Preface, Contents SIMATIC PC Panel PC 670 Computing Unit Equipment Manual Product Overview 1 Starting Up the Computing Unit 2 Connecting and Switching on the Computing Unit 3 Maintaining and Extending the Computing Unit 4 Configuring the Computing Unit in BIOS Setup 5 Fault Diagnosis 6 Hardware Information 7 Distributed Configuration 8 A Appendices C Glossary, Index This manual is only valid for computing units with Order No. 6AV77xx-...
Safety Guidelines This manual contains notices which you should observe to ensure your own personal safety, as well as to protect the product and connected equipment. These notices are marked as follows according to the level of danger: ! ! ! Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Correct Usage Please note the following: ! Warning The device may only be used for the application cases specified in the catalog and the technical description and may only be used in combination with third-party equipment and components recommended or approved by Siemens. Appropriate transport, and appropriate storage, installation and assembly, as well as careful operation and maintenance, are required to ensure that the product operates perfectly and safely.
For your notes
Preface Purpose The SIMATIC Panel PC 670 Computing Unit equipment manual is part of the SIMATIC HMI documentation. It provides information for operators, mechanics, project engineers and maintenance personnel about the computing unit’s installation, functionality, operation and technical structure.
Preface Release 04/02 Notation The following conventions are used in this manual: Motor on Text that is displayed on the operating unit is printed in Courier type face. Variable Symbolic names that stand for variable quantities that appear on the screen are printed in Courier italic type face. Screens Selectable functions are printed in italic type face. ESC Names of keys and buttons are shown in a different type face.
Preface Release 04/02 Automation and Drives, Service & Support Available round the clock, worldwide: Nuremberg Johnson City Singapore SIMATIC Hotline Worldwide (Nuremberg) Worldwide (Nuremberg) Technical Support Technical Support (FreeContact) (fee-based, only with SIMATIC Card) Local time: Mon.-Fri. 8:00 to 17:00 Local time: Mon.-Fri. 0:00 to 24:00 Telephone: +49 (180) 5050-222 Telephone: +49 (911) 895-7777 Fax: +49 (180) 5050-223 Fax: +49 (911) 895-7001 E-Mail: techsupport@ ad.siemens.
Preface Release 04/02 SIMATIC Customer Support Online Services The SIMATIC Customer Support team offers you substantial additional information about SIMATIC products via its online services: S General current information can be obtained – in the Internet unter http://www.siemens.com/simatic S Current Product Information leaflets, FAQs (Frequently Asked Questions), Downloads, Tips and Tricks can be obtained – in the Internet under http://www.siemens.
Contents 1 2 3 4 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 Advantages of the Computing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.2 Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 1.3 Certificates, Guidelines and Declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 1.
Contents 5 6 7 x Release 04/02 4.2 Installation of a Memory Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 4.3 Replacing the Backup Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 4.4 4.4.1 4.4.2 Installation of Extension Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing the module retainer plates . . . . . . . . . . . . . . . . . .
Contents Release 04/02 8 A B C 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 Monitoring Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signals on the front interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature monitoring/display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents xii Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Product Overview 1 Chapter Overview In Section You Will Find 1.1 Advantages of the computing unit 1-2 1.2 Safety notes 1-4 1.3 Certificates, guidelines and declarations 1-8 1.
Product Overview 1.1 Release 04/02 Advantages of the Computing Unit Computing unit The computing unit serves as a basic component for the PC-based HMI devices (Panel PC) and, within the scope of special configurations, as a basis for customized devices. The computing unit is intended for use in industry as well as in the residential, business and commercial areas and can also be used in building system automation or in public facilities, in addition to industrial applications.
Product Overview Release 04/02 Software equipment The computing unit is equipped with software which allows it to be used universally. It contains the operating system Windows NT 4.0, Windows 98 or Windows 2000.
Product Overview 1.2 ! Release 04/02 Safety Notes Caution Please observe the safety notes on the back of the cover of this manual. Expansions to the Panel PC should only be carried out after having read Chapter 4 and the relevant safety notes. This device complies with the safety requirements in accordance with IEC, VDE, EN, UL and CSA. If you have doubts about the approval of the installation in the intended location, please contact the service representative responsible for your area.
Release 04/02 Product Overview Mains supply When connecting the device, observe the relevant information provided in Chapter 2. Never connect or disconnect power cables or data transmission lines during a thunderstorm. In an emergency situation (for instance, damage to the housing, controls or power cable, penetration by liquids or foreign bodies), pull the power plug and contact the authorized service department. When plugging in/out periphery connections (e.g.
Product Overview Release 04/02 Country-Specific Notes For the USA and Canada: For operation in Canada and the United States, use CSA or UL-listed power cables. The connector must comply with the NEMA 5-15 specification. 120 V power supply A flexible cable with UL approval and CSA marking and the following features must be used: SJT design with three conductors, at least 18 AWG cross-section, a maximum length of 4.5 meters and parallel grounding-type plug (15 A, at least 125 V).
Product Overview Release 04/02 Batteries This unit contains batteries on the motherboard. The batteries may only be replaced by authorized, adequately trained personnel. When disposing of the batteries, observe the locally applicable laws on disposal of pollutants. ! Caution Improper replacement of the battery poses danger of explosion. Only replace with batteries of the same type or those of a similar type recommended by the manufacturer.
Product Overview 1.3 Release 04/02 Certificates, Guidelines and Declarations CE identification The SIMATIC product described in this manual fulfills the requirements to be awarded the CE identification.
Product Overview Release 04/02 Observe installation guidelines The installation guidelines and safety notes specified in this manual must be observed when starting up and operating the system. Connection of periphery devices The requirements concerning interference immunity are met when periphery equipment suitable for industrial demands, is connected in accordance with EN50082-2:1995. Periphery devices should only be connected using shielded cables.
Product Overview 1.4 Release 04/02 Certification for USA, Canada and Australia Safety If the device bears one of the following marks, the corresponding approval has been awarded: Underwriters Laboratories (UL) complying with Standard UL 1950 (I.T.E) or complying with UL508 (IND.CONT.EQ) C Underwriters Laboratories (UL) complying with Canadian Standard C22.2 No. 950 (I.T.E) or complying with C22.2 No. 142 (IND.CONT.
Product Overview Release 04/02 EMC USA Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Product Overview Release 04/02 Australia This product meets the requirements of the AS/NZS 3548 Norm.
Starting Up the Computing Unit 2 Chapter Overview In Section You Will Find on Page 2.1 Unpacking and checking the computing unit 2-2 2.2 Installing the computing unit 2-3 2.3 Ensuring Readiness for Service 2-7 2.
Starting Up the Computing Unit 2.1 Release 04/02 Unpacking and Checking the Computing Unit Unpacking the computing unit Unpack the item delivered to you as follows: 1. Remove the packaging. 2. Do not throw the original packaging away. Keep it in case you have to transport your PC at some time in the future. 3. Please keep the enclosed documentation in a safe place. You will require it when you first start up the item delivered to you and it is part of the device. 4.
Starting Up the Computing Unit Release 04/02 2.2 Installing the Computing Unit The unit delivered is particularly suited for installation in consoles, cabinets and panels. The computing units with AC power supply meet the requirements of the fire protection housing complying with EN60950.
Starting Up the Computing Unit Release 04/02 297 267 80 11 Figure 2-1 Dimension drawings for installation of the computing unit (device without CD-ROM drive) The computing unit contains a CD-ROM or CD-RW/DVD drive, depending on the unit version. The installation depth of the computing unit is increased by 21 mm as a result of its installation.
Release 04/02 Starting Up the Computing Unit Permissible installation positions for the computing unit complying with UL1950/EN60950/CSA22. 2 No. 950 An angle of inclination of ± 20_ is allowed installation position. Position 1 (preferred position) Position 2 *) Position 3 (desktop) Position 4 (cover) **) *) Not permitted where an LS240 drive is installed. **) Not permitted where a disk/CD-ROM/LS240 drive is installed.
Starting Up the Computing Unit Release 04/02 Additional permissible installation position for the computing unit complying with UL508/CSA 22.2 No. 142 An installation angle of ±15_ is permitted in this position. Position 5 (interfaces at bottom) Note The possible installation locations for the computing unit do not agree with the permissible installation location of Panel PC 670 (refer to the commissioning instructions).
Starting Up the Computing Unit Release 04/02 2.3 Ensuring Readiness for Service Measures for equipotential Low-resistance grounding connections ensure that the user of the installation is protected against electric shock (for example, if a short-circuit occurs or if there are defects in the system). Moreover, they discharge interference transmitted by external power supply cables, signal cables or cables to I/O devices.
Starting Up the Computing Unit Release 04/02 The AC power supply of the computing unit is designed for 120/230/240 V mains supplies. The power supply has a wide range input. There is no need to adjust the voltage range. The DC power supply of the computing unit is designed for 24 V mains supplies. One of these power supply is installed according to selection. Connecting and switching on the computing unit Before connecting computing unit to the mains, connect the front panels ready for operation. 1.
