Duct Temperature, Humidity and Air Quality Sensors: - QAM2151.040/MO - QFM2150/MO, QFM3150/MO - QPM2102/MO, QPM2150/MO, QPM2152/MO Immersion Temperature Sensor: - QAE2154.
Table of Contents 2 | 16 1 1.1 1.2 About this document ............................................................................. 3 Revision history ...........................................................................................3 Before you start ...........................................................................................3 2 2.1 2.2 Product overview ................................................................................. 5 Type summary.............................
About this document 1 Revision history 1 About this document 1.1 Revision history Edition Date Changes Section a 2019-07 First version. All 1.2 Before you start Copyright This document may be duplicated and distributed only with the expressed permission of Siemens Switzerland Ltd. Quality assurance These documents were prepared with great care. ● The content of all documents is checked at regular intervals. ● All necessary corrections are included in subsequent versions.
1 About this document Before you start ● ● 4 | 16 From your Siemens branch office www.siemens.com/sbt or at your system suppliers. From the support team at headquarters fieldsupport-zug.ch.sbt@siemens.com if no local POC is available. Siemens assumes no liability to the extent allowed under the law for any losses resulting from a failure to comply with the aforementioned points or for the improper compliance of the same.
Product overview Type summary 2 2 Product overview The sensors are used in ventilation and air conditioning plants. 2.1 Type summary Product number SSN no. Measurement parameter CO2 IAQ (VOC) Temperature Relative humidity Output signal QAE2154.010/MO S55720S465 - - -10...120 °C - Modbus RTU QAM2151.040/MO S55720S466 - - -50…50 °C - Modbus RTU QFM2150/MO S55720S467 - - -40…70 °C 0…100 % r.h. Modbus RTU QFM3150/MO S55720S468 - - -40…70 °C 0…100 % r.h.
3 Wiring 3 Wiring 6 | 16 G Operating voltage AC 24 V ±20 % or DC 13.5...
Configurations DIP switch for configuration method selection 4 4 Configurations 4.1 DIP switch for configuration method selection The sensor is a Modbus RTU (RS-485) slave device. It can be configured with a Modbus master when DIP2-Position 7 is OFF (default setting). The sensor has two sets of DIP switches: DIP1 and DIP2. It can be manually configured with DIP switches when DIP2-Position 7 is ON. For details, see DIP switch configuration [➙ 12]. 4.
4 Configurations Modbus registers NOTES: ● Register 764 (Modbus address) cannot be configured as 246 via a master. Address 246 is reserved for on-event addressing. ● Bus configuration command (768) is for on-event addressing only. 4.3 Modbus registers Holding Register (16-bit) No. Description Range Unit Scaling Default R/W 1 Temperature value -327…327 °C °C 0.01 - R -556.6…620.6 °F °F Temperature reliability 0 – No error - - - R 3 Relative humidity value 0…100 % % 0.
Configurations LED colors and patterns Holding Register (16-bit) No.
4 Configurations Push button configuration 4.5 Push button configuration When DIP2-Position 7 is OFF (default setting), push button function is activated. Push button The following can be operated via push button: ● On-event addressing ● Resetting the Modbus parameters to factory default settings 4.5.1 On-event addressing (ClimatixTM controllers configuration) On-event addressing is a rapid configuration approach working together with Siemens ClimatixTM controllers.
Configurations 4 Push button configuration NOTES: 1) The master cannot change the Modbus address (register 764) to 246. 2) The interval between every configuration command for register 764…768 from ClimatixTM is not more than 30 s. If it exceeds 30 s, the addressing mode ends automatically. 3) 10-minute countdown starts from entering addressing mode. 4.5.
4 Configurations DIP switch configuration 4.6 DIP switch configuration The Modbus setting can be configured via DIP switches when DIP2-position 7 is ON. NOTICE Modbus registers 764…768 are not writable via a master under DIP switches configuration. The sensor has two sets of DIP switches: DIP1 and DIP2.
Configurations Bus termination 4 DIP2 Baud rate, transmission format, configuration Baud rate Parity Stop bit Configuration Function 1) 1 2 3 4 5 6 7 OFF OFF OFF 0 = Auto OFF OFF ON 1 = 9600 OFF ON OFF 2 = 19200 OFF ON ON 3 = 38400 ON OFF OFF 4 = 57600 ON OFF ON 5 = 76800 ON ON OFF 6 = 115200 ON ON ON others = Auto OFF OFF 0 = Even (default) OFF ON 1 = Odd ON OFF 2 = No parity ON ON others = Even OFF 1 (default) ON 2 OFF Configurable via master or p
5 Maintenance Disposal 5 Maintenance 5.1 Disposal The device is considered electrical and electronic equipment for disposal in terms of the applicable European Directive and may not be disposed of as domestic garbage. 14 | 16 ● Dispose of the device through channels provided for this purpose. ● Comply with all local and currently applicable laws and regulations.
Appendices Cyber security disclaimer 6 6 Appendices 6.1 Cyber security disclaimer Products, solutions and services from Siemens include security functions to ensure the secure operation of building automation and control, fire safety, security management, and physical security systems. The security functions on these products, solutions and services are important components of a comprehensive security concept.
Issued by Siemens Switzerland Ltd Smart Infrastructure Global Headquarters Theilerstrasse 1a CH-6300 Zug +41 58 724 2424 www.siemens.com/buildingtechnologies A6V11610643_en--_a © Siemens Switzerland Ltd, 2019 Technical specifications and availability subject to change without notice.
