master/slave configuration in KNX S-Mode
- 4.12.3 LTE-Mode
- 4.12.4 Zone addressing in LTE-Mode (with Synco)
- 4.12.5 Master/slave configuration in LTE-Mode
- 4.12.6 Example of heating and cooling demand zones
- 4.12.7 Send heartbeat and receive timeout
- 4.12.8 Startup
- 4.12.9 Heating and cooling demand
- 4.12.10 Fault and alarms function on KNX
- 4.13 Communication objects
- 4.14 Communication objects (LTE-Mode)
- 4.15 Control parameters
- 5 Supported KNX tools
- 6 Connection
- 7 Technical data
- 8 Dimensions
- Index
Index
168 | 170
A6V11545892_en--_b
KNX overview ..............................................107
KNX parameters ..........................................137
KNX S-Mode ................................................107
KNX tools ....................................................136
L
Local time of day .......................................... 60
LTE-Mode....................................................111
M
Manual heating/cooling changeover ................... 47
Manually select heating or cooling sequence .. 67
Master/slave ................................................. 62
Minimum output ............................................. 48
Moisture........................................................ 66
Monitoring with ACS ....................................142
Monitoring with OZW772 ..............................146
Multifunctional input ....................................104
N
NFC ............................................................. 66
O
On/Off control signal ..................................... 91
Operation with ACS .....................................142
Operation with OZW772 ................................146
OZW772 ......................................................146
P
Parallel connection of switches ....................106
Parameter setting in ACS .............................140
Parameter setting in ETS ..............................137
Parameter setting via tool .............................127
Parameter settings in ACS ............................142
Plant diagram in ACS ...................................143
Presence detector .......................................... 30
Purge function................................................ 48
PWM ............................................................ 91
PWM for electric heater ................................... 93
R
Radiator applications .................................... 85
Remote heating/cooling changeover .................. 46
Remote operation ........................................146
Reset parameters ..........................................126
Return flow temperature control ........................ 53
Room humidity ............................................... 57
S
Scheduler...................................................... 60
Sensor input................................................104
Setpoint Comfort mode ................................. 90
Setpoint Economy mode ............................... 90
Setpoint high ................................................. 57
Setpoint low ................................................... 57
Setpoint priority .............................................. 39
Setpoint Protection mode .............................. 90
Setpoints - setting via bus ............................. 36
Setpoints and sequences .............................. 90
S-Mode .......................................................107
Supply air temperature limitation ....................... 51
Swap function ........................................... 48, 52
Switching off external equipment ....................... 50
Synchronization ............................................. 93
Synco 700 ..................................................... 15
T
Temperature out of range ...............................107
Temporary comfort setpoint .............................. 35
Time of day via bus ......................................... 60
Tool - Parameter setting and download..........127
V
Valve kick/exercising ....................................... 53
W
Window contact ...........................................104
Z
Zone addressing ..........................................111
Δ
ΔT control .................................................... 53