Release 04/02 2.4 Starting Up the Computing Unit Transport Shipping Despite the robust design of the computing unit, its built-in components are sensitive to severe vibrations and shock. Therefore, protect the computing unit from severe mechanical stress during transport. Only the original packing should be used when dispatching the Panel PC. Caution Risk of damage to the computing unit.
Starting Up the Computing Unit 2-10 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Connecting and Switching on the Computing Unit 3 Chapter Overview In Section You Will Find on Page 3.1 View of Interface Side 3-2 3.2 View of Drive Side 3-5 3.3 Connecting Peripheral Devices 3-6 3.4 Working with PC Cards 3-10 3.5 Drives 3-13 3.6 Backup battery 3-17 3.7 Using the Computing Unit in a SIMATIC S5 Network 3-18 3.8 Using the Computing Unit in a SIMATIC S7 Network (MPI/DP) 3-22 3.9 Networking the Computing Unit and Other Nodes via PROFIBUS 3-24 3.
Connecting and Switching on the Computing Unit 3.1 Release 04/02 View of Interface Side 1 2 13 12 Figure 3-1 1 3 4 11 5 10 9 8 6 7 Ports Mouse PS/2 socket for connecting a PS/2 mouse. 2 COM1 V.24 /MODEM /PLC The COM 1(TTY) interface can be used to connect e.g. S5 programmable controller (PLC). By implementing the adapter supplied, the interface can also be used as a 25-pin V.24 standard interface to connect devices with a serial interface, such as modem, mouse or printer.
Connecting and Switching on the Computing Unit Release 04/02 8 Ethernet RJ 45 Ethernet connection. The Ethernet network is a local network with a bus structure for data communication with data transmission rates of 10 or 100 megabits per second (mbps). 9 PROFIBUS/MPI Using the potential isolated PROFIBUS/MPI interface, the Box PC an can be connected to an S7 PLC or a PROFIBUS network. 10 USB Connections for Universal Serial Bus.
Connecting and Switching on the Computing Unit Release 04/02 VGA interface Please observe the following note on operating a flat display and an external monitor: Note The default setting of the display is simultaneous operation of a flat display and an external monitor. If no front display element is connected, the external monitor is used for the display, at a resolution of 640 x 480 pixels. Modes with a lower resolution and text modes are expanded to this format.
Connecting and Switching on the Computing Unit Release 04/02 3.2 View of Drive Side 1 2 5 Figure 3-2 1 3 4 Drive side Unit fan The air vents for the unit fan are located here. Caution The air vents must never be covered up, otherwise there is a risk of overheating. 2 Rating plate The rating plate contains the order no. and production serial no. (F-No.) of the unit. 3 Floppy disk drive A standard floppy disk drive (1.44 MB) is installed in the computing unit.
Connecting and Switching on the Computing Unit 3.3 Release 04/02 Connecting Periphery Units Note Make sure the components you insert exhibit industrial compatibility when connecting peripheral devices Printer connection via the parallel interface To connect your printer, perform the following steps: 1. Turn off the computing unit and the printer. 2. Plug the printer cable onto the parallel port, LPT 1. 3. Connect the printer cable to the printer. 4. Tighten (screw) the connector on the port.
Connecting and Switching on the Computing Unit Release 04/02 Printer connection via the parallel serial interface Alternatively, you can connect your printer via a serial COM interface to the computing unit. You will find information on how to adapt and set your port and on the connecting cable you should use in the user manual for your printer. Using a mouse A PS/2, USB or a serial mouse can be used in conjunction with the computing unit.
Connecting and Switching on the Computing Unit Release 04/02 Serial mouse connection You can connect a serial mouse to the serial port COM 2. To operate a serial mouse, you have to install and assign parameters to the suitable mouse driver. To do this, please refer to the description of your mouse or the description of your operating system for the necessary information. 1. Turn your device off. 2. Plug your serial mouse onto the mouse connector labeled COM 2. 3. Screw the connector tight. 4.
Connecting and Switching on the Computing Unit Release 04/02 USB device connection Individual or several USB devices can be connected to the USB interfaces. S Plug in the USB device connector into one of the USB interfaces. The device is detected by the Plug and Play operating system. Any necessary drivers are requested by the operating system. If more than two USB devices are to be connected, use a HUB. Both interfaces can be used as High Current interfaces.
Connecting and Switching on the Computing Unit 3.4 Release 04/02 Working with PC Cards PC cards Card bus cards (32 bit) and PCMCIA cards (16 bit) can be operated in the PC card interface. The computing unit is equipped with a PC card interface. Communication modules for MODEM, FAX/MODEM, ISDN, Token Ring, ETHERNET, memory expansions and check-card sized SCSI modules can be plugged into this interface.
Release 04/02 ! Connecting and Switching on the Computing Unit Caution Always discharge your body’s static charge before inserting or removing Cardbus/PC cards by briefly touching a grounded object (refer also the ESD Guideline, Appendix B). Damage could occur if you do not. Note Peak currents of 650 mA at 5 V referred to 3 s are allowed. Examples of PCMCIA cards on the PC card interface for hard disk drive 330 mA read/write (Maxtor MXL-131-III) . . . . . 640 mA spin up 2 s . . . . . . . . . . . . . . .
Connecting and Switching on the Computing Unit Release 04/02 Installation von PC cards Observe the following points when you install these cards: Note Depending on the configuration of the computing unit, it could be that there are no free interrupts for the operation of PC cards.
Connecting and Switching on the Computing Unit Release 04/02 3.5 Drives The computing unit is equipped with a 3.5” floppy disk drive or LS 240 drive and a 3.5” hard disk drive as standard equipment. 3.5.1 Floppy disk drive The floppy disk drive can be used to store programs and data on disks and load them from disk into the computing unit. Disk types The following disks can be used: double sided double density diskettes ! double sided high density diskettes LS240 superdisks 3.5 inch 3.5 inch 3.
Connecting and Switching on the Computing Unit Release 04/02 Handling LS240 drive disks The disks are inserted in the disk drive as illustrated below according to the installation position: Drill hole for emergency ejection (LS240 only) Eject button Access light Eject button Access light Figure 3-8 ! Handling Floppy Disks Caution Caution: This could result in loss of data! The eject button must never be pressed while the LS240’s green LED drive lamp is on.
Connecting and Switching on the Computing Unit Release 04/02 Notes on using the LS240 superdisks The LS240 drive supports the use of standard 3.5” disks with 1.44 Mbyte capacity as well as superdisks with a capacity up to 240 Mbyte. The track density of superdisks is 10 mm as compared to 120 mm with standard disks. The LS240 drive detects the presence of a superdisk and switches to the higher capacity.
Connecting and Switching on the Computing Unit 3.5.3 Release 04/02 Hard disk drive The hard disk is used to store large quantities of data. It is installed on a vibration-damped mounting that is easy to replace. ! 3.5.4 Caution Danger of data being lost and the drive damaged Drives are very sensitive to unacceptable vibrations. During operation, vibrations can result in a loss of data or damage to the drive or a data medium.
Release 04/02 Connecting and Switching on the Computing Unit Caution CD-ROM drives are sensitive to unacceptable vibrations. During operation, vibrations might damage the drive and/or the data medium. Additional software In order to use the full functional scope of the DVD-ROM/CD-RW drive, additional siftware is required (DVD player or printer software). It is part of the material supplied, being available on the CD.
Connecting and Switching on the Computing Unit 3.7 Release 04/02 Using the Computing Unit in a SIMATIC S5 Network Point-to-point connection This section describes the options for connecting your computing unit to a programming unit or an S5 programmable controller in a point-to-point connection. A point-to-point connection is possible by connecting the computing unit to another programming unit or a PLC via: S S a V.
Connecting and Switching on the Computing Unit Release 04/02 Connecting the computing unit to an S5 PLC You can connect the computing unit to a SIMATIC S5 programmable controller using the COM 1/TTY interface. COM 1 (Socket) Figure 3-9 Connection to an S5 Programmable Controller To connect the computing unit to a SIMATIC S5 programmable controller, perform the following steps: 1. Disconnect the computing unit from the mains power supply. 2. Plug the connecting cable onto the COM 1 port. 3.
Connecting and Switching on the Computing Unit Release 04/02 Connecting the computing unit via an adapter An adapter is available for connecting the computing unit to the PLC with earlier standard connecting cables. Table 3-1 Adapters for connecting the computing unit Interface Connection Connecting cable Order No.
Connecting and Switching on the Computing Unit Release 04/02 Connecting the computing unit to programming units (TTY) In order to connect the computing unit, connect the corresponding connection cable to the TTY interface. Table 3-2 Connecting the computing unit to other programming units Interface Connection COM 1 as TTY port with PG 6xx Connecting cable Order No. Series connection of 6ES5 733 -2xxx02) and 6ES5 731-6AG001) Adapter 6ES5 731-6AG00 Notice 1.
Connecting and Switching on the Computing Unit 3.8 Release 04/02 Using the Computing Unit in a SIMATIC S7 Network (MPI/DP) Connecting an S7 PLC via the MPI/DP interface Using the potential isolated*) MPI/DP interface, the computing unit can be connected to a SIMATIC S7 PLC or a PROFIBUS network. Using the MPI connection cable (5 m) for connection to the SIMATIC S7 CPUs (Order No.: 6ES7901-0BF00-0AA0), only transmission rates of up to 187.5 Kbit/s are possible. For baud rates from 1.
