User Manual

ManualsBrandsSiemens ManualsBuilding automationConnect X300

A6V11473182

_en--_b

Building Technologies

2019-04-07

Connect X300

CXG3.X300

Connect X300 for the cloud integration of Siemens Building Technologies as well

as third-party systems

●

2 Ethernet ports for WAN and LAN

●

Remote firmware and configuration data update over the IP Interface

●

LED indication of activities and state

●

Operating voltage DC 24 V =

●

Plug-in screw terminal block for supply

●

Mounting on standard rails or on wall

Depending on firmware, the following functions are supported (examples):

●

Multi-site management

●

Remote operation & monitoring

●

Alarm treatment

●

Remote tool access

Summary of content (8 pages)

PAGE 1
Connect X300 CXG3.
PAGE 2
Features Connect X300 is a physical device that is the connecting point between the cloud and controlled/monitored devices. This can include controllers, sensors, and actuators in the building etc. Application The device integrates BACnet/IP or Modbus/TCP devices and systems as well as FS20 fire panels. It securely transmits data to the cloud over cabled networks or over mobile networks (4G: With a router). A USB dongle is planned for 4G support.
PAGE 3
LED displays LED PC ON/ WD L1 L2 L3 Activity Function Off Device off Green BIOS ready to boot Green/red flashing BIOS in Power On Self Test (POST) Yellow Idling Red flashing (1 Hz) Watchdog state error  Switch off device, wait 1 minute, then switch on again Green, flashing Start SW applications Green All SW application operational Yellow flashing Communication to the cloud Yellow Network connection stable; no communication to the cloud Off No communication to the cloud -- Not use
PAGE 4
Notes Safety CAUTION National safety regulations Failure to comply with national safety regulations may result in personal injury and property damage. ● Observe national provisions and comply with the appropriate safety regulations. High temperature on device surface during operation (to 70 °C / 158 °F) Mounting The device is suitable for mounting on standard rails. Mounting position and temperature range Provide sufficient ventilation in the Max. 50 °C (122 °F) Min.
PAGE 5
Maintenance: Replace battery The BIOS backup battery must be replaced every 5 years. See accessories for order number. Procedure: 0 Assure protection against electrostatic discharge (ESD) 1. Disconnect device from power 2. Unscrew 6 screws on the base plant (T20) and carefully remove the base plate 3. Disconnect the ribbon cable on the SSD (not on the motherboard) 4. Remove the battery from the housing wall 5. Remove the remaining Velcro strips from the housing wall 6. Unplug the old battery 7.
PAGE 6
Technical data Power supply Operating voltage (M, L+) DC 24 V = only (direct current) DC 24 V = ± 20 % Safety extra-low voltage SELV per IEC/EN / DIN EN / UL 60950-1 or NEC Class 2 or LPS per IEC/EN / DIN EN / UL 60950-1 Diameter min. 2.5 mm2 /14AWG The protective earth connection must be connected on the installation side with the building grounding system (PE). Power consumption Max. 1.
PAGE 7
Serial interface (Unused) 2x COM D-sub plug, 9-pin Protocol EIA-485 Bit rate Max 115 Kbps Screen interface (Unused) 1x DisplayPort 640 x 480 ... 2560 x 1600 Pixel Conformity Ambient conditions and protection classification Design Protection class I per IEC 61140 Degree of protection of housing to EN 60529 IP40 Dust protection Against foreign particles ≥1 mm Climatic ambient conditions ● Transport (packaged for transportation) to EN 60721-3-2 ● Temperature -20...60 °C (-4...
PAGE 8
Connections and indicators 1 3 4 5 6 7 8 1 Protective earth 2 Pluggable terminal block for operating voltage DC 24 V = 3 On/off switch. OFF, when pressing symbol "C-" 9 The protective earth connection must be connected on the installation side with the building grounding system (PE). Diameter min. 2.5 mm2 /14 AWG 4 USB 2.0, 3.