Flush-mounted sensors and room operator units for KNX PL-Link QMX3.P35H..., QMX3.P38H... Communicating sensors, switches and room operator units with KNX PL-Link (for Desigo™ Room Automation) Functions (depending on type) ● 160 x 128 pixel touch screen ● Energy efficiency function (“Green Leaf”) ● Built-in room temperature sensor ● LCD display for room temperature, CO2, humidity, PM2.5, operating mode etc. ● User interface for lighting, blinds and scene control (QMX3.
Use / compatibility The room automation station determines the functions of both LCD display and touch screen. ● Measure and indicate the room temperature ● Display humidity, PM2.5, and CO2 ● Operate room functions ● Indicate external information (outdoor temperature, outdoor humidity) Mechanical design ● ● ● ● The devices are designed for a common conduit box (A). – Conduit box: Keep in mind the dimensions of the conduit box! The base plate (B) has screw holes for all common conduit boxes (A).
Notes Security CAUTION National safety regulations Failure to comply with national safety regulations may result in personal injury and property damage. ● Observe national provisions and comply with the appropriate safety regulations. Engineering ● ● ● ● ● ● The room operator units offer plug & play functionality. The room operator units receive power from the connected room automation station via the KNX PL-Link interface.
● Do not interchange the wires of the KNX PL-Link cable. – The red terminal is for KNX PL-Link + – The gray terminal is for KNX PL-Link – ● Observe all local installation regulations. CAUTION! The devices are not protected against accidental connection to AC 230 V. Operation Operational setting NOTICE Operation and display oft he room operator unit depend on the control program of the room automation station. Main page displaying HVAC functions for all types (QMX3.P35H…, QMX3.
Example Icon Description Inside and outside temperature Temperature display in ℃ or ℉, humidity display in % r.h., CO2 display in ppm, PM2.
Main page displaying lighting, blinds and scenes (QMX3.P38H, QMX3.
Icon Description Service Sleep Brighter Softer Change the blinds angle HVAC operation, identical with QMX3.P35H (touch this icon to go to the HVAC home page) Manual commissioning (KNX PL-Link) All commissioning work is done via the room automation station, using SSA-DNT or ABT. ABT is never connected directly to a room operator unit. When more than one QMX3.P... room operator unit is on the same trunk of the KNX PL-Link bus, manual commissioning is as follows: 1.
Maintenance NOTICE The device can be cleaned with off-the shelf, solvent-free cleaning agents. Do not use mechanical aids (rough sponge or similar materials) – only a soft, damp cloth. Disposal The device is considered an electronic device for disposal in accordance with the European Guidelines and may not be disposed of as domestic garbage. ● Dispose of the device through channels provided for this purpose. ● Comply with all local and currently applicable laws and regulations.
Technical data Power supply Operating voltage KNX / PL-Link DC 21...30 V 1) Power QMX3.P35H consumption QMX3.P35H-BSC (room automation QMX3.P38H station) QMX3.P38H-BSC Max. 15 mA at DC 24 V Max. 15 mA at DC 24 V Max. 15 mA at DC 24 V Max. 15 mA at DC 24 V 1) The device receives power from the connected room automation station via the KNX / PLLink interface. Operating data Temperature sensor (all types) Measuring element NTC resistance sensor Measuring range 0…50 °C Measuring accuracy(5…30 °C) < 0.
Ambient conditions and protection classification Protection standard as per EN 60529 IP30 Insulation protection class III Climatic ambient conditions ● Storage as per EN 60721-3-1 ● ● Transport (packaged for transport) as per ● EN 60721-3-2 ● Operation as per EN 60721-3-3 Mechanical ambient conditions Storage as per EN 60721-3-1 Transport as per EN 60721-3-2 Operation as per EN 60721-3-3 ● Class 1K3 Temperature: -5…45 °C Humidity: 5…95 % r.h. Class 2K3 Temperature: -25...
Diagrams Connection diagrams R1 N1 QMX3... room operator unit Controller, actuator = Twisted pair KNX / PL-Link plug + Red KNX PL-Link (positive) - Gray KNX PL-Link (negative) NOTICE ● ● Wires are NOT interchangeable. The device is protected against faulty wiring, and communications do not work on interchanged wires. Do not connect the KNX / KNX PL-Link bus to the tool plug, only the tool.
Dimensions Dimensions in mm Issued by Siemens Switzerland Ltd Smart Infrastructure Global Headquarters Theilerstrasse 1a CH-6300 Zug Tel. +41 58 724 2424 www.siemens.com/buildingtechnologies 12 Siemens Smart Infrastructure Document ID A6V11521633_en--_b Edition 2020-11-09 © Siemens Switzerland Ltd, 2020 Technical specifications and availability subject to change without notice.