Release 04/02 Connecting and Switching on the Computing Unit MPI/PROFIBUS-DP network Up to 32 devices (PCs, programming units or PLCs) can be connected to the MPI/DP interface to form a network segment. The physical connection to the MPI/PROFIBUS-DP network is via an isolated RS485 interface, which is an integral part of the PC’s basic board. Several MPI/PROFIBUS-DP network segments can be connected via repeaters. The complete MPI/PROFIBUS-DP network can consist of up to 127 nodes.
Connecting and Switching on the Computing Unit 3.9 Release 04/02 Networking the Computing Unit and Other Nodes via PROFIBUS Networking the computing unit via PROFIBUS PROFIBUS is an open and robust bus system for industrial use. It can be used to configure networks with up to 32 nodes per segment. PROFIBUS-DP supports data rates of 9.6 KBaud to 12 MBaud. How the network functions The network operates on the ”token passing with subordinate master/slave” principle (complying with DIN 19245, PROFIBUS).
Release 04/02 3.10 Connecting and Switching on the Computing Unit Networking Computing Unit and Other Computers via Industrial Ethernet Networking the computing unit via Industrial Ethernet The RJ45 Ethernet interface is a Twisted Pair (TP) interface with a data transmissin rate of 10/100 Mbaud. The onboard interface is compatible with the Intel pro/100+ PCI adapter. The interface is Plug & Play capable and is automatically detected in Windows.
Connecting and Switching on the Computing Unit 3-26 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Maintaining and Extending the Computing Unit 4 Chapter overview You can enhance the functionality of your computing unit by installing additional main memory. This chapter describes how to expand your computing unit. Please observe the safety notes it contains. In Section You Will Find 4.1 Opening the Device 4-2 4.2 Installing Additional Memory 4-8 4.3 Replacing the Backup Battery 4-10 4.4 Installing Expansion Boards 4-12 4.5 Removing and Installing Drives 4-17 4.
Maintaining and Extending the Computing Unit 4.1 Opening the Unit 4.1.1 Conditions Release 04/02 The device is designed for easy maintenance so that any work that may be necessary can be done quickly and economically. Caution The electronic components on the printed circuit boards are extremely sensitive to electrostatic discharge. Certain precautionary measures are therefore necessary when handling such components.
Maintaining and Extending the Computing Unit Release 04/02 Before opening the device Note the following rules before opening the device: ! S Before you disconnect the power supply cable, discharge the electrostatic charge on your body. You can do this by briefly touching the mounting plate for the interfaces on the left side of the device. S Discharge the electrostatic charge from tools you are using. S Wear a grounding strap when handling components.
Maintaining and Extending the Computing Unit 4.1.2 Release 04/02 Opening the computing unit To open the computing unit, perform the following steps: 1. Turn off the computing unit, pull out the mains connector and remove all interconnecting cables and connecting cables from the device, including the keyboard cable. 2. Remove the computing unit from its mounting/cabinet (only necessary if mounting screws are inaccessible as a result of installation). 3.
Maintaining and Extending the Computing Unit Release 04/02 4.1.3 Functional Units Visible After Opening the Device View The function units become visible after removing the top cover of the unit and removing the hard disk module.
Maintaining and Extending the Computing Unit 4.1.4 Release 04/02 Motherboard S1 X401 Figure 4-3 4-6 X28 X128 T1 X29 X24 X20 X19 X500 X600 X40 X11 X9 X6 X14 X700 X10 X70 X25 X13 T3 X26 X41 X4 X5 X71 X3 X31 T2 X420 X1 X23 X44 X400 X402 The motherboard is the heart of the computing unit. Here, data are processed and stored, and interfaces and device I/Os are controlled.
Maintaining and Extending the Computing Unit Release 04/02 Components on the motherboard The following components are located on the computing unit: Number Functions X1 Processor module with heat sink X3 IDE connector for CD-ROM X4 IDE connector for 2.
Maintaining and Extending the Computing Unit 4.2 Release 04/02 Installation of a Memory Extension Standard memory The motherboard has 2 slots for 144 pin SO DIMM memory modules. This allows you to expand the memory capacity of your computing unit to 512 Mbytes. One or two modules can be equipped.
Release 04/02 ! Maintaining and Extending the Computing Unit Caution The electronic components on the printed circuit boards are extremely sensitive to electrostatic discharge. Certain precautionary measures, therefore, have to be taken when handling them. These measures are explained in the guidelines for electrostatically sensitive devices in Appendix B. Installing the SO DIMM Modules To insert the modules, perform the following steps: 1. Open the unit first as described in section 4.1. 2.
Maintaining and Extending the Computing Unit 4.3 Release 04/02 Replacing the Backup Battery Battery power supply for real-time clock and configuration A backup battery (3.6 V lithium battery) powers the real-time clock even after the unit has been turned off. In addition to the time of day, all the information about the device (device configuration) is stored. If the backup battery fails or is removed from its plug, these data are lost.
Maintaining and Extending the Computing Unit Release 04/02 Backup battery Figure 4-5 ! Position of the backup battery Caution Danger of damage! Only replace the lithium battery with an identical battery or with a type recommended by the manufacturer (Order No: W79084-E1003-B1). If possible, return old lithium batteries to the manufacturer or recycling facility or dispose of them as special waste.
Maintaining and Extending the Computing Unit 4.4 Release 04/02 Installation of Extension Modules Notes on the boards The computing unit is designed for the use of cards as per the AT/PCI specification. The dimensions of the cards must not exceed the stated dimensions. If the height is exceeded, contact problems, malfunctions and difficulties with installation cannot be ruled out. The illustrations show full length AT/PCI cards.
Maintaining and Extending the Computing Unit Release 04/02 Figure 4-8 106.68 mm 4.2” 8.19 mm 0.322” 174.63 mm 6.875” Short PCI card (5 V) Figure 4-9 106.68 mm 4.2” 8.19 mm 0.322” 265 mm 10.48 ” Long PCI card (5 V) Note on long PCI cards Before long PCI cards can be inserted in the guides of the fan trough, they must be fitted with an extender (this should be included with the long PCI board). Long PCI cards can be inserted in the guides of ISA modules by means of this extender.
Maintaining and Extending the Computing Unit 4.4.1 Release 04/02 Removing and installing the module retainer plates The module retainer plate is attached to the housing by a screw. It has three slits, through which the slide elements are inserted. To change the battery, perform the following steps: 1. Open the housing as described in section 4.1. 2. Undo the fixing screw of the module retainer plate. 3. During assembly, ensure that the module retainer plate is resting on the guide on the system housing.
Maintaining and Extending the Computing Unit Release 04/02 Adjusting the module retainer plate Proceed as follows to install the module retainer plate. 1. Insert the slide element through the guide slit until it is resting firmly on the module. The module must now be introduced into the notch. Caution Do not exert pressure on the module! Therefore, do not use force to press the slide module onto the module. 2.
Maintaining and Extending the Computing Unit 4.4.2 Release 04/02 Removing and installing an ISA/PCI module To change the battery, perform the following steps: 1. Open the housing as described in section 4.1. 2. Disconnect all the connectors from the expansion module and note their assignment. 3. Remove the module retainer plates as described in section 4.4.1. 4. Undo the screw on the slot plate of the module. 5. Pull the module out of its slot. 6.
Maintaining and Extending the Computing Unit Release 04/02 4.5 Removing and Installing Drives The basic configuration of the computing unit includes a 3.5” floppy disk drive and a 3.5” hard disk drive. An LS 240 drive is possible for custom solutions. 4.5.1 Removing and installing the hard disk drive 1. Remove the 4 screws on the back of the system housing. 2. Swing open the drive cage. 3. Detach the drive holder from its mounting and place it face down on the housing. 4.
Maintaining and Extending the Computing Unit Figure 4-13 4-18 Release 04/02 Hard disk drive, with holder, removed Panel PC 670 Computing Unit, Equipment Manual
Maintaining and Extending the Computing Unit Release 04/02 4.5.2 Removing and installing a CD-ROM drive Depending on the hardware configuration of the device, a CD-ROM drive is installed on the computing unit. The installation depth of the computing unit is increased by 21 mm as a result of its installation. 1. Undo the 2 screws on the back of the system housing. 2. Remove the cover of the CD-ROM drive. 3. Undo the three screws which secure the CD-ROM on the mounting. 4.
Maintaining and Extending the Computing Unit 4.5.3 Release 04/02 Removing and installing the disk drive 1. Open the housing as described in Chapter 4.1. 2. Remove the drive mounting as described in section 4.5.1. 3. Undo the interlocking of the controller flexible cable on the motherboard and pull the flexible cable out of the plug connection. 4. Undo the two fixing screws (TORX T8) on the housing. 5. Lift the floppy disk drive up and out of the housing. 6.
