Data Sheet for Product

ManualsBrandsSiemens ManualsBuilding automationHow can your guests enjoy the highest standard of comfort without compromising the environment?

332

HOTEL SOLUTION™

Chipcard reader

HCR3.2/..

Chipcard reader for hotel room access control

• Reads access code on chipcard

• Transfers access code to room controller

• Built-in optical display of messages from hotel room

• Messages indicated by LEDs above imprinted symbols

• Membrane switch for doorbell feature

• Illuminated card slot

Application

The HCR3.2 chipcard reader is used in conjunction with the HRC3.1 and HRC3.2 room

controllers.

Guest and hotel-staff access codes are read by the HCR3.2 chipcard reader and

transmitted to the HRC3.1/HRC3.2 room controller for access control.

CM2N6332en

01.09.2008

Building Technologies

Summary of content (8 pages)

PAGE 1
s 6 332 HOTEL SOLUTION™ HCR3.2/.. Chipcard reader Chipcard reader for hotel room access control • Reads access code on chipcard • Transfers access code to room controller • Built-in optical display of messages from hotel room • Messages indicated by LEDs above imprinted symbols • Membrane switch for doorbell feature • Illuminated card slot Application The HCR3.2 chipcard reader is used in conjunction with the HRC3.1 and HRC3.2 room controllers. Guest and hotel-staff access codes are read by the HCR3.
PAGE 2
Function The HCR3.2 chipcard reader communicates with the HRC3.1/HRC3.2 room controller via a serial port, performing the following functions: • Reads the access code on a chipcard • After reading it, transfers the access code to the HRC3.1/HRC3.2 room controller • Activates the functions programmed in the HRC3.1/HRC3.2 room controller based on the access code concerned (guest code, hotel staff code, invalid code).
PAGE 3
Mechanical design Construction The chipcard reader consists of: • Component assembly (carrier, printed circuit board, four LEDs, membrane switch, chipcard reader-unit, terminal block and DIP switch) • Base frame: − Bticino Living/Type L4703 for HCR3.2/BB − Bticino Light/Type N4703 for HCR3.2/BW − Vimar Idea/Type 16713 for HCR3.2/VB − Vimar Plana or Ikon/Type 20613 for HCR3.2/VW The component assembly is permanently glued into the base frame and cannot, therefore, be replaced.
PAGE 4
Rear view 1 RS485+ 2 RS485- 3 DC 12 V 4 DC 0 V 6332Z02de 4 3 ADR0 ADR1 PROT TERM ON Key STOP Important note 3 DIP switches 4 Terminal block • Bus address setting (ADR0, ADR1) • Protocol setting − PROT = 0, for HRC3.1/HRC3.2 room controller − PROT = 1, for HRC3.
PAGE 5
Mounting instructions • The HCR3.2 chipcard reader must be mounted outside the hotel room at the same height as the light switch. • Ensure that there is enough spare cable in the mounting box to allow operation of the address switches on the PCB. • The device is intended for fixed installation in a dry, enclosed space. • For installation in a 3-module mounting box, depth 50 mm. • Must be mounted horizontally with the front plate vertical. • Do not install AC 230 V devices in the same mounting box.
PAGE 6
Technical data Power supply (from HRC3..
PAGE 7
3 4 1 2 3 4 S2 1 2 3 4 Serial port, RS485 + Serial port, RS-485 – DC 12 V operating voltage DC 0 V operating voltage S2 N1 HCR3.2 chipcard reader HRC3.1 room controller S2 N1 HCR3.2 chipcard reader HRC3.2 room controller 6332A01 HCR3.2 connection diagram 2 6332G01 1 (GND) Connection terminals (DC 12 V) Connection diagrams 1 2 3 4 X12 N1 1 2 3 4 S2 6332A02 HCR3.2 connection diagram 1 2 3 4 X3 N1 7/8 Building Technologies HCR3.2/.. - Chipcard reader CM2N6332en 01.09.
PAGE 8
Dimensions HCR3.2/BB Dimensions in mm Diagram and dimensions of Bticino frame L4703. HCR3.2/VB Dimensions in mm Diagram and dimensions of Vimar frame 16713. 47 6332M01 72 115 118 111,8 48 6332M02 75 67 0,9 90,6 4 9 Note See the frame supplier documentation for dimensions of other frames and hole spacing (Bticino, Vimar). 8/8 © 2006-2008 Siemens Switzerland Ltd Building Technologies HCR3.2/.. - Chipcard reader Subject to change CM2N6332en 01.09.