Operating Instructions

ManualsBrandsSiemens ManualsVariable Speed DriveEU-Declaration of Conformity, SINAMICS G120

461

462

463

464

465

466

467

468

469

470

Parameters

Command and drive data sets - overview

1-470

SINAMICS G120 CU230P-2 Control Units List Manual (LH9), 01/2013

p1521[0...n] CO: Torque limit lower / M_max lower

p1530[0...n] Power limit motoring / P_max mot

p1531[0...n] Power limit regenerative / P_max gen

p1553[0...n] Stall limit scaling / Stall limit scal

p1570[0...n] CO: Flux setpoint / Flex setp

p1574[0...n] Voltage reserve dynamic / U_reserve dyn

p1580[0...n] Efficiency optimization / Efficiency opt.

p1582[0...n] Flux setpoint smoothing time / Flux setp T_smth

p1584[0...n] Field weakening operation flux setpoint smoothing time / Field weak T_smth

p1596[0...n] Field weakening controller integral-action time / Field_ctrl Tn

p1610[0...n] Torque setpoint static (SLVC) / M_set static

p1611[0...n] Supplementary accelerating torque (SLVC) / M_suppl_accel

p1616[0...n] Current setpoint smoothing time / I_set T_smooth

p1654[0...n] Curr. setpoint torque-gen. smoothing time field weakening range / Isq_s T_smth FW

p1703[0...n] Isq current controller pre-control scaling / Isq_ctr_prectrScal

p1715[0...n] Current controller P gain / I_ctrl Kp

p1717[0...n] Current controller integral-action time / I_ctrl Tn

p1730[0...n] Isd controller integral component shutdown threshold / Isd_ctr I_compDeac

p1731[0...n] Isd controller combination current time component / Isd ctrl iCombi T1

p1740[0...n] Gain resonance damping for encoderless closed-loop control / Gain res_damp

p1745[0...n] Motor model error threshold stall detection / MotMod ThreshStall

p1749[0...n] Motor model increase changeover speed encoderless operation / Incr n_chng no enc

p1750[0...n] Motor model configuration / MotMod config

p1755[0...n] Motor model changeover speed encoderless operation / MotMod n_chgSnsorl

p1758[0...n] Motor model changeover delay time closed/open-loop control / MotMod t cl_op

p1759[0...n] Motor model changeover delay time open/closed-loop control / MotMod t op_cl

p1764[0...n] Motor model without encoder speed adaptation Kp / MotMod woE n_adaKp

p1767[0...n] Motor model without encoder speed adaptation Tn / MotMod woE n_adaTn

p1774[0...n] Motor model offset voltage compensation alpha / MotMod offs comp A

p1775[0...n] Motor model offset voltage compensation beta / MotMod offs comp B

p1780[0...n] Motor model adaptation configuration / MotMod adapt conf

p1784[0...n] Motor model feedback scaling / MotMod fdbk scal

p1785[0...n] Motor model Lh adaptation Kp / MotMod Lh Kp

p1786[0...n] Motor model Lh adaptation integral time / MotMod Lh Tn

r1787[0...n] Motor model Lh adaptation corrective value / MotMod Lh corr

p1800[0...n] Pulse frequency setpoint / Pulse freq setp

p1802[0...n] Modulator mode / Modulator mode

p1803[0...n] Maximum modulation depth / Modulat depth max

p1806[0...n] Filter time constant Vdc correction / T_filt Vdc_corr

p1820[0...n] Reverse the output phase sequence / Outp_ph_seq rev

p1959[0...n] Rotating measurement configuration / Rot meas config

p2140[0...n] Hysteresis speed 2 / n_hysteresis 2

p2141[0...n] Speed threshold 1 / n_thresh val 1

p2142[0...n] Hysteresis speed 1 / n_hysteresis 1

p2149[0...n] Monitoring configuration / Monit config

p2150[0...n] Hysteresis speed 3 / n_hysteresis 3

p2153[0...n] Speed actual value filter time constant / n_act_filt T

p2155[0...n] Speed threshold 2 / n_thresh val 2

p2156[0...n] On delay comparison value reached / t_on cmpr val rchd

p2161[0...n] Speed threshold 3 / n_thresh val 3

p2162[0...n] Hysteresis speed n_act > n_max / Hyst n_act>n_max

p2163[0...n] Speed threshold 4 / n_thresh val 4

p2164[0...n] Hysteresis speed 4 / n_hysteresis 4