Maintaining and Extending the Computing Unit Release 04/02 4.5.4 Removing and installing the LS 240 drive To remove and install the LS240 drive, perform the same steps as for installing the floppy disk drive. 1. Open the housing as described in Chapter 4.1. 2. Remove the drive mounting as described in section 4.5.1. 3. Release the cable clamp assembly of the controller flexible cable on and pull the flexible cable out of the plug connection. 4. Undo the two fixing screws (TORX T8) on the housing. 5.
Maintaining and Extending the Computing Unit 4.6 Release 04/02 Removing and Installing the Power Supply 1. Open the housing as described in section 4.1. 2. Remove the drive mounting as described in section 4.5.1. 3. Remove the 3 screws from the cover of the power supply unit from the housing. 4. Disconnect the internal SV cable on the power supply (only applicable to units with 105 W power supplies). 5. Remove the two fixing screws (TORX T10) on the housing. 6.
Maintaining and Extending the Computing Unit Release 04/02 4.7 Removing and Installing the Bus Board 1. Open the housing as described in section 4.1. 2. Remove all the modules from their slots (perform the steps described in section 4.4.2). 3. Remove the drive mounting as described in section 4.5.1. 4. Remove the power supply unit as described in section 4.6. 5. Undo the screw on the motherboard. 6. Pull the wiring backplane from the motherboard. 7.
Maintaining and Extending the Computing Unit 4.8 Release 04/02 Removing and Installing the Motherboard 1. Open the housing as described in section 4.1. 2. Remove all the modules from their slots (perform the steps described in section 4.4.2). 3. Remove the drive mounting as described in section 4.5.1. 4. Remove the power supply unit as described in section 4.6. 5. Undo 7 screws on the motherboard and undo 10 hexagon head cap screws at the interfaces. 6. Remove the wiring backplane and the motherboard. 7.
Maintaining and Extending the Computing Unit Release 04/02 4.9 Removing and Installing the Fan The computing unit is cooled by means of a fan, which extracts hot air out of the housing. 1. Open the housing as described in section 4.1. 2. Disconnect the fan cable connector from the motherboard. 3. The fan is secured to the housing by two plastic rivets. Undo the rivets by pressing out the gudgeon from the rear of the rivet shank. 4. Remove the fan. 5. Proceed in the reverse order for assembly.
Maintaining and Extending the Computing Unit 4.10 Release 04/02 Processor Upgrade You can boost the performance capability of your computing unit by installing other processors. Proceed as follows to replace the processor (the numbers in brackets relate to Figure 4-21): 1. Disconnect the fan cable connector from the motherboard. 2. Remove the heat sink, secured by a metal bar. 3. Press the lever in the direction of the arrow (1) and pivot it up as far as possible (2). 4.
Maintaining and Extending the Computing Unit Release 04/02 4.11 Reset button A hardware reset is initiated by means of the Reset button on your device. The computing unit is restarted. On the computing unit, the Reset button is located on the drive side beside the floppy disk drive. The Reset button can only be operated with the aid of a pointed object (e.g. the tip of a ball-point pen or straightened paper clip). The position of the Reset button is marked in the illustration of the computing unit below.
Maintaining and Extending the Computing Unit 4-28 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Configuring the Computing Unit in BIOS Setup 5 Chapter Overview In this chapter, you will learn how to configure your computing unit. You need to do this if you want to change your system by adding, removing, or exchanging an extension board, memory expansion module, or by replacing a system module. In Section You Will Find on Page 5.1 Modifying the Device Configuration with SETUP 5-2 5.1.1 The Main Menu 5-5 5.1.2 The Advanced Menu 5-15 5.1.3 The Security Menu 5-22 5.1.
Configuring the Computing Unit in BIOS Setup 5.1 Release 04/02 Modifying the Device Configuration with SETUP Changing the Device Configuration The device configuration of your computing unit is preset for working with the software supplied to you. You should only modify the preset values if you have performed technical modifications to your device or if a fault occurs when the unit is powered up. BIOS SETUP Program The SETUP program is in the ROM-BIOS.
Release 04/02 Configuring the Computing Unit in BIOS Setup Screen Display Following Power On For example, the default setting of your computing unit will display the following figure on the display on power on: Phoenix BIOS 4.0 A5E00123801–ES02 Copyright 1985-2001 Phoenix Technologies Ltd. All Rights Reserved. SIMATIC Box PC 620 V02.01.
Configuring the Computing Unit in BIOS Setup Release 04/02 Menu items After BIOS Setup has started, the following dialog box appears on the screen: PhoenixBIOS Setup Utility Title bar Main Advanced Security Power Boot Sequence Version Exit Menu bar Selectable submenu System Time: System Date: [ 15:35:32 ] [ 03/12/2002] Diskette A: Primary Master Primary Slave Secondary Master Secondary Slave [1.
Configuring the Computing Unit in BIOS Setup Release 04/02 5.1.1 Menu Main PhoenixBIOS Setup Utility Main Selectable submenu Advanced Security System Time: System Date: [ 15:35:32 ] [ 03/12/2002 ] Diskette A: Primary Master Primary Slave Secondary Master Secondary Slave [1.
Configuring the Computing Unit in BIOS Setup Release 04/02 System Time und System Date Time and date System Time and System Date indicate the current values. Once you have selected the appropriate option, you can use the [+] and [–] keys to modify the time setting Hour:Minute:Second and the date Month/Day/Year. You can move between the entries in the date and time options (for example, from hour to minute) using the tabulator key.
Configuring the Computing Unit in BIOS Setup Release 04/02 Primary Master, Primary Slave, Secondary Master, Secondary Slave The system jumps to the following submenu when you select this type of menu field: PhoenixBIOS Setup Utility Main Primary Master [20496 MB] [ Auto ] Type: Total Sectors: Maximum Capacity: LBA Format 40031712 20496 MB Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: F1 ESC Figure 5-3 Help Exit [16 Sectors] [Enabled] [Enabled] [FPIO 4 / DMA
Configuring the Computing Unit in BIOS Setup Release 04/02 Multi Sector Transfer field In the box Multi Sector-Transfer the number of blocks (sectors) are defined that will be transmitted with one interrupt. The value depends on the drive and should be set only by setting the Type field to ”Auto”. Disabled 2,4,8,16 sectors LBA Mode Control field If the LBA Mode Control field (enabled,disabled) is set to ’Enabled’, the system supports hard disks with capacities greater than 528 Mbytes.
Configuring the Computing Unit in BIOS Setup Release 04/02 ”Memory Cache” Submenu The following pop-up menu appears when you select the submenu “Memory cache” in the main menu: PhoenixBIOS Setup Utility Main System Time: System Date: Diskette A: [ 15:35:32 ] [ 03/12/2002 ] [1.
Configuring the Computing Unit in BIOS Setup Release 04/02 Submenu ”Boot Options” The following submenu appears when you select the option “Boot Options” in the main menu: PhoenixBIOS Setup Utility Main Boot Options QuickBoot Mode: [Enabled] SETUP prompt: POST Errors: [Enabled] [Enabled] Floppy check: [Disabled] Summary screen: [Enabled] F1 ESC Figure 5-5 5-10 Item Specific Help Help Exit Select Item Select Menu Allows the system to skip certain tests while booting.
Configuring the Computing Unit in BIOS Setup Release 04/02 Floppy check The floppy head is stepped inward and then back to its original position during the system run-up phase. This test is useful because it reinitializes the drive. Summary screen The most important system parameters are displayed when the system run-up phase completes. ’Enabled’ means that the feature is active. ’Disabled’ means that the feature is inactive.
Configuring the Computing Unit in BIOS Setup Release 04/02 Submenu ”Keyboard Features” The following submenu appears if you select the “Keyboard Features” field in the main menu: PhoenixBIOS Setup Utility Main Keyboard Features Item Specific Help Selects Power-On state for NumLock on next boot [ On ] NumLock: Key Click: [Disabled] [30/sec] Keyboard auto-repeat rate: Keyboard auto-repeat delay: [1/2 sec] F1 ESC Figure 5-7 5-12 Help Exit Select Item Select Menu + / – Change Values Enter Select Sub-
Configuring the Computing Unit in BIOS Setup Release 04/02 Submenu ”Hardware Options” The following submenu appears when you select the “Hardware Options” field in the main menu: PhoenixBIOS Setup Utility Main Hardware Options PCI – MPI / DP: Onboard Ethernet: Ethernet Address: LAN Remote Boot: Cardbus/PCMCIA Slot: SafeCard functions: Legacy USB Support: Fan Control: CRT / LCD selection: LCD-Screensize: DSTN Contrast: [ Enabled ] [Enabled] 08000624xxxx [Disabled] [Enabled] [Enabled] [Disabled] [Enabled
Configuring the Computing Unit in BIOS Setup Entry Card bus / PCMCIA Slot SafeCard functions Release 04/02 Meaning [Disabled] Release the Cardbus / PCMCIA interfaces is disabled. [Enabled] The resources are managed by the BIOS PCI plug and play mechanism. [Enabled] On board monitoring functions are enabled. [Disabled] No monitoring functions. The relevant driver and application must be started for operation of the monitoring functions.
