User Manual

ManualsBrandsSiemens ManualsBuilding automationBACnet router for BACnet/IP, BACnet/LonTalk, BACnet MS/TP PXG3.L, PXG3.M

CM1N9270en_10

2017

-10-16

Building Technologies

270

Desigo™ PX

BACnet router for

• BACnet/IP

• BACnet/LonTalk

• BACnet MS/TP

PXG3.L

PXG3.M

• Routing between BACnet/IP , BACnet/LonTalk (PXG3.L only),

and BACnet MS/TP

• Supports BACnet/IPv4 and BACnet/IPv6

• ANSI/ASHRAE 135-2012 Annex J compliant

• ISO 16484-5 compliant

• BTL label (BACnet communications passed the BTL test)

• BBMD support (BACnet Broadcast Management Device)

• Third-party device support

• Configuration via Xworks Plus or Web browser (via IPv4)

• Web browser access to network statistics

• Firmware update via Ethernet and USB Device

• LED indication for Ethernet link and activity

• LED indication for BACnet/LonTalk and BACnet MS/TP (diagnostics)

• 2-port Ethernet switch for low-cost cabling (10/100 baseT)

• BACnet MS/TP (RS-485) baud rates: 9600, 19200, 38400, 76800, 115200

• Plug-in screw terminal blocks for supply, LONWORKS, and MS/TP

• RJ45 plug for PXM20 (LONWORKS)

• Operating voltage: AC 24 V or DC 24 V

• DIN rail mounting

• BACnet MS/TP Slave Proxy

• SNMP (v2), MIB-2

• BACnet NAT

Summary of content (10 pages)

PAGE 1
9 s 270 Desigo™ PX BACnet router for • BACnet/IP • BACnet/LonTalk • BACnet MS/TP • • • • • • • • • • • • • • • • • • • • • CM1N9270en_10 2017-10-16 PXG3.L PXG3.M Routing between BACnet/IP , BACnet/LonTalk (PXG3.
PAGE 2
Use The PXG3... BACnet router connects a BACnet/IP network to a BACnet/LonTalk network (PXG3.L only), and/or a BACnet MS/TP channel. BACnet objects are transmitted simultaneously throughout any and all networks. Router functions Four-way routing The PXG3... BACnet router transmits BACnet protocol between a BACnet/IPv4 network, a BACnet/IPv6 network, a BACnet/LonTalk network (PXG3.L only), and a BACnet MS/TP channel. BACnet objects are simultaneously transmitted thoughout any and all networks.
PAGE 3
Communication • The router complies with ANSI/ASHRAE 135-2012 Annex J and ISO 16484-5. • A 2-port Ethernet switch allows low-cost cabling via line topology. This is the preferred commissioning medium. • The LONW ORKS network is connected via a 2-pin connection terminal. • The MS/TP channel is connected via RS485 or a 3-pin connection terminal. • An RJ45 plug on the device front allows connecting to a PXM20 operator unit (PXG3.L only). • A USB port is available for connecting the tool.
PAGE 4
LEDs HMI/Tool LED RUN Color Green RUN FLT FLT Red INF COM1 COM2 -Yellow Yellow SVC Red Ethernet Green 1/2 Yellow 9270Z05 87654321 *) Activity • Continuously ON • Continuously OFF • • • • -• • • • • • • • • • • Flashing Continuously OFF Continuously ON Flashing Flashing Flashing Continuously OFF Continuously ON Flashing Flashing per wink command *) Continuously ON Continuously OFF Flashing Continuously ON Continuously OFF Function • Device ready.
PAGE 5
Engineering • The router does not require programming. It is configured either using Xworks Plus or the Desigo SSA-DNT via Ethernet or using a USB device. For details see SSA (Setup & Service Assistant) Commissioning, CA111050). • Each device has a unique identification number to ensure efficient commissioning. The number is located on a removable barcode label. • Each device has a unique MAC address. For more details see document “Ethernet, TCP/IP, MS/TP and BACnet - Principles” (CM110666).
PAGE 6
Technical data Operating voltage ) (24 V~, ⊥, Operating voltage AC 24 V ± 20 % (SELV/PELV) or AC/DC 24 V class 2 (US) 48...63 Hz Symmetric Half-wave load = Technical ground Power consumption Hardware information Response to power / communication failure Ethernet interface HMI interface USB interface LONW ORKS interface (PXG3.L only MS/TP interface Connection terminals, plug-in At AC 24 V At DC 24 V Max. permissible transit power AC/DC 24 V (RJ45 interface, HMI) Internal fuse Processor Max.
PAGE 7
Assignment as per EN 60730 Operation of automatic controller Degree of pollution Design type Housing protection standard Protection type as per EN 60529 Front parts in the DIN section Terminal part Ambient conditions Operation Climatic conditions Temperature Humidity Mechanical conditions Transport Climatic conditions Temperature Humidity Mechanical conditions Standards, directives, and approvals Product standard EN 60730-1 Product family standard EN 50491-x Type 1 2 Protection class III IP30 IP2
PAGE 8
Connection terminals and interfaces 9270z04 HMI 1, 2 2 x RJ45 interface for Ethernet 3 5 24 V ~, ⊥, CLA, CLB +, –, HMI USB Service 87654321 Operating voltage pin assignment LONWORKS pin assignment MSTP pin assignment 9215Z01 RJ45 pin assignment for HMI AC / DC 24 V operating voltage LONW ORKS interface (PXG3.L only) MS/TP interface RJ45 interface for HMI (PXG3.
PAGE 9
Dimensions 9270M01 All dimensions in mm 9 / 10 Siemens Building Technologies PXG3...
PAGE 10
Published by: Siemens Switzerland Ltd. Building Technologies Division International Headquarters Gubelstrasse 22 6301 Zug Switzerland Tel. +41 41-724 24 24 www.siemens.com/buildingtechnologies © Siemens Switzerland Ltd 2012 Delivery and technical specifications subject to change 10 / 10 Siemens Building Technologies PXG3...