Technical data

ManualsBrandsSiemens ManualsComputer equipmentERTEC EB 200

Technical data subject to change Version 1.0.1

Contents

1 Introduction .................................................................................................................................. 8

1.1 Procedure when using ERTEC 200P to develop your own PROFINET IO Device .................................. 8

1.2 Structure of the EB 200P .............................................................................................................................. 9

1.3 Features of the EB 200P .............................................................................................................................. 9

1.4 Block Diagram of the EB 200P ..................................................................................................................... 10

2 Hardware Structure of the EB 200P ......................................................................................... 11

2.1 ERTEC 200P ................................................................................................................................................. 11

2.1.1 Function Overview .................................................................................................................................. 11

2.1.2 Operating Modes of the EB 200P .......................................................................................................... 12

2.1.3 Boot Modes of the EB 200P ................................................................................................................... 13

2.1.4 ERTEC 200P Processor and I/O ............................................................................................................ 13

2.1.5 PNIP 14

2.1.6 External Memory Controller (EMC) ........................................................................................................ 14

2.1.7 Debug and Trace Interface ..................................................................................................................... 14

2.1.8 General Purpose Interface (GPIO)......................................................................................................... 15

2.2 Memory on EB 200P ..................................................................................................................................... 18

2.2.1 SDRAM .................................................................................................................................................... 18

2.2.2 Burst Mode FLASH ................................................................................................................................. 18

2.2.3 I2C EEPROM .......................................................................................................................................... 18

2.3 Test and debug peripherals .......................................................................................................................... 19

2.3.1 Status LEDs ............................................................................................................................................. 19

2.3.2 Synchronization output and input ........................................................................................................... 20

2.3.3 SPI temperature sensor .......................................................................................................................... 20

2.3.4 User GPIOs with LEDs and switch......................................................................................................... 21

2.3.5 UART over USB ...................................................................................................................................... 21

2.4 Reset System of the EB 200P ...................................................................................................................... 22

2.4.1 Reset Button ............................................................................................................................................ 22

2.4.2 PCI Express Reset .................................................................................................................................. 22

2.4.3 Watchdog and Software Reset............................................................................................................... 22

2.5 Clock System of the EB 200P ...................................................................................................................... 23

2.5.1 Clock Source of PCI Express Interface ................................................................................................. 23

2.5.2 Clock Source of EB 200P via a Quartz Crystal ..................................................................................... 23

2.6 Ethernet Interfaces of the EB 200P ............................................................................................................. 24

2.6.1 Ethernet ports (X1) .................................................................................................................................. 24

2.6.2 TAP ports (X1) ......................................................................................................................................... 24

2.6.3 POF Transceiver ports (X3, X4) ............................................................................................................. 24

3 Memory Allocation of EB 200P ................................................................................................. 25

3.1 Memory Mapping .......................................................................................................................................... 25

4 Operating Modes of the EB 200P.............................................................................................. 26

4.1 Operating the EB 200P without programmed Flash ................................................................................... 26

4.2 Operating the EB 200P with programmed Flash......................................................................................... 26

4.3 Operating the EB 200P in XHIF Mode ......................................................................................................... 26

5 Debug/ Boundary scan Interface .............................................................................................. 27

6 Connectors of the EB 200P ....................................................................................................... 28

6.1 PCI Express x1 Interface .............................................................................................................................. 29

6.2 External DC Power Supply ........................................................................................................................... 29

6.3 Ethernet and TAP RJ-45 interface ............................................................................................................... 30

6.4 Sync connector.............................................................................................................................................. 31

6.5 USB-UART Interface..................................................................................................................................... 31

6.6 EMC interface................................................................................................................................................ 31

6.7 User GPIO [15 to 0] ...................................................................................................................................... 33

6.8 JTAG connector for FPGA............................................................................................................................ 34

6.9 GPIO [95 to 0] connectors ............................................................................................................................ 34

6.10 Trace connector for ETM of ARM926EJ-S .................................................................................................. 36

6.11 JTAG connector for ICE or debugger .......................................................................................................... 37