Configuring the Computing Unit in BIOS Setup Release 04/02 5.1.
Configuring the Computing Unit in BIOS Setup Large Disk Access Mode [DOS] Release 04/02 The drive tables are adapted for DOS access operations in accordance with Enhanced IDE. [OTHER] The tables are not adapted. Memory Gap at 15 MByte [Disabled] The complete onboard RAM memory is available. [Enabled] A 1MB area of the RAM above 15MB (Addresses F0 0000 – FF FFFF) can be used by ISA expansion cards.
Configuring the Computing Unit in BIOS Setup Release 04/02 Printer Port Internal LPT1 Mode: Use this setting to set the operating mode of the printer interface. Refer to the table below to ensure that the setting matches the printer connected to the printer port.
Configuring the Computing Unit in BIOS Setup Release 04/02 PCI Configuration Submenu PhoenixBIOS Setup Utility Advanced PCI Configuration Item Specific Help PCI Device, Slot #1 PCI Device, Slot #2 Setup items for configuring The specific PCI device PCI/PNP ISA IRQ Resource Exclusion PCI PCI PCI PCI line line line line 1: 2: 3: 4: Help Exit F1 ESC Figure 5-11 IRQ IRQ IRQ IRQ [Auto Select] [Auto Select] [Auto Select] [Auto Select] Select Item Select Menu + / – Change Values Enter Select Sub-Me
Configuring the Computing Unit in BIOS Setup Release 04/02 Option ROM Scan: [Enabled] [Disabled] The option ROM of the PCI module (if present) is enabled The option ROM of a PCI module is disabled. Enable Master: [Enabled] [Disabled] This slot can assume the PCI master function This slot can only operate as a PCI slave.
Configuring the Computing Unit in BIOS Setup Release 04/02 “PCI IRQ line” Field PhoenixBIOS Setup Utility Advanced PCI Configuration Item Specific Help PCI Device, Slot #1 PCI Device, Slot #2 Reserves the specified IRQ for use by legacy ISA devices Disabled PCI/PNP ISA IRQ Resource Exclusion Autoselect 3 PCI IRQ line 1: 4 PCI IRQ line 2: 5 7 PCI IRQ line 3: 9 PCI IRQ line 4: 10 11 12 14 15 F1 ESC Figure 5-14 5-20 Help Exit Select Item Select Menu + / – Change Values Enter Select Sub-Menu F9 Se
Configuring the Computing Unit in BIOS Setup Release 04/02 Submenu “Video Adapter Settings” PhoenixBIOS Setup Utility Advanced Video Adapter Settings Frame Buffer Size: AGP Rate: [8 MB] [2x] Default Primary Video Adapter: [AGP] F1 ESC Figure 5-15 Item Specific Help Help Exit Select Item Select Menu On board video adapter buffer size, which is shared with Main Memory + / – Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Submenu ”Video Adapter Settings” Frame Buffer Si
Configuring the Computing Unit in BIOS Setup 5.1.3 Release 04/02 Menü Security Overview You can only edit the fields enclosed in square brackets. In order to protect your computing unit against illegal use it is possible to enter two passwords. With the supervisor password, the setup access can be restricted or denied to normal users.
Configuring the Computing Unit in BIOS Setup Release 04/02 Password on boot [Disabled] No password required for system boot. [Enabled] Supervisor or user password must be entered for system boot. Fixed disk boot Sector [Normal] All types of hard-disk access are permitted. Diskette access This mode of protection is not active unless ”Password on boot ” is set to [enabled]. [Write protect] No operating system can be installed. This is a way of protecting against boot viruses.
Configuring the Computing Unit in BIOS Setup 5.1.4 Release 04/02 Menu Power Overview This menu has the following structure.
Configuring the Computing Unit in BIOS Setup Release 04/02 Hard Disk Timeout 5.1.5 [Disabled] [10, 15, 30, 60] The hard disk does not shut down. Time since the last hard-disk access, the hard disk is shut down. On the next access the hard disk will be activated again with a short delay. Menu Boot-Sequence Overview This menu lists the boot devices in prioritized groups.
Configuring the Computing Unit in BIOS Setup Release 04/02 Groups marked + contain more than one device. When you select a group marked in this way, hit Enter to view the list of devices in the group.
Configuring the Computing Unit in BIOS Setup Release 04/02 5.1.6 Menu Version This menu contains the information you will have to quote when you send us technical questions about your system. PhoenixBIOS Setup Utility Main Advanced Security Power Boot Sequence Version Exit Item Specific Help SIMATIC Box PC 620 Bios Version Bios Number V02.01.
Configuring the Computing Unit in BIOS Setup 5.1.7 Release 04/02 Menu Exit The Exit Menu The setup program is always terminated using this menu. PhoenixBIOS Setup Utility Main Advanced Security Power Version Boot Sequence Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Setup Defaults Load Discard Changes Save Changes F1 ESC Figure 5-21 Help Exit Select Item Select Menu Exit System Setup and save your change to CMOS.
Configuring the Computing Unit in BIOS Setup Release 04/02 5.1.8 Setup default settings Documenting your device configuration If you have made any modifications to the default Setup settings, you can enter them in the following table. You can then refer to these entries if you need to make any hardware modifications later. Note Print the following table out and keep the pages in a safe place once you have filled in your entries.
Configuring the Computing Unit in BIOS Setup System Parameters Cardbus/PCMCIA Slot SafeCard Functions Legacy USB Support CRT/LCD selection LCD Screensize DSTN Contrast PS2 Mouse Advanced COM/LPT Configuration Internal COM1 Base I/O address Interupt Internal COM2 Base I/O address Interrupt Internal LPT1 Mode Base I/O address Interrupt DMA Channel (only for ECP) PCI Configuration PCI Device Slot 1 Option ROM Scan Enable Master Latency Timer PCI Device Slot 2 Option ROM Scan Enable Master Latency Timer PCI/P
Configuring the Computing Unit in BIOS Setup Release 04/02 System Parameters Standard Settings Floppy disk controller Local Bus IDE adapter Large Disk Access Mode Hard Disk Pre-Delay Memory Gap at 15 MByte Enabled Both DOS Disabled Disabled Video Adapter Settings Frame Buffer Size AGP Rate Default Primary Video Adapter 8 MB 2x AGP Security Supervisor Password Is User Password Is Set Supervisor Password Set User Password Password on boot Fixed disk boot sector Diskette Access Disabled Disabled F0 5A
Configuring the Computing Unit in BIOS Setup 5.2 Release 04/02 Configure PC-Card interface You can obtain the software you require for using PC cards under MS DOS, such as S Socket Services S Card Services S Client Drivers S Flash File System can be obtained from the nearest Siemens sales office or representative. Your PC comes supplied with Windows 98 / NT4 / 2000 already installed; this supports the PC Card interface. After completing the configuration the computing unit has to be booted.
Fault Diagnosis 6 Chapter overview This chapter provides information on localizing problems which frequently occur and how to clear them. Note Please refer to the operating system documentation with regard to error messages concerning the operating system. In Section You Will Find on Page 6.1 Problems Using External Modules 6-2 6.2 External Screen Remains Dark 6-3 6.3 Display on the External Screen Does Not Appear or Scrolls 6-4 6.4 No Mouse Pointer Appears on the Screen 6-4 6.
Fault Diagnosis 6.1 Release 04/02 Problems Using External Modules Fault screen Computing unit crashes during boot routine.
Fault Diagnosis Release 04/02 6.2 External Screen Remains Dark Cause/Remedy The following causes are possible: Monitor is switched off S Switch on the screen. Screen has been dimmed S Press any key on the keyboard. Brightness control set to dark S Set the screen brightness control lighter. Please refer to the monitor operating manual for more detailed information. Power cable or monitor cable not connected S Switch the monitor and computing unit off.
Fault Diagnosis 6.3 Release 04/02 Display on the External Screen Does Not Appear or Scrolls Cause/Remedy The incorrect line frequency and/or resolution is set for the screen or the application program. 6.4 S Exit from the application program. If the fault continues to occur after terminating the program, switch the monitor off and then on again following a wait of at least 3 seconds. S Adapt the entries for the screen in the CONFIG.SYS file accordingly (on the hard disk).
Release 04/02 6.5 Fault Diagnosis Computing Unit Time and/or Date are Not Correct Remedy Correct the time and date in the Setup menu. Press F2 during the boot routine to call in the Setup menu (refer to Chapter 5). Note If the date and time remain incorrect after switching the unit off and on again, the battery is empty. Information on changing the backup battery is available in Chapter 4.3. 6.6 USB Device Does Not Work The USB interface is not detected by the operating system.
Fault Diagnosis 6.7 Release 04/02 Error Message Appears on the Screen/Display Error messages The error messages issued by the system BIOS are listed below. Refer to the relevant program manuals in the case of error messages issued by the operating system or programs. Press F2 during the boot routine to call in the Setup menu (refer to Chapter 5). Error message on screen Significance/Advice Address conflict Plug and Play Problem Contact your technical service department.
