Operating instructions

ManualsBrandsSiemens ManualsIndustrialMICROMASTER

Issue B1 5 System parameters

MICROMASTER 420 Operating Instructions

6SE6400-5AA00-0BP0

Commands and Digital I/O (P0004 = 7)

Par. No. Parametername Default Acc WS QC

r0002 Drive state - 2 - -

r0019 CO/BO: BOP control word - 3 - -

r0052 CO/BO: Status word 1 - 2 - -

r0053 CO/BO: Status word 2 - 2 - -

r0054 CO/BO: Control word 1 - 3 - -

r0055 CO/BO: Control word 2 - 3 - -

P0700[1] Selection of command source 2 1 CT Q

P0701[1] Selection of digital input 1 1 2 CT -

P0702[1] Selection of digital input 2 12 2 CT -

P0703[1] Selection of digital input 3 9 2 CT -

P0704[1] Selection of digital input 4 0 2 CT -

P0719 Selection of cmd. & freq. setp. 0 3 CT -

r0720 Number of digital inputs - 3 - -

r0722 CO/BO: Binary input values - 2 - -

P0724 Debounce time for digital inputs 3 3 CT -

P0725 PNP / NPN digital inputs 1 3 CT -

r0730 Number of digital outputs - 3 - -

P0731[1] BI: Digital output 52:3 2 CUT -

r0747 CO/BO: State of digital outputs - 3 - -

P0748 Invert digital outputs 0 3 CUT -

P0800[1] BI: Download parameter set 0 0:0 3 CT -

P0801[1] BI: Download parameter set 1 0:0 3 CT -

P0840[1] BI: ON/OFF1 722:0 3 CT -

P0842[1] BI: ON/OFF1 reverse 0:0 3 CT -

P0844[1] BI: 1. OFF2 1:0 3 CT -

P0845[1] BI: 2. OFF2 19:1 3 CT -

P0848[1] BI: 1. OFF3 1:0 3 CT -

P0849[1] BI: 2. OFF3 1:0 3 CT -

P0852[1] BI: Pulse enable 1:0 3 CT -

P1020[1] BI: Fixed freq. selection Bit 0 0:0 3 CT -

P1021[1] BI: Fixed freq. selection Bit 1 0:0 3 CT -

P1022[1] BI: Fixed freq. selection Bit 2 0:0 3 CT -

P1035[1] BI: Enable MOP (UP-command) 19:13 3 CT -

P1036[1] BI: Enable MOP (DOWN-command) 19:14 3 CT -

P1055[1] BI: Enable JOG right 0:0 3 CT -

P1056[1] BI: Enable JOG left 0:0 3 CT -

P1074[1] BI: Disable additional setpoint 0:0 3 CUT -

P1110[1] BI: Inhibit neg. freq. setpoint 0:0 3 CT -

P1113[1] BI: Reverse 722:1 3 CT -

P1124[1] BI: Enable JOG ramp times 0:0 3 CT -

P1230[1] BI: Enable DC braking 0:0 3 CUT -

P2103[1] BI: 1. Faults acknowledgement 722:2 3 CT -

P2104[1] BI: 2. Faults acknowledgement 0:0 3 CT -

P2106[1] BI: External fault 1:0 3 CT -