Installation Instructions

Document No. 541-865
Installation Instructions
Rev. 4, March, 2000
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and
models as design improvements are introduced. Insight
for Minicomputers is a registered trademark of Siemens Building Technologies, Inc. ©
2000 Siemens Building Technologies, Inc.
Siemens Building Technologies, Inc.
Landis & Staefa Division
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
U.S.A.
Document No. 541-865.
Printed in the U.S.A.
Page 9 of 10
CON = Console
;COM /Port:2/Flow:XON = Console /Mode:9600
;TT0
10. The startup code displays a menu of options
after it receives ESC.
=============================================================
Osprey Startup/Bootstrap Menu
Disk Ctlr Drives Tape Ctlr Drives
----------------------------------------- ----------------------
1.. MSCP RAxx,RC25,RD5x,RX33,RX50 21.. TMSCP
TK50,TU81E
2.. RH11/RH70 RP04/5/6/7,RM02/3/5/80,RS03/4 22.. TS11/TSV11
TSV05,TU80
3.. RL11/RLV11 RL01,RL02 23.. TM11/TMA11 TE10,TU10
4.. RX11 RX01
5.. RX211 RX01,RX02
6.. RK611/RK711 RK06,RK07
7.. RK11 RK05,RK05F
8.. FWDx106 RX01/2, various hard drives
Please enter option: [21.]
=============================================================
11. Enter option
21
for TMSCP at the prompt. Next,
boot procedures will prompt for a base address
and unit number. The defaults are shown in
square brackets.
=================================================
Enter controller address..... [174500]
Enter unit number............ [0.]
=================================================
12. Press
<RETURN>
to accept both defaults. The
Osprey Co-Processor will now boot RSX from
the MU: device (SyQuest drive).
13. The minicomputer begins to boot. When it is
finished, the system displays the following
prompt:
Valid switches are:
/CSR=nnnnnn to change the default
device CSR
/VEC=nnn to change the default
device vector
/FOR=n to change the default magtape
formatter number
/DEV to list all default device CSR
and vectors
Enter first device:
14. Enter the CSR and vector addresses for the first
device by typing
MU:/CSR=174500/VEC=260
and press
<RETURN>
.
The system prompts you for the second device:
Enter second device:
15. Enter the CSR and vector addresses for the
second device by typing:
DU:/CSR=172150/VEC=154
and press
<RETURN>
.
The following time prompt displays:
Hit RETURN and enter date and time as
’TIM HH:MM MM/DD/YY’
Do not respond to the time prompt until you are
instructed to do so (in Step 15). Continue this
procedure with Step 13 now.
16. Remove the loading tape by pressing the green
button on the SyQuest drive.
17. You are now ready to load the Revision K.0
system from the SyQuest drive to the hard disk.
Insert the Revision K.0 Master tape in the drive.
18. Respond to the time prompt (displayed in Step
12) by entering the time and date. Use the
following format:
TIM HH:MM MM/DD/YY <RETURN>
where:
HH = hours 00 through 23 (24 hour clock)
MM = minutes 00 through 59
DD = day 01 through 31
MM = month 01 through 12
YY = year 98, 99, 00, etc.
Be sure to enter the colons (:) between the
hours and minutes, a space between the time
and date, and slashes (/) between the day,
month, and year.
19. At the MCR prompt, type
RUN BRU
and press
<RETURN>
.
The BRU prompt (BRU>) displays.
20. At the BRU prompt, type
/INI/VER/REW MU0: DU0:
and press
<RETURN>
.