Fault Diagnosis Release 04/02 Error message on screen Significance/Advice Operating system not found Possible causes: No operating system available Wrong drive triggered (disk in drive A/B) Wrong active boot partition Wrong drive entries in SETUP Previous boot incomplete Default configuration used Termination of the previous boot routine, e.g. through power failure. Correct entries in SETUP.
Fault Diagnosis 6.8 Release 04/02 Computing Unit Self-Test Prior to Booting After switching on the SIMATIC PC a self-test is initiated (POST = Power On Self Test). If errors are detected during the POST, the corresponding sequence of POST beeps (beep code) are issued. Each beep code consists of 2 x 2 sequences. In addition, the individual test steps which the self-test executes, are issued on the I/O port 80h.
Fault Diagnosis Release 04/02 POST codes The POST codes in order of occurrence: Display (hex) Meaning Description 02 TP_VERIFY_REAL Test whether the CPU is in real mode 1C TP_RESET_PIC Reset the interrupt controller 12 TP_RESTORE_CRO Restore the controller register 13 TP_PCI_BM_RESET Reset the PCI bus master 36 TP_CHK_SUTDOWN Check the shutdown code 24 TP_SET_HUGE_ES Switch the ES to special mode 03 TP_DISABLE_NMI Switch off the NMI 0A TP_CPU_INIT Early initialization of the CPU
Fault Diagnosis Release 04/02 Display (hex) Meaning Description 46 TP_COPYRIGHT Test the copyright 49 TP_PCI_INIT Initialize the PCI interface 48 TP_CONFIG Check the configuration 4A TP_VIDEO Initialize the video interface 4C TP_VID_SHADOW Copy the video BIOS to RAM 24 TP_SET_HUGE_ES Switch the ES to special mode 22 TP_8742_TEST Test module 8742 52 TP_KB_TEST Keyboard available? 54 TP_KEY_CLICK Switch the keyboard click on/off 76 TP_KEYBOARD Check the keyboard 58 TP_HOT_I
Fault Diagnosis Release 04/02 Display (hex) Meaning Description 82 TP_RS232 Determine the serial interfaces 84 TP_LPT Determine the parallel interface 86 TP_IO_AFTER Re-enable the IO modules 83 TP_FDISK_CFG_IDE_CTRLR Configure the IDE controller 89 TP_ENABLE_NMI Enable the NMI 8C TP_FLOPPY Initialize the floppy controller 90 TP_FDISK Initialize the hard disk controller 8B TP_MOUSE Test the internal mouse interface 95 TP_CD Test the CP 92 TP_USERPATCH2 Area for own initializ
Fault Diagnosis 6-12 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Hardware Information 7 Chapter Overview In Section You Will Find 7.1 Current Requirement of the Components (Maximum Values) 7-2 7.2 Overview of the Components and Ports 7-3 7.3 System Resources 7-5 7.4 Monitoring Functions 7-6 7.5 Interfaces 7-10 7.6 Wiring backplane 7-32 7.7 Power Supply Unit 7-37 7.
Hardware Information 7.1 Release 04/02 Power Consumption of the Components (Maximum Values) Basic system Component Voltage +5V Pentium III Motherboard 0.5 A Processor Pentium III 1260 5A Floppy disk drive / LS 240 0.56 A Hard disk 0.4 A CD RW/DVD drive 0.92 A +3.3V 2.5 A –12V 0.02 A 0.5 A 0.2 A Sum (max. for basic configuration) 7.38 A 2.5 A ISA/PCI slots (Sum) 3A 4A 1 PC card slot 0.5 Sum (max. for maximum configuration) 13.5 A Total power consumption 105W 7-2 –5V 0.
Hardware Information Release 04/02 7.2 Overview of the Components and Interfaces Component/ Port Description Chipset VIA PN133T BIOS Update via software CPU Pentium III / Celeron (type FC-PGA370) Parameters S SDRAM S 512K in 4 pages S Upgradeable S Multimedia support S On Board L2-Cache with 128 k/256 k /512 K Memory Graphics card DIMM modules up to max.
Hardware Information Component/ Port Release 04/02 Description Parameters Parallel Standard, bidirectional, EPP and ECP modes S 25 pin subminiature Cannon connector DP12 Communication port SIMATIC S7 S potentially isolated DP12 *1 (CP 5611 compatible) S 12MBaud USB Universal Serial Bus S three high current (500mA) USB ports (2x external and 1x internal) Ethernet *1 7-4 10BaseT/100Base-TX (Intel 82559) S 10/100 Mbps, potentially isolated *1 Electrically isolated in a safety extra-low voltag
Release 04/02 7.3 Hardware Information System Resources All system resources (Hardware adresses, Memory allocation, Interrupt allocation, DMA channels) are dinamically assigned by the Windows operating system depending on the specific hardware, drivers and connected external devices.
Hardware Information 7.4 Release 04/02 Monitoring Functions The LEDs described in the following sections are only available on specific versions of the device. The basic configuration of the computing unit does not have any LEDs. The hardware signals are described in Section 7.5.2. 7.4.
Hardware Information Release 04/02 7.4.3 Temperature monitoring/display Temperature monitoring The temperature is measured by means of three temperature sensors. One sensor monitors the processor temperature, the second the temperature in the area of the memory module and the expansion cards and the third the temperature in the area of the power supply unit. S If the temperature near the power supply exceeds 45oC (fixed value), the fan is set to maximum rpms.
Hardware Information 7.4.4 Release 04/02 Watchdog (WD) Function The watchdog monitors the execution of a program. The purpose of the WD is to report a program crashing to the user by means of different reactions. After switching on the computing unit or after a HW-RESET (cold start) the watchdog remains in standby, i.e. no WD reaction is activated and the RUN-LED remains switched off. If the watchdog is activated (by driver or SOM program) the Run LED is green.
Hardware Information Release 04/02 7.4.5 Fan monitoring The operation of the processor fan is monitored. If the fan should fail, the following reactions are triggered: Reaction Options Temp LED from GREEN to RED – Trigger IRQ Adjustable The error remains saved until the cause of the failed fan is removed and the temperature error is reset by one of the following measures. S Acknowledgement of the error message via the SOM program. S Restarting the device.
Hardware Information 7.5 Release 04/02 Interfaces The following interfaces are available on the computing unit’s mainboard: S ports for connecting external devices S ports for connecting displays S ports for internal connections (drives, wiring backplane, etc.) The connector pin-outs of the different ports are described in the sections below. 7.5.
Hardware Information Release 04/02 Serial interface COM1 (AG/V24/Modem) The serial interface (COM 1) of the computing unit is assigned as follows: 1 13 Figure 7-1 14 25 Serial interface COM1 (female) Pin No.
Hardware Information Release 04/02 Serial interface COM2 (V24/Mouse) The serial interface (COM2) of the computing unit is assigned as follows 5 9 1 Figure 7-2 7-12 6 Serial interface COM2 (male) Pin No.
Hardware Information Release 04/02 Parallel interface LPT1 The parallel interface (LPT1) of the computing unit is assigned as follows: 1 13 Figure 7-3 14 25 Parallel interface LPT1 (female) Pin No.
Hardware Information Release 04/02 PS/2 mouse interface It is possible to connect a PS/2 mouse to the computing unit. The port is assigned as follows: 6 5 4 3 2 1 View of Socket Figure 7-4 Connector Pinout for a PS/2 Mouse Pin No.
Hardware Information Release 04/02 6 5 4 3 2 1 View of Socket Figure 7-5 Connector Pinout for an External Keyboard Connecting Cable Pin No. Short Name Meaning Input/Output 1 DAT Keyboard data Input/Output 2 - Not assigned - 3 GND Chassis ground - 4 P5VFK +5V ( fused) Output 5 CLK Keyboard clock line Input/Output 6 - Not assigned - USB interface The allocation of the Universal Serial Bus interfaces is as follows: 4 3 2 1 Figure 7-6 USB interface Pin No.
Hardware Information Release 04/02 MPI/DP interface The MPI/DP port on the computing unit is assigned as follows: 1 5 Figure 7-7 9 PROFIBUS/MPI Socket Connector Pin No. Short Name Meaning Input/Output 1 - Not assigned - 2 - Not assigned - 3 LTG_B Signal lead B of MPI module Input/Output 4 RTS_AS RTSAS, control signal for received data stream. The signal is ’1’ active when the directly connected AS is sending. Input 5 M5EXT M5EXT return line (GND) of the 5 V power supply.
Hardware Information Release 04/02 Ethernet RJ45 connection The Ethernet-RJ45 interface of the computing unit is assigned as follows: LED yellow 1 Figure 7-8 LED green 8 Ethernet port Pin No.
Hardware Information Release 04/02 VGA interface The VGA socket on the computing unit is assigned as follows: 6 11 1 5 Figure 7-9 7-18 10 15 VGA Socket Connector Pin No.
Hardware Information Release 04/02 7.5.
