Operation Manual

Gi
gaset
DA
710
/
en
/
A
30350-
M
213-
R
101-2-7
W
19
/
appen
di
x.
f
m
/
19.07.2012
de en fr nl 15
1110-01
Appendix
Other settings
In addition to the options described in section Adjusting the tele-
phone (
£ page 11), you can perform further settings with the help of
Feature codes (e.g. reset the factory settings). These are summarised in
the following table.
Default settings are displayed in bold. If there is no bold value for a set-
ting, the presetting is country-dependent.
M  Press the menu key and 1.
~ Enter the key sequence for the Feature code and confirm
with
[.
Predefined key combinations
The following key combinations are predefined for the activation/deac-
tivation of network services.
<number> This will be replaced by the phone number, which has
been specified for the corresponding function in the
menu CLASS (
£ page 13).
Key
sequence
Value Description
02 0
1
2
1 s
3 s
6 s
Sets the length of the pause that
can be inserted with the pause key
25 0
1
2
3
4
Restores all settings to the factory settings
Deletes the contents of all programmable direct dial keys
Deletes all dialling codes
Restores all network service codes
Deletes all stored numbers (not phonebook)
50 0
1
2
Time display off
24 hour format
12 hour format
Sets the time format
57 0
1
2
Deactivate
500 ms/500 ms
30 ms/70 ms
Interval for the LED (hands-free/
headset key) on incoming call
70 0
1
Deactivate
Activate
Eliminates click tone at the begin-
ning or end of ringer.
If network transmits only a very
short ringer impuls, the click tone
can be prevented by deactivating
(setting 0) the setting.
83 0
1
2
Deactivate
Activate
Automatic
Withholds the first ringer. With this
setting, it is possible to determine,
if an incoming call comes from a VIP
number, and to select a VIP ring
tone instead of the normal ring
tone.
88 1~9
B
Settings 1-11
1 = minimum contrast
5 = default setting
11 = maximum contrast
Sets the contrast of the display.
Setting 10: Direct dial key 1
Setting 11: Direct dial key 2
91 0
1
1,5 : 1
2 : 1
Sets the pulse ratio for pulse dial-
ling
92 0
1
2
3
4
85 / 85 ms
85 / 110 ms
85 / 140 ms
110 / 110 ms
70 / 70 ms
Sets signal time/signal pause for
tone dialling
#2 0
1
Activate
Deactivate
Updates time automatically accor-
ding to CLIP information
#4 0
1
Ringer
AC
Start signal for CLIP recognition.
If CLIP does not function with the
default setting 0, select setting
"AC".
#6 3~9
B
Seconds
Settings 3-15
Default setting: 8
Time for termination of an inco-
ming call
Settings 10-15: Press the direct dial
keys 1-5.
Function Key combination
Activate call forwarding for all calls (CFU) *21*<number>#
Deactivate call forwarding for all calls #21#
Activate call forwarding when no reply (CFNR) *61*<number>#
Deactivate call forwarding when no reply #61#
Activate call forwarding when busy (CFB) *67*<number>#
Deactivate call forwarding when busy #67#
Activate signalling for call waiting (CW) *43#
Deactivate signalling for call waiting #43#
Activate hotline *53*<number>#
Deactivate hotline #53#
Key
sequence
Value Description