User Manual

ManualsBrandsSiemens ManualsBuilding automationConnect X300

A6V11473182_en--_d

Smart Infrastructure

2020-11-20

Connect X300

CXG3.X300

Connect X300 for the cloud integration of Siemens Smart Infrastructure as well as

third-party systems

 2 Ethernet ports for WAN and LAN

 Remote firmware and configuration data update over the IP Interface

 LED indication of activities and state

 Operating voltage DC 24 V =

 Plug-in screw terminal block for supply

 Mounting on standard rails or on wall

Depending on firmware, the following functions are supported (examples):

 Multi-site management

 Remote operation & monitoring

 Alarm treatment

 Remote tool access

The specific set of supported functions may vary according to the region

(for example UL markets) and according to the connected system.

Summary of content (8 pages)

PAGE 1
Connect X300 CXG3.
PAGE 2
Features Connect X300 is a physical device that is the connecting point between the cloud and controlled/monitored devices. This can include controllers, sensors, and actuators in the building etc. Application The device integrates BACnet/IP or Modbus/TCP devices and systems as well as FS20 fire panels. It securely transmits data to the cloud over cabled networks or over mobile networks (e.g. 4G: With a router). 4G USB Dongle support is available in addition (see “Accessories”).
PAGE 3
LED displays LED Activity Function PC ON/ WD Off Device off Orange flashing BIOS in Power On Self Test (POST) Solid Green Device ready (otherwise re-start the device) Green, flashing SW applications starting Solid Green All SW application operational Off Approx. 1 minute off during start-up Solid Orange Internet OK Orange flashing X300 is registered properly and Cloud connection is OK.
PAGE 4
compatibility of regional 4G frequency bands). Consult “4G Dongle Commissioning Guide” for further instructions and information. Product documentation All relevant documents can be downloaded at the following Internet address: http://siemens.com/bt/download (Enter type CXG3.X300). Notes Safety CAUTION National safety regulations Failure to comply with national safety regulations may result in personal injury and property damage.
PAGE 5
Maintenance: Replace battery The BIOS backup battery is installed ex works and must be replaced every 5 years. See accessories for type number. Procedure: 1. Assure protection against electrostatic discharge (ESD). 2. Disconnect device from power. 3. Unscrew 6 screws on the base plant (T20) and carefully remove the base plate. 4. Disconnect the ribbon cable on the SSD (not on the motherboard). 5. Remove the battery from the housing wall. 6. Remove the remaining Velcro strips from the housing wall. 7.
PAGE 6
Technical data Power supply Operating voltage (M, L+) DC 24 V = ± 20 % Safety extra-low voltage SELV per IEC/EN / DIN EN / UL 60950-1 or DC 24 V = Direct current only! NEC Class 2 or LPS per IEC/EN / DIN EN / UL 60950-1 Cross section min. 2.5 mm2 /14AWG The protective earth connection must be connected on the installation side with the building grounding system (PE). Power consumption Max. 1.
PAGE 7
Serial interface (Unused) 2x COM D-sub plug, 9-pin Protocol EIA-485 Bit rate Max 115 Kbps Screen interface (Unused) 1x DisplayPort 640 x 480 ... 2560 x 1600 Pixel Conformity Ambient conditions and protection classification Design Protection class I per IEC 61140 Degree of protection of housing to EN 60529 IP40 Dust protection Against foreign particles ≥1 mm Climatic ambient conditions  Transport (packaged for transportation) to EN 60721-3-2  Temperature -20...60 °C (-4...
PAGE 8
Housing Dimensions See "Dimensions” Weight without / with packaging 1590 g / 1940 g Connections and indicators 1 3 4 5 6 7 8 9 1 Protective earth The protective earth connection must be connected on the installation side with the building grounding system (PE). Diameter min. 2.5 mm2 /14 AWG 2 Pluggable terminal block for operating voltage DC 24 V = 3 On/off switch. OFF, when pressing symbol "C-" 4 USB 2.0, 3.