Hardware Information Pin Release 04/02 Signal Meaning DSTN DSTN 1 P5V_D_fused +5V (fused) Display VCC 2 P5V_D_fused +5V (fused) Display VCC 3 GND 4 CLK Signal Meaning TFT TFT 1 P5V_D_fused +5V (fused) Display VCC 2 P5V_D_fused +5V (fused) Display VCC 3 GND 4 CLK 5 GND 5 GND 6 LP Horizontal sync 6 HSync Horizontal sync 7 FP Vertical sync 7 VSync Vertical sync 8 - - 8 R0 Signal red bit 0 (LSB) 9 - - 9 R1 Signal red bit 1 10 UD6 Upper data bit 6 10
Hardware Information Release 04/02 Display port (LVDS), X400 TFT displays with an LVDS port can be connected to this port. 18-bit displays having a resolution up to 1024x768 pixels can be connected. The permissible display clock rate is 20 MHz to 66 MHz. The display is selected automatically according to the code of the Display Select inputs. The display supply voltages (3,3 V and 5 V) are connected as a function of the requirements for the connected displays via the graphics controller.
Hardware Information Release 04/02 Assignment of display to display select pins Automatic configuration of one of 15 possible displays is performed by means of the Display Select inputs. The Display Select inputs have pull-up resistors – in other words, if these inputs are not connected, they go to High. The input has to be connected to GND for them to go Low. Pin No.
Hardware Information Release 04/02 I/O interface for front control elements All the signals necessary for the connection of front control elements, in addition to the display and USB ports, are applied to this port. The maximum cable length is 50 cm at a USB data rate of 12 Mbaud. Pin No.
Hardware Information Release 04/02 Internal serial interface COM2 (V.24), X26 This port is connected in parallel to the external COM2 port. Both ports can therefore only be used as alternately. They are assigned such that a 1:1 connection can be established to a 9-pin D-SUB socket when insulation displacement connectors are used. The maximum cable length is 100 cm at a data rate of 9.6 kbaud. 7.5.3 7-24 Pin No.
Hardware Information Release 04/02 2.5” hard disks Internal X4 170h-177h, 1F0h-1F7h, can be disabled IRQ14, IRQ15, edge-triggered 44 pin, 2mm male connector (2.
Hardware Information Release 04/02 DC interface of the power supply 105W The power supply unit has a connector (X2) through which all the signals on the DC side are connected with the motherboard. 7-26 Pin No.
Hardware Information Release 04/02 Interface to floppy disk drive By means of this interface a notebook floppy disk drive may be connected. The maximum connection length of the data cable may not exceed 40cm. Pin No. Short Name Meaning Input/ Output 1 P5V +5V Output 2 INDEX_N Index hole recognition Input 3 P5V +5V Output 4 DS_N0 Drive 0 selection Output 5 P5V +5V Output 6 DCHG_N Disk change display Input 7 n.c. Not assigned - 8 n.c.
Hardware Information Release 04/02 Allocation of IDE intefaces The primary IDE port is designed for alternatively installing 2.5” and 3.5” hard disks. 3.5” drives are connected by means of a 40-pin 2.54 mm pitch connector and 2.5” drives by means of a 44-pin 2 mm pitch connector. The two connectors are connected in parallel. The secondary IDE port is intended for the optional connection of a CD ROM and / or an LS 240 drive. It can be adapted using a 44-pin 2 mm pitch connector.
Hardware Information Release 04/02 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 X41 Meaning RESET GND D7 D8 D6 D9 D5 D10 D4 D11 D3 D12 D2 D13 D1 D14 D0 D15 GND n.c. DREQ GND IOW_N GND IOR_N GND IORDY Reserved DACK_N GND IOCS16 n.c.
Hardware Information Release 04/02 Connection of an LS240 drive The optional LS240 drive is connected via this port. This port is connected in parallel to the secondary IDE port. The connected LS240 drive is automatically master (i.e. bootable drive) as the result of a special RC circuit. The maximum connection length of the data cable may not exceed 40cm. 7-30 Pin No.
Hardware Information Release 04/02 SV connection for hard disk The power supply of the 3.5” hard disk is effected via this connection. Pin No. Short Name Description Input / Output 1 P12V +12 V Output 2 GND Chassis ground – 3 GND Chassis ground – 4 P5V +5 V Output Connection for CPU fan The CPU fan is connected via this connection. Pin No.
Hardware Information Release 04/02 7.6 Wiring Backplane 7.6.1 Design and Theory of Operation The bus board is designed as a passive link between the motherboard and the expansion modules. It is mounted with a screw. The bus board has two ISA slots and two PCI slots, as well as a shared ISA /PCI slot. The power supply to the expansion cards is effected via the connection of the bus unit with the basic board. An external power supply (+5V and +12V) is provided. Figure 7-10 7.6.
Hardware Information Release 04/02 Pin No. *) # Type* Pin No.
Hardware Information Pin Release 04/02 Signal Name Type * Pin Signal Name Type C1 –SBHE O D1 –MEMCS16 I C2 LA 23 I/O D2 –IOCS16 I C3 LA 22 I/O D3 IRQ 10 I C4 LA 21 I/O D4 IRQ 11 I C5 LA 20 I/O D5 IRQ 12 I C6 LA 19 I/O D6 IRQ 13 I C7 LA 18 I/O D7 IRQ 14 I C8 LA 17 I/O D8 –DACK0 O C9 –MEMR I/O D9 DRQ 0 I C10 –MEMW I/O D10 –DACK5 O C11 SD 08 I/O D11 DRQ 5 I C12 SD 09 I/O D12 –DACK6 O C13 SD 10 I/O D13 DRQ 6 I C14 SD 11 I/O
Hardware Information Release 04/02 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 5V System Environment Side B Side A –12V TRST# TCK +12V Ground TMS TDO TDI +5V +5V +5V INTA# INTB# INTC# INTD# +5V PRSNT1# Reserved Reserved +5V (I/O) PRSNT2# Reserved Ground Ground Ground Ground Reserved Reserved Ground RST# CLK +5V (I/O) Ground GNT# REQ# Ground +5V (I/O) Reserved AD[31] AD[30] AD[29] +3.
Hardware Information Release 04/02 Assignment of slot-specific PCI bus signals 7-36 PCI Socket Pin No.
Hardware Information Release 04/02 7.7 Power supply (AC and DC) Technical Data Voltage Max. current Voltage stability +12 V 2.5 A " 4% –12 V 0.3 A " 5% +5V 13.5 A " 3% +3.3 V 8.
Hardware Information 7.8 Release 04/02 Connecting cables SIMATIC S5 Connecting Cable By means of the SIMATIC S5 connecting cable (not included in all supply variants) you can connecto your computing unit with a SIMATIC S5 automation device. Please study the notes in Chapter 3.
Distributed configuration 8 Chapter Overview This chapter describes all specifications of the distributed configuration that are different from those of the integrated configuration (described in chapters 2 – 7). Where this manual focuses on the computing unit. Note The part of the description referring to the Remote mount of the control unit will be found in ”SIMATIC Panel PC 670/870 Control Unit” manual. In chapter 5.
Distributed configuration 8.1 Description 8.1.1 Overview Release 04/02 Figure 8-1 shows a PC 670 computing unit (distributed configuration) with the transmitter fitted between mounting brackets.
Distributed configuration Release 04/02 8.1.2 Dimensions 104,1 8 43.5 25 Figure 8-2 shows the dimensions of the PC 670 computing unit with transmitter. 304.6 74.3 289.6 297.2 211 253 Transmitter Dimensions in mm Figure 8-2 Dimensions computing unit PC 670 without CD-ROM drive in distributed configuration including transmitter 8.1.3 Mounting The computing unit is supplied as a complete combination with the transmitter installed ex works.
Distributed configuration 8.2 Release 04/02 Cable connection Transmitter and receiver are connected by a cable with a maximum length of 20 m. For operation, the angled cable connector is inserted in the socket of the transmitter and locked. The interconnecting cable must also be fixed in position. For further details refer to the ”SIMATIC Panel PC 670/870 Control Unit” manual, Chapter 5. 8.3 Spare parts The following spare parts are available: 8.
Distributed configuration Release 04/02 Computing unit Groove for outer fastening screws Encoder S30 Transmitter housing Transmitter Port for interconnecting cable Center screwhole Figure 8-3 Transmitter in opened transmitter housing 4. Check (or set) the switch setting as shown in the table below: Table 8-1 Display type adjustment via encoder S30 Type Resolutio n S30/4 S30/3 S30/2 S30/1 12” (SVGA) 800 x 600 OFF ON ON ON 15” (XGA) 1024 x 768 OFF ON ON OFF 5.
Distributed configuration 8-6 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Technical Data A In this Appendix This appendix contains the following technical specifications for the Panel PC 670 computing unit: S General Information S Safety S Electromagnetic Compatibility (EMC) S Ambient Conditions S Mechanical environmental conditions S Motherboard S Drives S Graphics card S Interfaces S Function displays (light-emitting diodes) on device Panel PC 670 Computing Unit, Equipment Manual A-1
Technical Data A.1 Release 04/02 Technical Data of the Panel PC 670 Computing Unit General Order nos. See order documentation Dimensions 297x267x80 (WxHxD in mm), without CD-ROM drive 297x267x101 (WxHxD in mm), with CD-ROM drive approx. 6kg (13.5 lbs.) 120 V (85 V to 132 V (AC), or 230 V (170 V to 264 V) AC (autorange) Weight Supply voltage (UN) (Line voltage frequency, AC alternative: 24 V (20.4 bis 28.8 V) DC, SELV 50/60 Hz (47 to 63 Hz) Short-term power interruption complying to to Namur Max.
