Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Table of contents Preparing to use your phone................................................................................... 4 The pack contains ................................................................................................... 4 Installing the phone ................................................................................................ 4 Descriptions of displays of the handset and the base .........
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Browsing incoming call records.................................................................... 16 Storing the incoming call numbers to the directory (base and handset)........ 17 Deleting individual incoming call numbers .................................................. 17 Deleting all incoming numbers ..................................................................... 17 Browsing and dial the incoming numbers ............
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Preparing to use the phone The pack contains: z z z z z z z z z Base Handset Microphone. Microphone cord (coiled) Rechargeable batteries Charger Phone cord Two power supply units with power cord One set of operating instruction Installing the phone 1. To open the battery compartment, press the battery cover of the handset and slide it down. 2.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Note: The dial mode of this phone has been set to tone dialing. If you want to change it to pulse dialing, please refer to the descriptions in the “Tone/Pulse Switch” section. If you are not sure which mode to apply, please consult your phone service company. 10.Place your base away from the “interference sources” (e.g.: TV, PC, microwave oven, refrigerator, etc.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Settings “Tone/pulse” switch On the rare of the base is a “Tone/Pulse” switch for tone or pulse mode selection. “Flash timing” switch On the rare of the base is a “Flash time” switch with three flash time selections, 90ms, 270ms and 600ms. (For use in China, set it to be 600ms) Note: the flash time is effective only by setting it before connected to power and phone cord.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Adding IDD code to the incoming calls (handset and base) Press the Mem/Prog key for 3 seconds Press Channel/Select key till “Lo CodE” appears Enter one digit of IDD code, which can be deleted by pressing the Flash/Clear key.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Selecting VIP Ringer Tones (handset and base) Press the Mem/Prog key for 3 seconds Press the Channel/Select key until “VIP Ring” appears Press Ʒ or ͩ to select the ringer melody. (8 melodies) Press the Mem/Prog key for confirmation Press Exit to exit Note: you must apply for “Show incoming call number” service (or Caller ID Service) to validate this function.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 The base Adjusting the ringer volume Be sure the base is in standby. Press the Mem/Prog key. Then press the # key, the handset will sound a confirmation tone. The ring volume is set to “low volume”. (If the * key is pressed, the volume will be set to “high volume”.) Handset and base Deactivate ringer Be sure both the handset and the base are in standby. Press the Mem/Prog key.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Basic operation Answering/Ending a call Base Press the Hands-free/Dial back key to answer a call, and press the same key to end a call. Or pick up the handset of the base to answer, then put it down to end. Handset Press the Talk key to answer a call. Press the same key or place the handset back to its charger to hang up. Making A Call Base Press the Hands-free/Dial back key and then dial a number.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 automatically dialed out. Or Press the Talk key on the handset or the Hands-free/Dial back key on the base. Press the Redial key to automatically dial out the last dialed number. Deleting a single outgoing number Be sure the handset or the base is in standby. Press the Outgoing Call (Redial) ͩ key. Press Ʒ or ͩ key to browse and select the outgoing records. Then press the Flash/Clear key on the handset or the base.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 the user wants to operate in their internal system, then he/she must change the pulse dialing to tone dialing temporarily. For example, you are required to enter your bank account number: 1. Dial the bank’s number. 2. Press * key when putting through. 3. Act according to the voice instructions over the phone. 4. When finish, you can hang up the phone, and then the phone returns to pulse dialing.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 relevant handset and the handset will ring, which can last 60 seconds. If the user doesn’t dial the handset number, all handsets will ring. Press the Talk key on the handset to start talking to the base. (If the handset user will not answer the call, simply press the Talk key or put the handset back on the charger to terminate the inter-talking.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Handset: New incoming call indicator The number of new incoming calls The incoming phone number Base: Date Time New incoming call indicator The number of new incoming calls The incoming phone number Note: You must apply for the Caller ID Service from your telecom companies to enable this function.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Press again the same key to delete the selected record. Storing the incoming call numbers to the directory (base and handset) Be sure the base and the handset is in standby. Press CID Ʒ key. Press Ʒ or Ʒ key to browse and select incoming call records. Press the Mem/Prog key. Then enter two digits (01-16) of the location where the number should be stored. Note: the “0” in the “01” cannot be omitted.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 phone numbers in the directory. The incoming phone numbers can also be stored in the directory. Storing phone numbers Be sure the handset or the base is in Standby. Enter the phone number (maximal 20 digits). Press the Mem/Prog key and then enter the location the number will be stored to (01-16). Browsing lists in the Directory Be sure the handset or the base is in Standby.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Press Ʒ or ͩ key to browse the records. Press the Mem/Prog key and “VIP” will appear on the display. (Press Mem/Prog again to cancel the VIP setting.) Note: When finished, press the Exit key to exit. Dialing from stored caller-ID Press Select key until “Store” appears on the display. Press Ʒ or ͩ key to browse and select the stored records. If too long, press the 0/ Next key to display other lists.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Speed dial This function is designed for users who frequently make long distance calls. Following the instructions, you can speed dial a number: For example: Parts of a long-distance number Area Code Phone number Extension Location in the Directory 07 08 09 Press either the Talk or the Hands-free/Dial Back key. Press the Mem/Prog key, and then press 07.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 - Press twice the Redial/Pause key. - Press 1 (for Mandarin) - Press twice the Redial/Pause key. - Enter 1373110888889888 (the card number and pin). - Press #. - Press the Mem/Prog key to confirm. Note: Above program is just for reference only, you can set different program by different cards.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Set to lock the numbers beginning with “0” (please set on the handset and base) User can restrict the numbers beginning with “0”, Follow the following steps: Successively press #, #. Enter PIN 0588. Enter the restricted number 0. Press the Mem/Prog key to confirm. The handset or the base will make a confirmation tone. Unlocking Successively press #, #. Enter PIN 0588. Press the Save/Set key to confirm.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 at least 30 minutes. Replacing batteries Be sure the handset is in standby. 1. To open the battery compartment, press the battery cover of the handset and slide it down. 2. Take out the batteries. 3. Insert new batteries into the battery compartment. 4. Push up the battery cover. 5. Place the handset with batteries inserted back in its the charger. 6.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Q&A Caller numbers Question No display Show error about the caller’s information Answer Replace the batteries and be sure they are inserted correctly. Have you applied for the Incoming Call Display service from your phone service company? If the base receives any information that is different from the valid incoming call information, it will show error.
Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 umschl_v.fm 16.10.03 Hotline Hotline email ˖ccq_cp.com@siemens.com Hotline service tel ˖4006 706 007 Website: www.siemens.com.
Appendix (Interface Illustration) HANDSET Channel/Select(directory/incoming records/outgoing call records) To Enter Directory/Set program adjust volume / Incoming call / Outgoing call To Exit the program / Intercom Talk/End IP numbers storage or dialing change the pulse dialing to tone dialing temporarily To Redial / dialing pause End/delete/handset registration Next page
Base (Top and side) pow er Incoming call / Outgoing call delete/handset registration using Select To Enter Directory/Set program To Exit the program / Intercom IP numbers storage or dialing change the pulse dialing to tone dialing temporarily hold vo lum e/tim e flas h To Redial / dialing pause Next page Loudspeaker hands free Corded Handset
Base (Bottom and Rear) Mechanical “0” Lock T/P Switch Flash timing Switch Line Jack
