User Manual
Table Of Contents
- 1 About this document
- 2 Commissioning
- 2.1 Default connection
- 2.2 Initial login
- 2.3 Setup wizard
- 2.4 Discover and assign devices
- 2.5 Subscribing to the time master
- 2.6 Time synchronization of the time master
- 2.7 Registering as a foreign device
- 2.8 Touch panel settings
- 2.9 Operating and monitoring features
- 3 Data point integration
- 4 Graphic features
- 4.1 Plant view Tools
- 4.2 Kiosk graphics
- 4.3 Engineering notations
- 5 Graphics Builder
- 5.1 Overview
- 5.2 Pane tools
- 5.3 Graphics libraries
- 6 Graphics engineering
- 6.1 Using supersample graphics
- 6.2 Optimizing graphics for PXM touch panels and standard devices
- 6.3 Thumbnails
- 6.4 Dashboards
- 7 Advanced functionality
- 8 Tips and tricks
- 8.1 Updates required after a time zone change
- 8.2 APPLY BATCH TAGS
- 8.3 Graphic components within models cannot be modified
- 8.4 A graphic with relative binding that includes data points from different branches of the hierarchy cannot be created at the Root level
- 8.5 Relative hyperlinks cannot be added to a graphic at the Root level
- 8.6 Relative hyperlinks in a graphic are broken if the graphic is engineered offline and then imported to another device
- 8.7 Automatic logout from Desigo Control Point causes Graphics Builder to temporarily stop working
- 8.8 Detection of network interruptions
- 8.9 Cancelling a kiosk log out sequence
- 8.10 Special characters do not display in graphic file names
- 8.11 The color of a graphical component may display incorrectly if the component was copied
- Index
Graphics Builder
Graphics libraries
5
140 | 195
A6V11604297_en--_g
5.3.1.1 Pre-loaded supersample graphics library
This section outlines the graphics that are pre-loaded in Desigo Control Point devices.
Graphic type
Characteristics
Primary supersample
● Use with PXC4/5 controllers:
– Datapoint binding must be redone.
– Relativization to be done by shortName.
● Use with BACnet standard devices:
– Datapoint binding must be redone.
– Relativization to be done by navName. See Using Relative by navName binding [➙ 64].
Application example
● Relativized example graphic compatible with Desigo primary controllers PXC4/5, engineered with ABT
Site.
– Relativization done by shortName.
– Example graphic compatible with the PXC4/5 application program examples.
– Manual rework required to match the example graphic with the project specific application program.
Dashboard template
● Template graphic for energy dashboards.
– Additional engineering effort per project required.
– Use with BACnet standard devices must be tested individually.
Table 64: Properties of pre-loaded graphics.
Supersample graphic name
Style
Description
Sample AHU_ERCPL_HC_HUM_H_TPH
2D+ / 2D*
AHU; ERC (plate); heating and cooling; humidifier; humidity, temperature and
pressure control
Sample AHU_ERCRnacl_HC_TP
2D+ / 2D*
AHU; ERC (run around coil); heating and cooling; temperature and pressure
control
Sample AHU_ERC_HC_TP
2D+ / 2D*
AHU; ERC (rotary); heating and cooling; temperature and pressure control
Sample AHU_ERC_H_TP
2D+ / 2D*
AHU; ERC (rotary); heating only; temperature and pressure control
Sample AHU_MIX_HC_TP
2D+ / 2D*
AHU; ERC (mixing circuit); heating and cooling; temperature and pressure
control
Sample CGEN_1Ch
2D+ / 2D*
Cooling generation: one chiller
Sample CGRP_1Grp
2D+ / 2D*
Cooling group: one group
Sample CGrp_1Grp_Pu
2D+ / 2D*
Cooling group: one group with mixing circuit
Sample Dhw_DhwHyd
2D+ / 2D*
Domestic hot water: with hydraulic charge
Sample HGEN_1Bo
2D+ / 2D*
Heat generation: one boiler
Sample HGEN_2Bo
2D+ / 2D*
Heat generation: two boilers
Sample HGRP_1GRP
2D+ / 2D*
Heat generation: one group
Sample HGRP_1GrpPu
2D+ / 2D*
Heat generation: one group with mixing circuit
Sample Heating Curve
–
Calculates the flow temperature setpoint based on outside air temperature,
room setpoint and other factors, such as wind and solar.
Table 65: Primary supersample graphics.
*
The 2D style graphics with _PXM40_ in the graphic name are optimized for use with PXM40... These graphics have a fixed resolution
and sharper data point text, the option Scale to Fit is disabled, and they will load without rescaling.