Installation Instructions

ManualsBrandsSiemens ManualsBuilding automationMS/TP Point Pickup Modules Installation Instructions

Table Of Contents

Document No. 550-992

August 20, 2014

MS/TP Point Pickup Modules

Rev. BA Page 1 of 6

Figure 1. MS/TP Point Pickup Module.

Product Description

The Siemens MS/TP Point Pickup Module (PPM) is

a BACnet Application Specific Controller that

communicates on a BACnet MS/TP network. The

PPM extends the host BACnet Building Controllers

control program for local or distributed point

expansion.

The MTSP Point Pickup Module Family includes 6

point analog, 6 point digital and 12 point combination

module options with a wide range of sensor type

support.

Product Numbers

Digital PPM-1U32.BPF (1 Universal Input, 3DI,

2DO, fixed terminal blocks)

Digital PPM-1U32.BPR (1 Universal Input, 3DI,

2DO, removable terminal blocks and manual

override switches for commissioning checkout)

Analog PPM-2U22.BPF (2 Universal Input, 2AO,

2AI, fixed terminal blocks)

Analog PPM-2U22.BPR (2 Universal Input, 2AO,

2AI, removable terminal blocks)

Combination PPM-2U3322.BPF (2 Universal Input,

3DI, 3DO, 2AO, 2AI, fixed terminal blocks)

Combination PPM-2U3322.BPR (2 Universal Input,

3DI, 3DO, 2AO, 2AI, removable terminal blocks)

Combination PPM-3U63.BPR (for China only)

(3 Universal Input, 6DI, 3DO, removable terminal

blocks)

Caution Notations

CAUTION:

Equipment damage, or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools

• Small flat-blade screwdriver 0.11” (3-mm)

• Small Phillips screwdriver 0.15" (4-mm)

• Cordless drill/driver set

• Pliers

• Permanent marker or label maker

Expected Installation Time

Average installation time is 15 minutes. This will vary

depending on the device and IO counts.

Prerequisites

• Wiring conforms to NEC and local codes

and regulations. For more information, refer

to the Wiring Guidelines manual (125-3002).

• 24 Vac Class 2 power source available.

• Supply power to the device is OFF.

• Any application specific hardware or devices

are installed.

Summary of content (6 pages)

PAGE 1
Installation Instructions Document No. 550-992 August 20, 2014 MS/TP Point Pickup Modules Caution Notations CAUTION: Equipment damage, or loss of data may occur if you do not follow the procedures as specified. Required Tools Figure 1. MS/TP Point Pickup Module. • Small flat-blade screwdriver 0.11” (3-mm) • Small Phillips screwdriver 0.
PAGE 2
Document No. 550-992 Installation Instructions August 20, 2014 Installation 3. Remove the printed circuit board (PCB) by removing the screw attaching the PCB to the housing. Once the screw is removed, gently lift the lower edge of the board (closest to the screw) up and slide downward, to disengage the top portion of the PCB from the retaining clips. Figure 2. Back plate knockout holes. 1. Bottom plate wiring access 2. 100 mm electrical box mounting 3. 4” x 4” electrical box or flat surface mounting 4.
PAGE 3
Document No. 550-992 Installation Instructions August 20, 2014 Figure 5. Removing the DIN clip before mounting to a flat surface. 6. Figure 7. Routing I/O wiring. 8. Connect wiring to power and I/O terminals. Mount the back plate as appropriate. If mounting to a DIN rail, pull the clips back so that the DIN track is completely clear. Place the unit on the DIN rail, then press both clips inwards to lock. Figure 8. Power Wiring. Figure 9. FLN 2 wire network interface. Figure 6.
PAGE 4
Document No. 550-992 Installation Instructions August 20, 2014 (PPM-2U3322.BPF and PPM-2U3322.BPR) Figure 11. Wiring I/O to terminals. (PPM-3U63.BPR, for China only) Figure 14. 12 Point Combination controller board. Figure 12. 6 Point Digital controller board. 9. Set the address using DIP Switches 1 through 8 (Binary 0 to 255) Example 1: Switch 7 and 8 ON = Address 3. Example 2: Switch 5 and 8 ON = Address 9. 10. Note the device’s MAC and network number, as this may be required for startup. 11.
PAGE 5
Document No. 550-992 Installation Instructions August 20, 2014 13. Snap the front cover on. A POWER/RX LED solid ON indicates that the unit is powered, but no communication. A flashing LED indicates that the unit successfully receiving packets on the network. 14. Using the permanent marker or label maker, record the physical point assignments, the network number and MAC address on the label. The installation is complete. Figure 15. Installing front cover to back plate. Figure 16. MSTP PPM Dimensions.
PAGE 6
Document No. 550-992 Installation Instructions August 20, 2014 I/O Configuration Diagrams Figure 19. Analog input wiring. Figure 17. AI/DI wiring for 6 point digital. Figure 20. Universal input wiring. Figure 21. Analog output wiring. Figure 18. DO wiring for wiring for 6 point digital. Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced.