s Hotel Solution™ HMI User's guide CM2B6307en 12/15/2008 For internal use only Building Technologies
Siemens Switzerland Ltd Building Technologies Group International Headquarters Gubelstrasse 22 CH-6301 Zug Tel. +41 41-724 24 24 Fax +41 41-724 35 22 www.siemens.
Content 1 About this document ..............................................................................4 1.1 Revision history.........................................................................................4 1.2 Reference documents ...............................................................................4 1.3 Before you start.........................................................................................4 1.4 Target audience...............................................
1 About this document 1.1 Revision history Version Date Changes Section Pages 1.1 03.11.2008 1.0 30.09.2008 Added RoomOverview Corrected figure First draft 3.1, 3.2, 3.4 3.5 All 6, 7, 9 10 All 1.2 Reference documents Ref. Document title Document type [1] [2] Hotel Solution – System software Hotel Solution – User interface Installation and configuration instructions User's guide 1.
We assume that persons using our products and documents are authorized and properly trained and have the requisite technical knowledge to use our products as intended. If lack of clarity or other problems associated with the use of the documents persist, do not hesitate to contact the Product Manager at your nearest branch office, or the support team. Email: fieldsupport-zug.ch.sbt@siemens.
3.1 First page. The first page of the HMI provides the address settings for the room controller. HRC3.1 HRC3.2 Parameter Description HMI version Act.Addr New Addr EIB HMI template version number. Current address for the controller. Setting for the new controller address. State of the KNX bus controller on the controller. This parameter is not available for HRC3.2. OK = Bus connection is OK. Err = Bus connection error. Possible causes: – KNX bus is not connected. – No bus power supply.
3.2 Diagnostics. Diagnostics is used to troubleshoot the room controller. Simulate Simulation = Simulation mode is enabled. The controller inputs and outputs are separated from the application and the controller goes into simulation mode. It is now possible to switch outputs in a defined manner via additional parameters. This allows for trouble shooting the room (e.g. for wiring mistakes). The active inputs can be read in this mode. Normal mode = The controller is in normal operation.
3.3 Information The page provides information on the application on the controller. Parameters Description Date ApVers OSVers P-Name P-Version back Creation date. Displays application version. Displays OS version. Displays project name. Displays project version. Back to Diagnostics page. 8 / 14 Siemens Building Technologies Can this field be edited? No. No. No. No. No. No.
3.4 Room Overview. This HMI page provides the basic data on the room controller. Parameters Description Reader This parameter displays the active, correctly configured and parameterized card readers on the controller. 1 = Card reader active and without error. 0 = No card reader connected/active or the wrong address is set on the card reader. This parameter displays the active, correctly configured and parameterized card holder on the controller. 1 = Card holder active and without error.
3.5 Digital inputs active Conducts wiring test at the input. Only one input is tested for this overview. The figure below for the HRC3.1 controller displays two active inputs: DI6 und DI15. The parameter HowManyAct indicates how many inputs are currently active. HRC3.1 HRC3.2 Parameter Description All as Dec Displays active inputs as a decimal number. A recalculation is possible here to determine which inputs are currently active. The display is only there to determine changes.
Parameter Description Can this field be edited? (HRC3.1 only) Caution: Only the last active input is displayed when two inputs are active in the range DI 01 – DI 09. Which is why only one input is active for testing purposes. This can be viewed in the parameter HowManyAct. HowManyAct Note: This parameter exists for the HRC3.1 only. Displays the number of active inputs. Only one input may be active in each range (Act 01 – 09 / Act 10 – 16) for a correct display of the active inputs. No.
3.6 Switch Outputs Conducts wiring test at the output. Each output can be switched individually. The parameter Simulate (Diagnostics page) must be set to Simulation to use this page. The outputs are reset when an output is changed using the HMI and simulation is set to normal operation. Parameters Description Switch RL HRC3.1: Switch on relay RL1-RL8. HRC3.2: Switch on relay RL1-RL5. HRC3.1: Switch on relay RH4-RH9. HRC3.2: Switch on relay RH4-RH7. HRC3.1: Switch on relay DO1-DO8. HRC3.
For internal use only Siemens Building Technologies 13 / 14 HMI Display and operating pages CM2B6307en 12/15/2008
Siemens Switzerland Ltd Building Technologies Group International Headquarters Gubelstrasse 22 CH-6301 Zug Phone +41 41-724 24 24 Fax +41 41-724 35 22 www.siemens.
