Installation Instructions

ManualsBrandsSiemens ManualsRoom controlsRoom Condition Monitor, RPM series

Document No. 546-00085

December 8, 2011

CE Compliant Fume Hood Controller —

Application 941 and 942

Item No. 546-00085. Rev. CA Page 1 of 7

Figure 1. CE Compliant Fume Hood

Controller(Standard enclosure).

Figure 2. CE Compliant Fume Hood Controller

(Otherenclosure).

Control Applications

941 and 942

Product Description

The Fume Hood Controller Board (Figure 1 and

Figure 2) is the main termination board for the Fume

Hood Controller. The board comes with a ferrite filter

to suppress electrical emissions from the 8-

conductor cable. The ferrite filter must be installed to

meet FCC requirements and CE compliance

Product Numbers

546-00705

CE Compliant Fume Hood Controller

— Application 941 and 942 with cover

and mounting rail

546-00705E

CE Compliant Fume Hood Controller

— Application 941 and 942 with FHC

enclosure

NOTE:

Keep the controller board in its static

proof bag until you are ready to install.

Warning/Caution Notation

WARNING

Personal injury/loss of life may

occur if you do not follow the

procedures as specified.

CAUTION

Equipment damage or loss of data

may occur if you do not follow the

procedures as specified.

Expected Installation Times

23 minutes.

Required Tools and Materials

• Smallflat-blade screwdriver

Prerequisites

• Fume Hood Controller Enclosure is mounted

and wiring has been roughed-in.

• Operator Display Panel is installed and

cable pulled to location of controller.

Summary of content (7 pages)

PAGE 1
Installation Instructions Document No. 546-00085 December 8, 2011 CE Compliant Fume Hood Controller — Application 941 and 942 Product Numbers 546-00705 546-00705E CE Compliant Fume Hood Controller — Application 941 and 942 with cover and mounting rail CE Compliant Fume Hood Controller — Application 941 and 942 with FHC enclosure NOTE: Keep the controller board in its static proof bag until you are ready to install. Warning/Caution Notation Figure 1.
PAGE 2
Document No. 546-00085 Installation Instructions December 8, 2011 Instructions 1. If the Fume Hood Controller will be used with a ﬁeld panel, then disconnect the Field Level Network (FLN) trunk from the ﬁeld panel. 2. Place the ESD wrist strap on your wrist and attach it to a good earth ground. 3. Carefully remove the controller board from the anti-static bag. 4.
PAGE 3
Document No. 546-00085 Installation Instructions December 8, 2011 10. Plug the Operator Display Panel cable into the Operator Display Panel Communication port on the controller board (Figure 6 and Figure 7). NOTE: The ferrite filter must be installed on the cable inside the enclosure to meet FCC and CE requirements (Figure 6). Figure 5. Installing a Ferrite Filter. Figure 6. Ferrite Filter Installed. The installation is complete. Siemens Industry, Inc.
PAGE 4
Document No. 546-00085 Installation Instructions December 8, 2011 Figure 7. Fume Hood Controller with Damper Wiring (Application 941). Page 4 of 7 Siemens Industry, Inc.
PAGE 5
Document No. 546-00085 Installation Instructions December 8, 2011 Figure 8. Fume Hood Controller with Venturi Air Valve Wiring (Application 942). Siemens Industry, Inc.
PAGE 6
Document No. 546-00085 Installation Instructions December 8, 2011 NOTE: The wiring shown is based on wiring sashes from the left side. When wiring sashes from the right, the wiring is reversed. The sash closest to the connector is wired to Red and Black. The sash farthest from the connector is wired to White and Black. Figure 11. Four Horizontal Sash Configuration. Figure 9. Single Vertical Sash Configuration. Figure 12. Two Horizontal/One Vertical Sash Configuration. Figure 10.
PAGE 7
Document No. 546-00085 Installation Instructions December 8, 2011 Figure 14. 2 Verticals and up to 8 Horizontals, Walk-in Sash Configuration Wiring Diagram. Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. APOGEE and Insight are registered trademarks of Siemens Industry, Inc. Other product or company names mentioned herein may be the trademarks of their respective owners.