Installation Instructions

ManualsBrandsSiemens ManualsDamper actuatorsGDEGLB OpenAir Electronic Damper Actuator, GDB / GLB Rotary, Non Spring Return Installation Instructions

Table Of Contents

WARNING:

Document No. 129-386

October 2, 2009

OpenAir™ GDE Series, Non-Spring Return Electronic Damper

Actuator , Rotary with Terminal Strip

Item Number 129-386, Rev. 012 Page 1 of 5

a. Actuator

b. Position indicator

c. Mounting bracket

d. Mounting screws

e. 4 mm hex key

f. Shaft insert for use with

3/8-inch (8-10 mm)

shafts

Figure 1. Parts of the GDE Rotary Actuator.

Product Description

Steps for direct-coupled mounting of the OpenAir

electronic damper actuator GDE Series non-spring

return rotary with terminal strip.

Product Numbers

GDE131.1T

GDE131.1T/B (24 pk)

GDE161.1T

GDE161.1T/B (24 pk)

Required Tools

• 4 mm hex wrench

• 4 mm (5/32-inch) drill bit and drill

• Small flat-blade screwdriver

• Marker or pencil

Estimated Installation Time

30 minutes

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not follow a

procedure as specified.

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow a procedure as

specified.

Instructions

WARNING:

Do not open the actuator.

NOTE: Place the actuator on the damper shaft

so that the front of the actuator is

accessible. The label is on the front side.

1. Determine whether the damper blades will rotate

clockwise or counterclockwise to open.

See Figure 2.

2. If the blades will rotate counterclockwise, slide the

manual override switch to manual, and move the

adjustment lever to the right. Return the switch to

automatic. See Figure 9.

GDE161.1T

To mount a (modulating) GDE161.1T, set the Dual In-

line Package (DIP) switches to the required positions.

1. To access the DIP switches, raise the tab on

the lower left side of the actuator. See Figure

2. The factory setting is clockwise (middle

switch), with a direct-acting feedback signal

(right switch).

2. Close the tab over the DIP switches.

GDE131.1T

To mount a (3-position) GDE131.1T for counter-

clockwise rotation, follow the Counterclockwise

Damper Rotation instructions located in the Wiring

Diagrams section when wiring the actuator to the

controller.

Summary of content (5 pages)

PAGE 1
Installation Instructions Document No. 129-386 October 2, 2009 OpenAir™ GDE Series, Non-Spring Return Electronic Damper Actuator , Rotary with Terminal Strip a. Actuator b. Position indicator c. Mounting bracket d. Mounting screws e. 4 mm hex key f. Shaft insert for use with 3/8-inch (8-10 mm) shafts Figure 1. Parts of the GDE Rotary Actuator. Product Description Steps for direct-coupled mounting of the OpenAir electronic damper actuator GDE Series non-spring return rotary with terminal strip.
PAGE 2
Document No. 129-386 Installation Instructions October 2, 2009 2. A 3/8-inch shaft adapter is provided in actuator package. 3. Hold the shaft insert so that the raised tabs are inserted last when placing the insert into the back of the actuator. 4. Proceed to Figure 6. When using a 5/8-inch shaft: Figure 2. Setting the Direction of Rotation. NOTE: For DIP switch setting options, see the Technical Instructions EA GDE/GLB-1 (155-187P25). Figure 5. 5/8-inch Ø Shaft.
PAGE 3
Document No. 129-386 Installation Instructions October 2, 2009 1. Loosen the stop set screw. 2. Move it along the track to the desired position, and fasten it in place. Mechanical range limitation and self–adapt feature Figure 8. Attaching the Mounting Bracket. Manual Override 1. To use the entire 0 to 10V input signal to control the adjusted range, raise the tab located on the lower left-hand side of the actuator and locate the DIP switches. See Figure 2. 2. Set the self-adapt DIP switch to 3.
PAGE 4
Document No. 129-386 Installation Instructions October 2, 2009 WARNING: Installations requiring Conformance • All wiring for CE rated actuators must only be separated extra low voltage (SELV) or protective extra low voltage (PELV) per HD384-4-41. • Use safety-isolating transformers (Class III transformer) per EN 61558. They must be rated for 100% duty cycle. • Over current protection for supply lines is maximum 10A. GDE131.1T Counterclockwise Damper Rotation of GDE131.
PAGE 5
Document No. 129-386 Installation Instructions October 2, 2009 Dimensions Figure 15. Dimensions of the OpenAir GDE Actuator with Terminal Strip and Mounting Bracket in Inches (mm).