Data Sheet for Product

Siemens Industry, Inc. Page 3 of 13
Specifications
Materials (within air stream) - Standard
Venturi Valve Casing
Cone 0.04” (18 GA)
0.06” Spun aluminum (14 GA)
Airflow Sensor Aluminum orifice
Venturi Cone
assembly
Spun aluminum cone
Teflon-coated dashpot tube
Celenex (PBT) end cap & slider
Stainless steel pressure spring
Cone Rod 3/8-inch (.95 cm) stainless steel
Teflon-coated for corrosive air
Cone Rod Bushings Teflon
Options Epoxy Phenolic coating
for aluminum air stream parts
Materials (outside air stream) – Standard
Control Enclosure Galvanized steel
Pneumatic Tubing UL rated 94 V-2 fire retardant
polyethylene
Flow Sensor Fittings Stainless Steel or Aluminum
Options
External Thermal Insulation
3/4” fiber free foam. Density 1.5
lbs/ft
3
, R=3
Meets NFPA 90A, UL181
Flame Spread rating < 25
Smoke Developed rating < 50
Meets ASTM E84, UL 723, and
bacteria standard ASTM C665
Leakage (Per ASHRAE 130-1996 Method)
Thru Casing At 6”wc
Less than 0.25 cfm/body, all
sizes
Thru Shut-Off
Gaskets
Less than 0.15 cfm/body,
all sizes, all pressures
N510
LIMIT
(%vol/min)
N510
LIMIT
@ 10"
(cfm)
N510
LEAKAGE
@ 10"
(cfm)
N510
LEAKAGE
@ 10"
(%vol/min)
106
0.241 0.10% 0.00024 0.00001 0.01%
108
0.489 0.10% 0.00049 0.00001 0.002%
110 0.795 0.10% 0.00080 0.00005 0.01%
112
1.329 0.10% 0.00133 0.00076 0.06%
SIZE
SIEMENS AVZ CASING LEAKAGE PER ANSI/ASME N510
AVZ
VOLUME
(FT3)
* Results of tests performed August, 2008. Report available upon request.
NOT TO EXCEED ACTUAL RESULTS*
Figure 3. Casing Leakage by ANSI/ASME N510 Method.
Weight 20 - 32 lbs (9.1 – 14.5 kg)
Environmental
Operating
Temperature/% RH
40°F to 120°F (4°C to 49°C)
0% to 95% RH non-condensing
Storage
Temperature/% RH
-10°F to 150ºF (-23°C to 65°C)
0% to 95% RH non-condensing
Airflow Control Electronic Actuation
High-Speed Electric Full stroke in < 2.0 sec. Max
thrust 50 lb
One for singles, duals
Standard Speed
Electronic
Spring Return:
62 lb-in singles, duals and triples
Fail-in-last-position:
Singles - 44 lb-in
Multiples – 88 lb-in
Flow Measurement
Sensor Type Integral Orifice sensor
Sensor Accuracy Sensor error < 2% of signal.
Total Flow measurement error <
±5% above 350 fpm duct
velocity.
Installation
Requirements
No special inlet or outlet
conditions required to maintain
pressure independence.
For best airflow measurement
results, provide at the inlet at
least one equivalent diameter of
straight duct, or a transition with
less than 30 degree taper.
Support adjoining ducts within
12” of the air valve.
Figure 4. Shut-off & Casing Leakage Size 112 N510 Method.