Technical Data Release 04/02 Environmental conditions Temperature tested to DIN EN 60068-2-2:1994, DIN IEC 60068-2-1, DIN IEC 60068-2-14, – – operation storage/transport +5 °C to +45 °C - 20°C to +60°C – gradient max 10°C/h (no condensation) Relative humidity tested to DIN IEC 60068-2-3, DIN IEC 60068-2-30, DIN IEC 60068-2-56 – – operation storage/transport 5% to 80% at 25°C (no condensation) 5% to 95% at 25°C (no condensation) – gradient max 10°C/h (no condensation) Mechanical environment
Technical Data Graphic Graphic controller Graphic store Resolutions/frequencies/colors Interfaces COM 1 Release 04/02 UXGA LCD controller on the AGP bus bis zu 32 MB SDRAM sind Bestandteil des Hauptspeichers und können konfiguriert werden (8/16/32MB) CRT: up to 1600x1200/85 Hz / 65536 colors with PC133 up to 1280x1024/85 Hz / 65536 colors with PC100 memory modules LPT1 Serial port 1 (V.24 / TTY), 25 pin subminiature Cannon connector Serial port 2 (V.
ESD Guidelines B Chapter Overview In chapter You Will Find on Page B.1 What does ESD mean? B-2 B.2 Electrostatic charge of people B-3 B.
ESD Guidelines B.1 Release 04/02 What does ESD mean? Definition All electronic components are equipped with high-integrated modules or components. Conditioned by their technology, these electronic components are extremely sensitive to overvoltages and therefore to discharges of static electricity. These Electrostatically sensible components/assemblies are internationally known under the abbreviation as ESD.
ESD Guidelines Release 04/02 B.2 Electrostatic Charge of People Charging Anyone who is not conductively connected to the electrical potential of their surroundings can be electrostatically charged. The maximum electrostatic voltage values which an operator can be charged with when contacting the materials stated in the illustration are shown in Fig. B-1. These values correspond to the specifications of IEC 801-2.
ESD Guidelines B.3 Release 04/02 Basic Safety Measures against Discharge of Static Electricity Ensuring a good ground connection When handling electrostatic sensitive devices, ensure that your person, the workplace and packaging are grounded. In this manner you avoid static charge. Avoid direct contact As a general principle, only touch electrostatic sensitive devices when this is unavoidable (e.g. during maintenance work).
SIMATIC HMI Documentation C Target groups This manual is part of the SIMATIC HMI documentation.
SIMATIC HMI Documentation Release 04/02 Documentation Target Group Content First Steps with ProTool Newcomers This documentation guides you step by step through the configuration of Product Brief S a screen with various objects S a change of display and S a message.
SIMATIC HMI Documentation Release 04/02 Documentation Target Group Content Copy Protection Start-up Guide Commissioning engineers, Users The ProTool/Pro Runtime visualization software is a copyright product. This manual contains information on the installation, repair and uninstallation of authorizations. Application Example Newcomers ProTool is supplied with example configurations and the corresponding PLC programs.
SIMATIC HMI Documentation Release 04/02 Documentation Target Group Content Communication Programmers Contains information on connecting line- and graphic-based control panels to the following controls: User’s Guide S S S S SIMATIC S5 SIMATIC S7 SIMATIC 500/505 drivers for other PLCs This documentation describes the S configuration and parameters required for connecting the devices to the PLC and the network S user data areas used for exchanging data between operating unit and PLC.
Glossary A APM Advanced Power Management. Application An application is a program directly linked to the MS-DOS or Windows operating system. Applications on SIMATIC PCs are, for example, the visualization packages SIMATIC ProTool/Pro, SIMATIC WinCC and others. Automation system (AS) A controller in the SIMATIC S7 series (for example, SIMATIC S7-200/300/400). C Cache Buffer between working memory and central processing unit. COM1 port Serial V.24/modem port, 25-pin, sub-D connectors, sockets.
Glossary Release 04/02 Configuration software Configuration software updates the device configuration when modules are fitted. This is done either by copying the configuration files supplied with the device of by manual configuration. D Device configuration The device configuration of a SIMATIC PC contains details about its features and options such as memory capacity, drive types, monitor, network address, etc.
Release 04/02 Glossary Interrupt Discontinuation in the processor of a programmable controller by an interrupt event. IRQ Interrupt request. ISA Industrial Standard Architecture (bus for expansion board) K Keyboard port PS/2 keyboard connector Keyboards with an integrated trackball can be connected. L LPT 1 port The LPT 1 port (Centronics interface) is a parallel interface which can be used for attaching a printer. LS 120 drive The LS 120 drive is compatible with the familiar 3.5” floppy disk drive.
Glossary Release 04/02 MPI/DP port (Multi-Point-Interface/Profibus-DP) for connecting an S7 programmable controller. P Parallel port Information is transferred on a byte by byte basis through a parallel port. High data transfer rates are achieved as a result. SIMATIC PCs have one parallel port (LPT) for attaching a printer. PC card interface For connecting PC cards (types I/II/III). PCI or PCI/ISA slot (Peripheral Component Interconnect) for expansion boards.
Glossary Release 04/02 S SCSI interface Small Computer System Interface. Interface for connecting SCSI devices (for example, hard disks, CD-ROM drives) SETUP (BIOS Setup) A program which defines information about the device configuration. The device configuration of the SIMATIC PC is preset. Changes have to be made when a memory expansion module, new modules or drives have to be activated.
Glossary Glossary-6 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
Index A Bus board, removing and installing, 4-23 Acclimatization, 1-4 APM (Advanced Power Management), 5-24 AT modules, 4-12 C B Backup battery, 3-17 replacement, 4-10 Batteries, 1-7 disposal, 1-7 Battery, 3-17 safety notes, 3-17 Beep Codes, 6-8 BIOS, error messages, 6-6 BIOS Setup, 5-1 call, 5-2 Configure APM, 5-24 Configure COM/LPT, 5-16 Configure interfaces, 5-13 Configure Memory Gap, 5-15 Configure passwords, 5-22 Default settings, 5-29 Floppy disks-Setting up drive type, 5-6 Hard disks-Setting up d
Index Computing unit permissible installation positions, 2-5 , 2-6 printer connection, 3-6 , 3-7 Protection class, A-2 PS/2 keyboard connection, 3-8 PS/2 mouse connection, 3-7 rating plate, 3-5 Reset button, 4-27 Reset button, 3-5 serial mouse connection, 3-8 starting up, 2-1 switching off, 2-8 switching on, 2-8 transportation, 2-9 unpacking, 2-2 VGA interface, 3-4 Connecting cables, 7-38 Connection, 3-22 to programming unit, 3-21 to S5-PLC, 3-19 via MPI/PROFIBUS-DP, 3-23 with S7-PLC, 3-22 Connection , usi
Index Release 04/02 Front interfaces, 3-5 G Graphic, technical data, A-4 Green PC, 5-24 H Hard disk, 3-16 Hard disk drive, 3-16 removing and installing, 4-17 Hardware Information, 7-1 Connecting cables, 7-38 Interfaces and parameters, 7-3 Monitoring functions, 7-6 Power consumption of the system components, 7-2 Power supply (AC and DC), 7-37 System resources, 7-5 Wiring backplane, 7-32 Hardware clock, 3-17 I Industrial Ethernet, 3-25 Installation positions, with centralized design, 2-5 , 2-6 Interfaces
Index Module retainer plates, removing and installing, 4-14 Monitor, 3-4 Monitoring functions, 7-6 Fan monitoring, 7-9 Signals on the front interface, 7-6 SOM (Safecard On Motherboard), 7-6 Temperature monitoring, 7-7 Watchdog, 7-8 Watchdog-monitoring times, 7-8 Motherboard, 4-6 removing and installing, 4-24 replacing the processor, 4-26 Mounting angle, 8-2 Mounting positions, in distributed configuration, 8-3 Mouse PS/2, 3-7 serial, 3-8 MPI/DP Interface, 7-16 MPI/DP interface, 3-22 O Opening the unit, 4-
Release 04/02 Index T Target groups, C-1 Technical data Computing unit, A-2 distributed configuration, 8-4 Graphic, A-4 Interfaces, A-4 Time, setting up, 5-6 Tools, 4-3 Transmitter, distributed configuration, 8-4 Transport, 2-9 TTY- interface, 3-19 U USB Interface, 7-15 USB devices, connection, 3-9 V VGA Interface, 7-18 VGA interface, 3-4 W Watchdog, 7-8 Reactions, 7-8 Wiring backplane, 7-32 X XT modules, 4-12 Panel PC 670 Computing Unit, Equipment Manual Index-5
Index Index-6 Release 04/02 Panel PC 670 Computing Unit, Equipment Manual
