User guide

ManualsBrandsSiemens ManualsComputer equipmentERTEC EB 200

The download operation is now complete, and the communication between controller and device is automatically

started.

Following outputs are displayed on the terminal:

Link status

information

Infos about

PROFINET IO

communication

(e.g RT Class 1)

Number of

modules

and

modulinformation

End of

parameterization

Write record

0x10000 with data

length = 8

Start of cyclic date

exchange

link port1: Status=1, Speed=2, Mode=2

Bsp_SetIpAddr (Ip = cb14a8c0h, Subnet = ffffffh, DefRouter = cb14a8c0h,

remanent = 0)

##note only: new IP address = cb14a8c0h, Subnet mask = ffffffh, Default router

= cb14a8c0h

*** AR-CHECK_IND: RT AR ***

ArNum = 1, Session = 1 ArType = 0x1, ArProp = 0x11, NumofApi = 1

Device Hndl = 1, HostIP = 192.168.20.201

StationName = pn-io, Length = 5

********** new RT Class 1 connection **********

AR-INFO_IND new ArNum=1 Session=1, NumOfIocr = 2

IOCR 0: IocrProp = 0x1, Direction=1, SendClk = 32 RedRatio = 1,

NumOfApiObjects = 1

IOCR 1: IocrProp = 0x1, Direction=2, SendClk = 32 RedRatio = 1,

NumOfApiObjects = 1

Number of Api's = 1

Number of Modules = 3

Module plugged; Api = 0, Slot = 0, ModID = 0x2, Subslot = 1, SubId = 0x1

Module plugged; Api = 0, Slot = 0, ModID = 0x2, Subslot = 32768, SubId = 0x1

Module plugged; Api = 0, Slot = 0, ModID = 0x2, Subslot = 32769, SubId = 0x1

Module plugged; Api = 0, Slot = 0, ModID = 0x2, Subslot = 32770, SubId = 0x1

Module plugged; Api = 0, Slot = 1, ModID = 0x30, Subslot = 1, SubId = 0x1

Module plugged; Api = 0, Slot = 2, ModID = 0x31, Subslot = 1, SubId = 0x1

##PARAM END for all submodules, ArHndl=1, Session=1

##Event -submodule state request, Api=0 Slot=1 Subslot=1

##Event -submodule state request, Api=0 Slot=2 Subslot=1

##REMA PRM SHADOW OPEN

##REMA PRM SHADOW WRITE slot=0 sub=32768 rec=0x10000 len=8

##REC_DATA = 0xf0 0x 0 0x 0 0x 4 0x 1 0x 0 0x 0 0x20

##REMA PRM SHADOW CLOSE

##REMA SHADOW MEM STORE NumOfRecords=1, total memsize=56

##REMA PRM SHADOW COMMIT

***Bsp_nv_data_store:NvDataType=2***

##AR IN-Data event indication received, ArHndl = 1h, Session = 1h

***Bsp_nv_data_store:NvDataType=2:NL=38 OL=38Data for Flash***

new IO controller consumer status = 0x80 in slot 0, subslot 1

1. After user data exchange begins, the both SF LED and the BF 2 LED on the CPU should go out. The RX/TX

lamp is permanently on or flashes, depending on the update time configured in HW Config (1 ms to 128 ms).

2. Your PROFINET IO device now exchanges user data cyclically with the controller. In Simatic Manager, you

can create a variable table with the IO data of your device to monitor the user data exchange. When you click

the device in your PROFINET IO configuration (HW Config), the modules in the corresponding slots are

displayed in a table. The I-addresses and O-addresses in the S7 CPU slots are mapped to these modules.

3. You can read the current content of the user data on the PNIO device by entering j (print cyclic io data

) on

the Tornado terminal interface. Each time you press j the current status of the data is read once. The

displayed data content must match that of the STEP 7 variable table.

4. Continue to familiarize yourself with the user example. You can carry out various commands by making

various entries on the terminal interface.

Technical data subject to change Version 3.0.0