Installation Instructions

ManualsBrandsSiemens ManualsDamper actuatorsOpenAirMC série GMA Actionneur de registre rotatif électrique à ressort de rappel 62 lb-po

Operating Instructions

Document No. 129-287

Rev. 1, October, 1999

Actuator Commissioning Tool

Item Number 129-287, Rev. 100 Page 1 of 8

Product Description

The 985-047 Actuator Commissioning Tool provides

a portable instrument for exercising, calibrating, and

testing resistive, proportional (voltage/current),

floating, and on/off actuators. LED display shows

feedback voltages or output. LEDs indicate

operating mode selection and auxiliary switch

contact closure. The Commissioning Tool combines

accurate and reliable technology in a user-friendly,

yet economical package.

The Commissioning Tool saves on installation time

and is compatible with all Siemens actuators and

most competitors’ models. A plug-in transformer or

24 Vac power supply input enables the

Commissioning Tool to output resistance,

AC voltage, DC voltage, and current for controlling

an actuator. It requires no controller hook-up, which

makes equipment calibration, setup, and adjustment

a quick and easy process.

Figure 1. Actuator Commissioning Tool.

Features and Benefits

• Universal Compatibility

Works with all Siemens actuators, most

competitors’ actuators, and other voltage,

current, or resistance controlled equipment

• Compact Portable Unit

Allows easy handling in the field

• Pushbutton Selectable Output/Feedback

Modes

Gives user a complete testing device. No

separate instruments are required for field

testing

• Digital and LED feedback Displays

Provides user with clearly readable voltage

and auxiliary switch feedback in dimly lit

conditions

• Plug-in Terminal Block Test Lead

Connections

Accommodates easy interchangeability of

multiple sets of test leads

Contents

• Actuator Commissioning Tool

• Plug-in transformer

• Terminal blocks, set of three (extra)

• Carrying case

Required Tools

• Test leads

• 1/8 in. tip flat-blade screwdriver

Product Number

985-047

Summary of content (8 pages)

PAGE 1
Operating Instructions Document No. 129-287 Rev. 1, October, 1999 Actuator Commissioning Tool Product Description The 985-047 Actuator Commissioning Tool provides a portable instrument for exercising, calibrating, and testing resistive, proportional (voltage/current), floating, and on/off actuators. LED display shows feedback voltages or output. LEDs indicate operating mode selection and auxiliary switch contact closure.
PAGE 2
129-287 Operating Instructions Rev. 1, October, 1999 Installation Conventions WARNING CAUTION Personal injury/loss of life may occur if a procedure is not performed as specified. Equipment damage, or loss of data may occur if the user does not follow procedure as specified. The Commissioning Tool also provides additional testing features as follows: Table 2. Additional Testing Features.
PAGE 3
129-287 Operating Instructions Rev. 1, October, 1999 Operation WARNING: Powering a Non-externally Powered Actuator or Control Device CAUTION: Shock Hazard. Disconnect all power supplies to the Commissioning Tool and actuator or control device before wiring to avoid possible electrical shock or equipment damage. Powering Commissioning Tool Equipment Damage Hazard. Controlled equipment loading from Terminals 1 and 2 must be limited to 25 VA maximum. NOTE: CAUTION: Equipment Damage Hazard.
PAGE 4
129-287 Operating Instructions Rev. 1, October, 1999 NOTE: When power is not supplied to the Commissioning Tool, LEDs do not activate. The digital display is not used, and reads zero in this mode. 1. To supply a resistive signal, connect Terminals 3, 4, and 5 (POT WIPER) of the OUTPUTS terminal block to the control inputs of the actuator or device being controlled (Figure 6). Also see the appropriate actuator documentation for wiring application information. Figure 7. Resistive Mode.
PAGE 5
129-287 Operating Instructions Rev. 1, October, 1999 6. Use the rocker switch located on the upper left side of the Commissioning Tool (Figure 9) to adjust the voltage level from 0 to 20 Vdc. The digital display shows the level of the output voltage. (Adjustment increments increase 0.1V during the first five seconds and then increase rapidly after that, allowing for quick adjustment of the output control signal.) 6.
PAGE 6
129-287 Operating Instructions Rev. 1, October, 1999 3. Depress the SELECT MODE pushbutton to activate the floating control mode. A green LED should light and indicate that the floating control mode is active (Figure 13). NOTE: CAUTION: Equipment Damage Hazard. Do not apply signals greater than 30 Vdc or any AC signals to Terminal 7 (DC FEEDBACK) or damage to the Commissioning Tool can result.
PAGE 7
129-287 Operating Instructions Rev. 1, October, 1999 Auxiliary Switch Testing CAUTION: Equipment Damage Hazard. Do not apply power to the switch being tested or to the Commissioning Tool auxiliary switch inputs. The Commissioning Tool provides a signal to the switch contacts being tested. Figure 14. Bias Output. Voltmeter Auxiliary switch testing can be used independently or while supplying a control signal to the field devices. LEDs display auxiliary switch contact closure.
PAGE 8
129-287 Operating Instructions Rev. 1, October, 1999 Specifications Power Requirements Commissioning Tool 24 Vac nominal (20 to 30 Vac) at 50/60 Hz, 3 VA, Class 2 Plug-in Transformer (provided) 120 Vac at 60 Hz Input DC Feedback 0 to 30 Vdc Electrical Connection Screw Terminals 24 to 12 AWG Transformer Jack 0.08 in. (2.11 mm) diameter pin, 0.25 in. (6.