Operating Instructions

ManualsBrandsSiemens ManualsVariable Speed DriveEU-Declaration of Conformity, SINAMICS G120

471

472

473

474

475

476

477

478

479

480

Command and Drive Data Sets – Overview

Parameters

1-475

SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 06/2011

p1750[0...n] Motor model configuration / MotMod config

p1755[0...n] Motor model changeover speed encoderless operation / MotMod n_chgSnsorl

p1758[0...n] Motor model changeover delay time closed/open-loop control / MotMod t cl_op

p1759[0...n] Motor model changeover delay time open/closed-loop control / MotMod t op_cl

p1764[0...n] Motor model without encoder speed adaptation Kp / MotMod woE n_adaKp

p1767[0...n] Motor model without encoder speed adaptation Tn / MotMod woE n_adaTn

p1774[0...n] Motor model, offset voltage compensation alpha / MotMod offs comp A

p1775[0...n] Motor model, offset voltage compensation beta / MotMod offs comp B

p1780[0...n] Motor model adaptation configuration / MotMod adapt conf

p1784[0...n] Motor model feedback scaling / Mod_FB_scal

p1785[0...n] Motor model Lh adaptation Kp / MotMod Lh Kp

p1786[0...n] Motor model Lh adaptation integral time / MotMod Lh Tn

r1787[0...n] Motor model Lh adaptation corrective value / MotMod Lh corr

p1795[0...n] Motor model kT adaptation integral time / MotMod kT Tn

r1797[0...n] Motor model kT adaptation corrective value / MotMod kT corr

p1800[0...n] Pulse frequency setpoint / Pulse freq setp

p1802[0...n] Modulator mode / Modulator mode

p1803[0...n] Maximum modulation depth / Modulat depth max

p1806[0...n] Filter time constant Vdc correction / T_filt Vdc_corr

p1820[0...n] Reverse the output phase sequence / Outp_ph_seq rev

p1959[0...n] Rotating measurement configuration / Rot meas config

p2140[0...n] Hysteresis speed 2 / n_hysteresis 2

p2141[0...n] Speed threshold 1 / n_thresh val 1

p2142[0...n] Hysteresis speed 1 / n_hysteresis 1

p2149[0...n] Monitoring configuration / Monit config

p2150[0...n] Hysteresis speed 3 / n_hysteresis 3

p2152[0...n] Delay for comparison n > n_max / Del n > n_max

p2153[0...n] Speed actual value filter time constant / n_act_filt T

p2155[0...n] Speed threshold 2 / n_thresh val 2

p2156[0...n] On delay, comparison value reached / t_on cmpr val rchd

p2157[0...n] Speed threshold 5 / n_thresh val 5

p2158[0...n] Delay for n_act comparison with speed threshold value 5 / Del compar n_5

p2159[0...n] Speed threshold 6 / n_thresh val 6

p2160[0...n] Delay for n_act comparison with speed threshold value 6 / Del compar n_6

p2161[0...n] Speed threshold 3 / n_thresh val 3

p2162[0...n] Hysteresis speed n_act > n_max / Hyst n_act>n_max

p2163[0...n] Speed threshold 4 / n_thresh val 4

p2164[0...n] Hysteresis speed 4 / n_hysteresis 4

p2166[0...n] Off delay n_act = n_set / t_del_off n_i=n_so

p2167[0...n] Switch-on delay n_act = n_set / t_on n_act=n_set

p2170[0...n] Current threshold value / I_thres

p2171[0...n] Current threshold value reached delay time / t_del I_thresh rch

p2172[0...n] DC link voltage, threshold value / Vdc thresh val

p2173[0...n] DC link voltage comparison delay time / t_del Vdc

p2174[0...n] Torque threshold value 1 / M_thresh val 1

p2175[0...n] Motor locked speed threshold / Mot lock n_thresh

p2176[0...n] Torque threshold value comparison delay time / M_thrsh comp T_del

p2177[0...n] Motor locked delay time / Mot lock t_del

p2178[0...n] Motor stalled delay time / Mot stall t_del

p2179[0...n] Output load identification current limit / Outp_ld iden I_lim

p2180[0...n] Missing output load delay time / No load t_delay

p2181[0...n] Load monitoring response / Load monit resp

p2182[0...n] Load monitoring speed threshold value 1 / n_thresh 1